Siemens SBGA-34 User manual

Siemens Industry, Inc.
Building TechnologiesDivision
Florham Park, NJ
P/N A6V10383428_a_en--
INSTALLATION INSTRUCTIONS
Model SBGA-34
Audible Base
INTRODUCTION
The ModelSBGA-34 Audible Base from Siemens Industry, Inc., consists of a standard Series 11 base
combined with an audible device compatible with all H-series, 8700 series, Desigo and Cerberus series
addressable detectors. All field wiring terminates at two four-position terminal blocks located on the back
of the unit. The SBGA-34 is used with the polarity insensitive HFP-11, HFPT-11, HFPO-11, SFP-11*,
SFPT-11* and SFPO-11*, 8710, 8712, 8713, FDO421, FDT421, FDOT421, FDOOT441, FDOOTC441,
OP921, OH921, HI921, OOH941, OOHC941 detectors. The SBGA-34 operates as described below
(Refer to Figures 1, 2, 3, 4, 5, 6 and 7 for proper wiring connections).
*SFP-11, SFPT-11 and SFPO-11 detectors are approved for use in CANADA only.
JA-BI20 (3 WIRE)
JA-BI24 (7 WIRE)
JS-24 (1 WIRE) FROM PIN 3 OF LAST MODULE
JA-5
(10 WIRE)
NOTE:
WHEN THE OPTIONAL MM-35 IS NOT USED,
A SUPERVISORY CONNECTION MODEL
JP-BE MUST BE INSTALLED AT P2 IN THE
LAST BC-35 OR BE-35 MODEL.
FOR P1 CONNECTION USE
JA-24 OR EQUIVALENT, AND
REWORK AS NECESSARY
BI-35
AA-30U
SBGA-34
DB-11
STYLE Y
(CLASS B)
STYLE Z
(CLASS A)
BC-35
AE-30U
24 VDC
BATTERY
PS-35
POWER INPUT
120 VAC, 50/60 Hz
CONNECTED TO GROUND
REFERENCE OF THE PANELS
IT’S CONNECTED TO (REFER
TO TABLE X FOR GROUND
CONNECTION)
LINE 2
LINE 1
LINE 1
LINE 2
LINE 2
LINE 1
FOR CONNECTION
TO SLC LOOP
FROM DLC LOOP OF SYSTEM OR FS-DLC LOOP OF FS-250 SYSTEMFIREFINDER-XLS
TO NEXT
SBGA-34, DB3S,
DB-X3RS, OR DB-11
+
+
+
+
+
+
+ + + + +
+
+
-
-
- -
-
-
-
-
-
-
-
4 4
4
4
8
8
12-PIN
PLUG
5 5
55
9
6 6
66
10
3 3
33
7
7
2 2
2 2
1 1
1
1
3
5
7
9
2
4
6
8
10
6
5
1a
1b
1
8
8
8
8
7
7
7
7
6
6
6
6
5
5
5
5
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
P1
P1 P2
P2
P1
P2
P1
7
8
3.6K,
1/4W,
MODEL
EL-31
3.6K,
1/4W,
MODEL
EL-31
NOTE 1
NOTE 3
NOTE 1
NOTE 3
NOTE 4
NOTE 4
3.6K,
1/4W,
MODEL
EL-31
1. Polarity shown in active state at terminals 1 and 2 of SBGA-34. Proper
polarity must be maintained or audible base will not operate properly.
Each audible base must be tested to verify operation.
2. Use a Model MPI-2 mounting plate to mount a HTRI-R in a System 3
enclosure. HTRI-R relay should be programmed to activate on
appropriate alarm condition. For more detailed wiring information, refer
to the HTRI-R Installation Instructions, P/N 315-033300.
3. Tone selection (refer to page 7 for more information).
4. HTRI-R and SBGA-34 are polarity insensitive. Line 1 and Line 2 can
be either line of the loop.
