Siemens Synco living AP260 User manual

Page 1/11 Train the Trainer - August 2007
Door / Window Contact Smoke Detector
Synco living
Train the Trainer
Mounting
Safety Devices
August 2007

Page 2/11 Train the Trainer - August 2007
Door / Window Contact Smoke Detector
Mounting Auxiliary Equipment
Mounting the Door / Window Contact
Door / window contact AP 60
The door / window contact is su lied com lete with Installation Instructions,
battery, magnetic contact, and fixing material.

Page 3/11 Train the Trainer - August 2007
Door / Window Contact Smoke Detector
Mounting Auxiliary Equipment
Mounting the Door / Window Contact
Mounting location door / window contact AP 60
It is recommended to secure the RF sensor (C1)
to the door / window frame, and the magnet (C3)
directly to the edge of the door itself or the window‘s
wing.
It must be ensured that the SIEMENS logo on the
mounting late (C2) and that on the magnet (C3) are
aligned above one another and that the distance
between the magnetic late and the edge of the
door or window is a minimum of 3 mm and a maxi-
mum of 10 mm.

Page 4/11 Train the Trainer - August 2007
Door / Window Contact Smoke Detector
Mounting Auxiliary Equipment
Mounting the Door / Window Contact
Mounting location door / window contact AP 60
Prior to attaching the RF sensor (E1) to the mounting
late (E2), the transit tab (D4) at the rear of the RF sensor
in the battery com artment (D1) must be removed.
Place the RF sensor (E1) on the mounting late (E2)
and slide it in the direction of the arrow until it engages
in the catches (E3).
Function check
When o ening or closing the window or door, the LED briefly lights u twice.

Page 5/11 Train the Trainer - August 2007
Door / Window Contact Smoke Detector
Mounting Auxiliary Equipment
Mounting the Door / Window Contact
Removing door / window contact AP 60
For exam le, to re lace the battery of the door / window
contact, the RF sensor (H1) must be removed from its
mounting late. To do this, insert a tool (e.g. a small
screwdriver (H4)) into the slot between RF sensor (H1) and
mounting late (H2), ress the holding nose (H3) down
and slide the RF sensor (H1) to the left over the holding
nose out of its catches (H5).

Page 6/11 Train the Trainer - August 2007
Door / Window Contact Smoke Detector
Mounting Auxiliary Equipment
Mounting the Smoke Detector
DELTA reflex smoke detector
The DELTA reflex smoke detector is su lied com lete with Installation
Instructions, batteries, and fixing material.
Per room, maximum 1 DELTA reflex smoke detector can be fitted.

Page 7/11 Train the Trainer - August 2007
Door / Window Contact Smoke Detector
Mounting Auxiliary Equipment
Mounting the Smoke Detector
DELTA reflex smoke detector
To enable the DELTA reflex smoke detector to deliver an alarm via radio link,
it requires a smoke detector module M255.
+
DELTA reflex smoke detector Smoke detector module M255

Page 8/11 Train the Trainer - August 2007
Door / Window Contact Smoke Detector
Mounting Auxiliary Equipment
Mounting the Smoke Detector
Mounting location DELTA reflex smoke detector
When choosing the mounting location for the smoke
detector, the following oints must be observed:
Every smoke detector can cover an area of
max. 60 m2
Fit the smoke detector as close as ossible to
the center of the ceiling (minimum distance from
wall and corner: 15 cm)
In rooms with inclined or ointed ceilings, fit the smoke detector
a rox. 90 cm from the highest oint of the ceiling
In the case of rooms having a height of more than 3 m, several smoke
detectors are required (mounting height on the wall = 2.5 m)
Take air flows into account (de ending on the ty e of house)

Page 9/11 Train the Trainer - August 2007
Door / Window Contact Smoke Detector
Mounting Auxiliary Equipment
Mounting the Smoke Detector
Unsuited mounting locations for the DELTA reflex smoke detector
In rooms, where considerable amounts of water va or, dust or smoke
occur
In rooms with o en fire laces
In the vicinity of electrical fields (e.g. fluorescent energy saving lam s and
wiring, minimum distance: 50 cm)
At locations where ambient tem eratures dro below 0 °C or exceed
+50 °C

Page 10/11 Train the Trainer - August 2007
Door / Window Contact Smoke Detector
Mounting Auxiliary Equipment
Mounting the Smoke Detector
Inserting the smoke detector module
Removing the module‘s cover:
Insert a screwdriver in the res ective o ening
and ush it downward to lift the cover
Hold the smoke detector module at the edges,
insert it in its res ective lace and ush it
downward until the module‘s 2 lateral catches
engage
Re lace the cover to revent malfunctions
(caused by ressure variations or air drafts)