Siemens REV23.03RF User manual

CE1N2265en
22.02.2006
Building Technologies
HVAC Products
2265
REV23.03RF REV-R.03/1
REV23RF/SET
Self-learning Room
Temperature Controller REV23.03RF
Receiver REV-R.03/1
Consisting of controller (with integrated radio transmitter) and receiver
(switching unit with relay outputs)
•Mains-independent room temperature controller
•Straightforward, self-explanatory menu selection via roller selector
•Self-learning 2-position controller providing PID mode (patented)
•Choice of operating modes:
Automatic with maximum 3 heating or cooling periods, continuously comfort,
continuously economy, frost protection with one 24-hour operating mode including
one heating or cooling period
•In automatic mode, one temperature setpoint can be entered for each heating or
cooling period
•Optional control of cooling equipment
•Advantageous for retrofitting and upgrading projects
(wireless room unit)
Use
For control of the room temperature in:
•Apartments, single-family or holiday houses
•Offices, individual rooms, consulting rooms or commercially used spaces
For control of the following pieces of equipment:
•Solenoid valves of instantaneous water heaters

2/17
Building Technologies Raumtemperaturregler REV23.03RF CE1N2265en
HVAC Products 22.02.2006
•Solenoid valves of atmospheric gas burners
•Forced draft gas or oil burners
•Circulating pumps of heating systems, zone valves
•Electric direct heating systems or fans of electric storage heaters
•Thermal actuators
•Cooling and refrigeration equipment
Functions
•Radio signal transmission
•PID control with self-learning or selectable switching cycle
•2-position control
•Automatic mode with 7-day switching program for 24-hour, working day, weekend or
7-day operation with up to 3 heating or cooling periods per day
•Each heating or cooling period has its own temperature setpoint
•One 24-hour operating mode with one heating or cooling period
•Override button
•Sensor calibration and reset function
•Frost protection or overtemperature protection
•Limitation of the minimum setpoint
•Holiday mode
•Heating or cooling mode
•Periodic pump run
•Optimum start control with the first heating period
Type summary
Radio signal equipment consisting of:
Room temperature controller (transmitter), receiver (switching unit)
and support REV23RF/SET
Room temperature controller (transmitter) and support REV23.03RF
Receiver (switching unit) REV-R.03/1
Ordering
When ordering, please give the type references according to «Type summary».
The controller / transmitter REV23.03RF is supplied complete with batteries.
Technical design
Display and
operating elements

3/17
Building Technologies Raumtemperaturregler REV23.03RF CE1N2265en
HVAC Products 22.02.2006
Operating elements
Selection of operating mode (see below)
«Warmer» button
«Colder» button
Override button (see below)
Roller selector for the menu, submenu and the settings
Confirm by pressing
Leaving the current menu level and returning to the menu level
previously active (settings currently displayed will be ac-
cepted)
Displays
Time of day
° C
Room temperature
Change batteries (display appears about 3 months before bat-
teries are exhausted)
Holiday mode active
Selection of operating mode (only one operating mode active)
Automatic mode
Comfort mode
Economy mode
Frost protection or overtemperature protection
24-hour mode with one heating or cooling period
(heating or cooling period is individually adjustable)
Temporary change of the current setpoint temperature
(change only active until the next switching point is reached)
° C
Press the + or – button once to display the adjusted tempera-
ture setpoint. It can be readjusted in increments of 0.2 °C (max.
+/- 4 °C)
Override button
In operating modes and , this button can be used to manually switch
from comfort to economy temperature, or vice versa. The selection is automati-
cally reset when the next switching point is reached or when the operating
mode is changed

4/17
Building Technologies Raumtemperaturregler REV23.03RF CE1N2265en
HVAC Products 22.02.2006
Menu-driven user settings: 4 main menus are available
Time of day and weekday Main menu Submenu Settings
hCurrent time
Current weekday
Temperature Main menu Submenu Default settings – heating / cooling
T Setpoint of comfort mode 19 °C 23 °C
Setpoint of economy mode 16 °C 29 °C
Setpoint frost or
overtemperature protection 5 °C 35 °C
Setpoint remote operation is
not used with this unit (10 °C) (30 °C)
Time switch Main menu Submenu Settings
Selection of weekday, working day,
weekend or week
Selection of the number of heating
or cooling periods (max. 3 periods
per day)
h
Selection of the heating / cooling period’s start and end time
° C
T
Selection of the heating / cooling period’s temperature setpoint
Absence Main menu Submenu
Entry of holidays or periods of absence. Number
of days with economy mode setting / max. 99
days
Temperature setpoint during absence.
Default setting is 12 °C for heating and 30 °C for
cooling