NOTE 2
HTRI-R
8
7
6
5
4
3
2
1
SBGA-34
SBGA-34
SBGA-34
Figure 1
Installation/Wiring Diagram for SBGA-34 Powered by Auxiliary Power Supply with Battery Backup

1. Polarity shown in active state at terminals 1 and 2 of SBGA-34 and 1-4 of ZIC-4A.
Proper polarity must be maintained or audible base will not operate properly. Each
audible base must be tested to verify operation.
2. Tone selection (refer to page 7 for more information).
3. SBGA-34 terminals 5-8 are polarity insensitive. Line 1 and Line 2 can be either line
of the loop.
4. SBGA-34 shown Style Z (Class A). It may also be wired as Style Y (Class B).
5. ZIC-4A Notification Applicance Circuits provide 4 outputs that can be configured for
Class A. or Class B. Refer to the ZIC-4A Installation Instructions, P/N 315-033050.
6. EOL resistor, 24k ohms, ½ watt, 5%, P/N 140-820405.
7. For synchronized operation using the ZIC output, tone selection in the SBGA-34
must be set to Steady.
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
+ +
--
ZONE 3
ZONE 2
ZONE 4
ZIC-4A
SBGA-34 SBGA-34
-
+
-
+
5
6
1b
1a
8 87 76 65 5
1 12 23 34 4
TO NEXT
ADDRESSABLE
DEVICE
LINE 1
LINE 2
LINE 1
LINE 2
24K
1/2W
5%
FROM DLC LOOP OF
FIREFINDER-XLS
SYSTEM
NOTE 2
NOTE 2
NOTE 3
NOTE 3
Figure 2
Installation/Wiring Diagram for SBGA-34 Audible Powered by ZIC-4A (FireFinder-XLS System)
1. Polarity shown in active state at terminals 1 and 2 of SBGA-34 and 1-4 of ZIC-8B.
Proper polarity must be maintained or audible base will not operate properly. Each
audible base must be tested to verify operation.
2. Tone selection (refer to page 7 for more information).
3. SBGA-34 terminals 5-8 are polarity insensitive. Line 1 and Line 2 can be either line
of the loop.
4. SBGA-34 shown as Style Y (Class B).
5. ZIC-8B Notification Applicance Circuits provide 8 outputs that can be configured for
Class B. Refer to the ZIC-8B Installation Instructions, P/N 315-048670.
6. EOL resistor, 24k ohms, ½ watt, 5%, P/N 140-820405.
7. For synchronized operation using the ZIC output, tone selection in the SBGA-34
must be set to Steady.
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
ZONE 3
ZONE 2
ZONE 4
ZIC-8B
SBGA-34 SBGA-34
-
+
-
+
5
6
1b
1a
8 87 76 65 5
1 12 23 34 4
TO NEXT
ADDRESSABLE
DEVICE
LINE 1
LINE 2
LINE 1
LINE 2
FROM DLC LOOP OF
FIREFINDER-XLS
SYSTEM
NOTE 2NOTE 2
NOTE 3
NOTE 3
ZONE 5
ZONE 6
ZONE 7
ZONE 8
ZONE 1
24K
1/2W
5%
-
+
Figure 3
Installation/Wiring Diagram for SBGA-34 Audible Powered by ZIC-8B (FireFinder-XLS System)

1. Polarity shown in active state at terminals 1 and 2 of SBGA-34 and 1+, 1-, 2+ and 2-
of FS-250/FS-250C NAC cirucits. Proper polarity must be maintained or audible
base will not operate properly. Each audible base must be tested to verify operation.
2. Tone selection (refer to page 7 for more information).
3. SBGA-34 terminals 5-8 are polarity insensitive. Line 1 and Line 2 can be either line
of the loop.
4. SBGA-34 shown Style Z (Class A). It may also be wired as Style Y (Class B).
5. FS-250/FS-250C Notification Applicance Circuits (TB12 and TB13) provide 4
outputs that can be configured for Class B or two outputs that can be configured for
Class A. Refer to the FS-250 Operation, Installation and Maintenance Manual, P/N
315-049353, or the FS-250C Operation, Installation and Maintenance Manual, P/N
315-049589C, as applicable, to set jumpers JP1-4 for Class A or Class B operation.
