Siemens FDOOT241-A3 User manual

Smart Infrastructure
Sinteso™ S
-
LINE
Multisensor fire detectors
FDOOT241-A3, FDOOT241-A4, FDOOT241-A5, FDOOT241-A9, FDOOT241-8
Multi
-
sensor fire detector for gradual modernization with ASAtechnology™
●For the modernization of collective/GMT/SynoLINE300, AlgoRex AnalogPLUS,
and Interactive, SIGMALOOP, or MS8 on Sinteso FDnet
●Signal processing with ASAtechnology (Advanced Signal Analysis)
●Event-controlled detection behavior
●Early and reliable detection when fires occur
●Highly developed immunity to deceptive phenomena
●Maximum system availability thanks to sensory with redundancy
●Suitable for wind speeds of 1…20 m/s
●Ecological materials concept

2
Smart Infrastructure
Properties
Ecological benefits
●Environmentally friendly processing
●Reusable materials
●Electronic parts and synthetic materials can be easily separated
●Environmentally friendly detector-testing without gas
Features
●Resistant to environmental and interfering influences such as dust, fibers, insects,
moisture, extreme temperatures, electromagnetic interference, corrosive vapors,
vibration, artificial aerosols, and atypical fire phenomena
●Shock resistant, theft protection as an accessory
●Signal processing with ASAtechnology (Advanced Signal Analysis)
●Time and process-dependent detection behavior
●Proven immunity to faults in power electronics
●Protected electronics, high-quality components
●Sophisticated sensors and electronic monitoring
●Redundant, high-quality sensor system
●Internal alarm indicator (IAI), 360° visibility, alignment not necessary
●Integrated line separator

3
Smart Infrastructure
Use
Multi-sensor fire detector FDOOT241-A3, FDOOT241-A4, FDOOT241-A5, FDOOT241-A9, FDOOT241-8
Multi-sensor fire detector consisting of:
●Point detector with additional heat sensors
●Detector dust cap to protect the point detector during the construction phase
Function
●Functions according to the scattered light principle with two sensors: optical
forward and backward scattering
●Opto-electronic measuring chamber, obstructs disruptive extraneous light
but can be relied upon to detect both light and dark smoke particles
●Two additional heat sensors increase the fire detector's immunity to
deceptive phenomena
●Can be set as a multi-sensor smoke detector, smoke detector, or heat
detector by the software
●Selectable detection behavior thanks to application-specific ASA parameter
sets
●Multi-protocol:
– FDOOT241-A3 (AlgoRex AnalogPLUS, FDnet)
– FDOOT241-A4 (SIGMALOOP, FDnet)
– FDOOT241-A5 (AlgoRex Interactive, FDnet)
– FDOOT241-A9: Collective / GMT (Cerberus / Siemens) / SynoLINE300,
FDnet
– FDOOT241-8 (MS8/PMT, FDnet)
Use
●For early detection of flaming fires of solid and liquid substances as well as
of smoldering fires
●For early and reliable fire detection in an environment with deceptive
phenomena
●Can be used addressed, for the gradual modernization of:
– AlgoRex AnalogPLUS on Sinteso FDnet ¹ with FDOOT241-A3
– SIGMALOOP on Sinteso FDnet ¹ with FDOOT241-A4
– AlgoRex Interactive on Sinteso FDnet ¹ with FDOOT241-A5
– Collective/GMT/SynoLINE300 on Sinteso FDnet ¹ with FDOOT241-A9
– MS8/PMT on Sinteso FDnet with FDOOT241-8
¹ FS20 compatibility in FDnet is assured subject to in-country FS20 software support.

4
Smart Infrastructure
Type Overview
Type Order number Designation Weight [kg]
Point detector
FDOOT241-A3 S54310-F10-A1 Multi-sensor fire detector Sinteso (A+) 0.106
FDOOT241-A4 S54310-F9-A1 Multi-sensor fire detector Sinteso (SIGMA) 0.106
FDOOT241-A5 S54310-F14-A1 Multi-sensor fire detector Sinteso
(Interactive)
0.106
FDOOT241-A9 S54310-F11-A1 Multi-sensor fire detector Sinteso ASA 0.106
FDOOT241-8 A5Q00004663 Multi-sensor smoke detector Sinteso ASA 0.106
Migration kits
FDOOT241-8M A5Q00016038 Migration kit (FDOOT241-8 + FDB281) 0.235
FDOOT241-8B A5Q00015956 Migration kit (FDOOT241-8 + FDB221) 0.162
Base adapter
FDB241 S54319-F13-A1 Base adapter Sinteso (SIGMA/A+) 0.086
FDB251 S54319-F28-A1 Base adapter Sinteso (Interactive) 0.090
FDB281 A5Q00004929 Base adapter MS8/PMT 0.125
FDB299 S54319-F14-A1 Base adapter Sinteso (AlgoRex coll.) 0.086
Other accessories
FDUD290 S54370-S13-A1 Removal tool for adapter 0.098
You will find information about the color options for the fire detectors in the data sheet
009409.