6. EOL resistor, 24k ohms, ½ watt, 5%, P/N 140-820405.
SBGA-34 SBGA-34
-
+
-
+
5
6
1b
1a
8 87 76 65 5
1 12 23 34 4
TO NEXT
ADDRESSABLE
DEVICE
LINE 1
LINE 2
LINE 1
LINE 2
24K
1/2W
5%
FROM FS-DLC OR FDLC
LOOP OF FS-250
OR FS-250C SYSTEM
NOTE 2
NOTE 2
NOTE 3
NOTE 3
TB12
TB13
4-
3-
4+
3+
2-
1-
2+
1+
TB8 TB7
NO NC C NC NO C
Figure 4
Installation/Wiring Diagram for SBGA-34 Audible Powered by NAC Circuits (FS-250/FS-250C Systems
and MPC6000/MPC7000)
SBGA-34 SBGA-34
-
+
-
+
5
6
1b
1a
8 87 76 65 5
1 12 23 34 4
TO NEXT
ADDRESSABLE
DEVICE
TO PAD-3
NAC CIRCUIT
TO PAD-3
NAC CIRCUIT
LINE 1
LINE 2
LINE 1
LINE 2
EOL 2.2K, 1/2W
P/N 140-820380
NOTE 2NOTE 2
NOTE 3
NOTE 5
NOTE 3
1. NAC circuits polarity shown in active state. Proper polarity must
be maintained or audible base will not operate properly. Each
audible base must be tested to verify operation.
2. Tone selection (refer to page 7 for more information).
3. SBGA-34 is polarity insensitive. Line 1 and Line 2 can be either
line of the loop.
4. SBGA-34 shown Style Z (Class A). It may also be wired as
Style Y (Class B).
5. Max. Current 3.0 AMPS. Refer to PAD-3 Installation Instructions,
P/N 315-099082.
Figure 5
Installation/Wiring Diagram for SBGA-34 Audible Powered by PAD-3

1. Polarity shown in active state at terminals 1 and 2 of SBGA-34 and 1+, 1-, 2+ and 2-
of FC-901 NAC circuits. Proper polarity must be maintained or audible base will not
operate properly. Each audible base must be tested to verify operation.
2. Tone selection (refer to page 7 for more information).
3. SBGA-34 terminals 5-8 are polarity insensitive. Line 1 and Line 2 can be either line
of the loop.
4. SBGA-34 shown Style Z (Class A). It may also be wired as Style Y (Class B).
5. FC901 NotificationAppliance outputs that can be configured for Class B or Class A.
Refer to the FC-901 Operation, Installation and Maintenance Manual, P/N 315-
XXXXXX, as applicable, to set jumpers JP1-4 for ClassA or Class B operation.
SBGA-34 SBGA-34
-
+
-
+
8 87 76 65 5
1 12 23 34 4
TO NEXT
ADDRESSABLE
DEVICE
LINE 1
LINE 2
LINE 1
LINE 2
FROM P2
OF FC-901 PANEL
NOTE 2
NOTE 2
NOTE 3
NOTE 3
N_BN N_BP
N_AN N_AP
Figure 6
Installation/Wiring Diagram for SBGA-34 Audible connected to FC901 Panel
1. Polarity shown in active state at terminals 1 and 2 of SBGA-34 and 1+, 1-, 2+ and 2-
of FC2025/2050 FC922/924 NAC circuits. Proper polarity must be maintained or
audible base will not operate properly. Each audible base must be tested to verify
operation.
2. Tone selection (refer to page 7 for more information).
3. SBGA-34 terminals 5-8 are polarity insensitive. Line 1 and Line 2 can be either line
of the loop.
4. SBGA-34 shown Style Z (Class A). It may also be wired as Style Y (Class B).
5. FC2025/2050 FC922/924 Notification Appliance outputs that can be configured for
Class B or Class A. Refer to the FC2025/2050 Operation, Installation and
Maintenance Manual, P/N A6V10337045, or the FC922/924 Installation Instructions,
P/N A6V10356958, as applicable, to set jumpers JP1-4 for Class Aor Class B
operation.
SBGA-34 SBGA-34
-
+
-
+
8 87 76 65 5
1 12 23 34 4
TO NEXT
ADDRESSABLE
DEVICE
LINE 1
LINE 2
LINE 1
LINE 2
FROM P2
OF FC2025/2050
FC922/924
NOTE 2NOTE 2
NOTE 3
NOTE 3
NAC1-2 NAC1-2 NAC1-1 NAC1-11
2 3 4
+
+ - -
Figure 7
Installation/Wiring Diagram for SBGA-34 Audible to FS20 Panel

The SBGA-34 can generate steady, temporal-3 or temporal-4 tone when powered from 24VDC UL listed
aux power source or can be configured to follow the NAC tone pattern that is dependent of the panel
being used. Refer to the Tone Selection section to configure the units for stand-alone operation.
APPLICATION NOTE
The SBGA-34 is a UL268 and UL464 listed smoke detector supplementary devices which combines
detector base and audible device functions. When used in conjunction with the listed compatible Siemens
equipment, the SBGA-34 may be used in lieu of single/multiple station smoke alarms to achieve
enhanced, system level functionality.
When used to follow the NAC tone pattern, the SBGA-34 must be set to steady tone and the panel it is
connected to must be configured accordingly for the desired application. This allows the SBGA-34 to
transition from one tone to another (example from temporal 4 to temporal 3) if the proper criteria is met
and allows it to be synchronized with the NAC zone that it is connected.
Typical applications are sleeping rooms in hotels, guest suites, dormitories, day-care, residential boards
and care facilities as designated in NFPA 72.
CONSTRAINTS
1. SBGA-34 supervisory current is drawn from the detector loop in which their associated
detector is connected. This must be included in the determining the battery size of the panel.
2. SBGA-34 alarm current is drawn both from external power supply source and the detector
loop in which their associated detector is connected. Care must be taken to verify that this is
properly entered during its battery calculation requirements.
3. SBGA-34 audible section can be energized by an auxiliary power supply such as PS-35 with
AU-30U (System 3 power supply), PAD-3 / PAD 4 (Auxiliary Power Supply / NAC Extender) or
through the NAC circuit. The SBGA-34 can also be powered by a UL listed 24VDC Auxiliary
power supply/ Notification Appliance Circuit listed for fire protection signaling use.
4. The maximum number of SBGA-34 is related to the maximum current rating and power line
resistance of the auxiliary power supplies applied on the SBGA-34. Refer to the related
installation instructions of the auxiliary power supply. It is also related to the maximum current
rating of the loop. Refer to the installation instructions mentioned in the fifth constraint.
5. The maximum loop line resistance cannot exceed the maximum line resistance of the loop
driver the SBGA-34 is connected to specified in their respective installation instructions. For
Electrical Ratings
Voltage Rating 17 – 31VDC
Special Applications
Current Supervisory:
Loop: 0.6mA
External Power Supply:
0mA
Alarm:
Loop: 2.8mA
External Power Supply:
56mA
Audibility Measurements at 10 ft.
UL464 79dBA
UL268 85dBA
ULCS525 85dBA

the DLC module (XLS panel), refer to the DLC installation instructions, P/N 315-033090. For
the FCI2016-U1/FCI2017-U1 module (250pt/500pt Desigo/Cerberus panel), refer to the FS20
Installation Instructions, P/N A6V10315038. For the FC901MB-U1 (50pt Desigo/Cerberus
panel), refer to the FC360 Installation Instructions, P/N A6V10336754.
6. T-tapping of the notification appliance circuit is not allowed.
7. When SBGA-34 Is powered from external power supply source, care must be taken to insure
that proper ground fault detection is not compromised In typical application where the
external power source do not have the capability for ground fault detection, its ground
potential must be connected to the ground potential of the FACP to allow for ground fault
supervision.