5
Smart Infrastructure
Accessories
Base adapter FDB241
Function:
●For adapting AnalogPLUS and SIGMALOOP for Sinteso detector systems
●Can be set with jumper on replaced detector
Base adapter FDB251
Function:
●For adapting Interactive for Sinteso detector systems
●Can be set with jumper on replaced detector
Base adapter FDB281
Function:
●For adapting MS8/PMT for Sinteso detector systems
Base adapter FDB299
Function:
●For adapting AlgoRex (collective) and SIGMACON for Sinteso detector
systems
Removal tool for adapter FDUD290
Function:
●For removing base adapters FDB2xx with detector exchanger, detector
exchanger and tester, or detector tester

6
Smart Infrastructure
Applicable documents
Document ID Title
007004 Technical manual Automatic fire detectors FDOOT221, FDOOT241-A3, FDOOT241-
A4, FDOOT241-A5, FDOOT241-8, FDOOT241-9, FDOOT241-A9, FDO241, FDO221,
FDT241, FDT221
008116 Installation Base adapter FDB281
008164 Equipment overview Sinteso™ Detector system FD20
008331 List of compatibility (for 'Sinteso™' product line)
009409 Data sheet Colored detectors, bases and base attachment FDO.., FDOOT…, FDT…,
FDB…, FDCW241
A6V10301448 Installation Base adapter FDB299
A6V10301452 Installation Base adapter FDB241
A6V10323158 Technical manual Modernizing fire detection installations with multiple protocol
detectors
A6V10411361 Installation Base adapter FDB251
Notes
Efficiency on-site
●No wiring, detector replacement only
●Detectors can be replaced without a ladder at heights up to 8 m with the detector
exchanger FDUD291, detector exchanger and tester FDUD292, or intelligent detector
tester FDUD293 in combination with telescope or extension rod.

7
Smart Infrastructure
Installation
3
2
4
1
2
5
6
①Base adapter ②Point detector ③Detector base ④Detector exchanger/detector
exchanger and tester
⑤IAI
FDB241 FDOOT241-A3 AnalogPLUS (DB1131) FDUD291
FDUD292
FDUD293
Internal
alarm
indicator
FDOOT241-A4 SIGMALOOP (SPF3600)
FDB251 FDOOT241-A5 Interactive (DB1151A)
FDB299 FDOOT241-A9 AlgoRex collective
(DB1101A)/
SIGMACON (SPF600)
FDB281 FDOOT241-8 ⑥MS8 (Z84)
1. Screw the point detector into the base adapter.
2. Screw the point detector with the attached base adapter into the detector base by hand
or with a detector exchanger or detector exchanger and tester.
aThe point detector is mounted.
Disposal
The device is considered an electronic device for disposal in accordance
with the European Guidelines and may not be disposed of as domestic
garbage.
●Dispose of the device through channels provided for this purpose.
●Comply with all local and currently applicable laws and regulations.
●Dispose of empty batteries in designated collection points.

8
Smart Infrastructure
Technical data
FDOOT241-A3 FDOOT241-A4 FDOOT241-A5 FDOOT241-A9 FDOOT241-8
FDOOT241-A3,
FDOOT241-A4,
FDOOT241-A5,
FDOOT241-A9
FDOOT241-8
In the
AnalogPLUS
detector system
In the
SIGMALOOP
detector system
In the Interactive
detector system
In the collective
detector system
In the MS8
detector system
In FDnet
Operating voltage
(modulated)
DC 16…28 V DC 10…28 V DC 21…33 V DC 14…28 V DC 14…28 V DC 12…33 V
Operating current
(quiescent)
190 μA 200 μA 200 μA 65…125 μA 200 μA 190…230 μA
External alarm
indicators (AI) which
can be connected
2 2 2 2 2 2
Communication
protocol
AnalogPLUS SIGMALOOP Interactive Collective MS8/PMT FDnet
System compatibility AlgoRex SIGMASYS AlgoRex AlgoRex,
SIGMASYS,
CZ10
SIGMASYS,
BMS,
SM80/88/D100,
SRS
FS20 ¹
Operating
temperature
-25…+70°C -25…+70°C -25…+70°C -35…+70°C -25…+70°C -
Storage temperature -30…+75°C -30…+75°C -30…+75°C -35…+75°C -30…+75°C -
Humidity ≤95 % rel.
Color ~RAL 9010 pure white
Protection category
(IEC 60529)
with detector base
FDB221, FDB222
IP43
Base attachment
FDB291
IP43
Base adapter FDB281 IP44
Base adapter FDB241
and
detector base
DB1131A, or
SPF3600
IP44
Base adapter FDB251
and
detector base
DB1151A
IP44
Base adapter FDB299
and
collective detector
base DB1101A or
SPF600
IP44
Standards EN 54-5, EN 54-7, EN 54-17, EN 54-27 2, EN 54-29 3
Approvals
VdS
LPCB (except
EN 54-27)
DNV GL (marine)
G211125
126bv/02
–
G212007
–
–
G215057
126bv/01
–
G212036
126bv/03
MEDB00003UK
G204133
–
–
–
–
–
Permissible wind
speed
1…20 m/s
¹ FS20 compatibility in FDnet is assured subject to in-country FS20 software support.
2EN 54-27 for FDOOT241-A3, FDOOT241-A4, FDOOT241-A9 only
3EN 54-29 for FDOOT241-A3, FDOOT241-A4, FDOOT241-A5, FDOOT241-A9 only

9
Smart Infrastructure
Dimensional drawing
b
a
Combination
Dimension 'a' Dimension 'b' with
detector base
Dimension 'b'
without detector
base
Detector base AnalogPLUS (DB1131A)
Base adapter FDB241
Multi-sensor fire detector FDOOT241-A3
117 77.9 73.3
Detector base AnalogPLUS (SPF3600)
Base adapter FDB241
Multi-sensor fire detector FDOOT241-A4
Detector base Collective (DB1101A or
SPF600)
Base adapter FDB299
Multi-sensor fire detector FDOOT241-A9
Detector base Interactive (DB1151A)
Base adapter FDB251
Multi-sensor fire detector FDOOT241-A5
Detector base MS8
Base adapter FDB281
Multi-sensor smoke detector FDOOT241-8
91.4 73.5