8. A minimum of 14 AWG must be used.
9. Even though no specific spacing is allocated to the detectors used with this base, refer to
NFPA Standard 72 National Fire Alarm Code andthe installation instructions of the detector
being used (see Table 1).
For additional information on the used in an individual system, refer to the installationinstructions for that
particular module or contact your authorized Siemens Industry, Inc. representative.
DETECTOR PLACEMENT
The model SBGA-34 is compatible to the detectors listed in Table 1:
TABLE 1
COMPATIBLE DETECTORS
Detector Inst. Instr. P/N
HFP-11/HFPT-11 315-033290
HFPO-11 315-034800
SFP-11/SFPT-11* 315-033290C
SFPO-11* 315-033290C
8710, 8712, 8713 315-033290FA
FDO421 A6V10323926
FDOT421 A6V10323934
FDT421 A6V10323930
OP921 A6V10323928
OH921 A6V10323936
HI921 A6V10323932
FDOOT441 A6V10324655
FDOOTC441 A6V10324657
OOHC941 A6V10324661
OOH941 A6V10324659
*SFP-11, SFPT-11 and SFPO-11
detectors are approved for use in
Canada only.

DETECTOR WIRING
Refer to Figure 8. Audible Base Model SBGA-34 should be interconnected as shown in the
Installation/Wiring Diagrams as shown in figure 1-7 and wired to the specific system modules and control
panels following the appropriate instructions. For operation with Firefinder-XLS, FS250/FS250,
FC2025/FC2050, MP6000/7000, FC922/FC924, FC901/FC2005 systems, note any limitations on the
number of audible bases permitted on each notification appliance circuit, depending on the total cable
resistance for each audible sign circuit (See Electrical Ratings section).
5
6
7
8
TO NEXT SBGA-34, DB-11,
DB-3S or DB-X3RS
POWER SUPPLY
POLARITY SHOWN IN ACTIVE STATE
_+
SBGA-34
4
3
2
1
JUMPER FOR
TONE SELECTION
LINE 1 LINE 2
LINE 1 LINE 2
FROM P2 LOOP
NOTE: Use both Terminals (or leads) for connection, break wire run to provide electrical supervision
Figure 8
SBGA-34 Audible Base Terminal Blocks
TONE SELECTION
With audible base Model SBGA-34, the user can choose either temporal tone (Temporal 3 or Temporal 4)
or steady tone (Refer to figure 8).
For Temporal Tone: Terminal 3 and 4 are shorted (insert a jumper) Default setting is Temporal 3
To Select Temporal 4: Open the unit by unscrewing the DB-11 connected to the base
Move the J3 jumper to 2-3 position and refit the DB-11 to the base.
J3 Jumper
For Steady Tone: Terminals 3 and 4 are not connected (without a jumper)

P/N A6V10383428_a_en-- P/N A5Q00054382
8
NOTE 1: If the Audible Base is intended to follow the NAC coded outputs, the audible base must be set to
Steady Tone.
NOTE 2: Temporal 3 signal to be used for evacuation purposes only.
DETECTOR MOUNTING
The detector base comes from the factory prewired. All signaling and initiating circuits are connected
directly to the back of the SBGA-34 audible base using the four-position terminal blocks.
NOTE: The Audible Base Model SBGA-34 attaches only to a 4-inch square electrical box with extension.
Mounting the Base
1. Route all wires out from the outlet box.
2. Make connections directly to the audible base terminals located on the back of the base.
Refer to the related Installation/Wiring Diagram.
3. After all bases are installed, check loop continuity. For SBGA-34 Detector loop continuity
check, refer to the DPU or SDPU Manual, as applicable.
4. If loop continuity is acceptable, proceed with detector head installation.
BASE
MOUNTING
HOLES
MOUNTING
HOLE COVERS
ALARM LED
LOCATION WITH
DETECTOR
INSTALLED
IN BASE
6
5
D
O
N
O
T
P
A
I
N
T
Figure 9
SBGA-34 Top View