5/17
Building Technologies Raumtemperaturregler REV23.03RF CE1N2265en
HVAC Products 22.02.2006
Menu-driven heating
engineer settings Menu items Settings
CAL Sensor calibration
Setpoint limitation
Optimum start control for the first heating period
(in unit of time per 1 °C)
2-position control
PID mode, self-learning
PID mode, switching cycle 6 or 12 minutes
/Periodic pump run off / on
Heating / cooling mode
In automatic operating modes, the temperature setpoints can be individually adjusted
for every comfort period and for the continuous operating modes. The temperature
setpoint of economy mode is the same in automatic and continuous operation.
In frost or overtemperature protection mode, the room temperature is constantly moni-
tored. If it falls (rises) below (above) the adjusted setpoint, control to the adjusted frost
or overtemperature protection setpoint will be ensured.
The controller operates in 24-hour operating mode according an individually adjustable
24-hour program with 1 heating / cooling period.
To adjust heating / cooling period, select 24-hour operating mode and adjust time pro-
gram and desired temperature setpoint by roller selector.
24-hour operating mode is maintained until another operating mode is selected.
The switching program can be used as a 7-day or 24-hour program, depending on
programming. It is also possible to select one of the continuous operating modes
with which the switching program is not used.
With the 7-day program, all individual days, working days (1-5), weekend (6-7), or the
entire week (1-7) can be programmed.
For each heating / cooling period, 3 different switching patterns are available.
There is a choice of 1, 2 or 3 heating / cooling periods. For each heating / cooling pe-
riod, the start time, end time and comfort setpoint are to be entered.
In between heating / cooling periods, it is always the same economy temperature set-
point that is used. This economy temperature setpoint can be adjusted on the tempera-
ture menu.
Temperature
setpoints
Protective function
24-hour operating
mode
Switching program

6/17
Building Technologies Raumtemperaturregler REV23.03RF CE1N2265en
HVAC Products 22.02.2006
2261Z02
16
°C
18
20
22
08 10 18 22 h
Heizphase 1
Heizphase 2
The holiday function is to be selected on the user menu. Set the start of the holiday
period (day of departure / /weekday), the duration of the holiday period and
the temperature setpoint ( ). This will enable the controller to maintain the adjusted
temperature for a period of up to 99 days. Every day at midnight, the counter subtracts
one day.
When the holiday period is over, the counter reads 00, and the controller will automati-
cally resume the operating mode selected last.
To be flexible, the REV23.03RF has no connection facility for remote operation.
Switching times Temperatures in ° C
1st
period
2nd
period
3rd
period
Oper-
ating
mode
Block /
week-
days 1st period 2nd period 3rd period
Auto
1-5
Mo-Fr
6-7
Sa-Su
06:00
07:00
08:00
23:00
11:00 13:00 17:00 22:00
19
19
23
23
20
23
21
23
16
16
29
29
1-7
Mo-Su 00:00 24:00 19 23
1-7
Mo-Su 00:00 24:00 16 29
1-7
Mo-Su 00:00 24:00 5 35
1-7
Mo-Su 07:00 23:00 19 23
Absence 12 30
Setpoint limitation
Control mode 2-Point control
Optimum start control OFF
Periodic pump run OFF
Heating active
Example with 2 heating
periods per day
Holiday function
Remote operation
Factory settings
Factory settings
Heating engineer level

7/17
Building Technologies Raumtemperaturregler REV23.03RF CE1N2265en
HVAC Products 22.02.2006
Heating engineer level
To access the heating engineer level, keep the «Warmer» and «Colder» buttons de-
pressed and simultaneously roll the roller selector away from the display and then to-
ward the display.
If the displayed temperature does not agree with the room temperature effectively
measured, the temperature sensor can be recalibrated (recalibration to be made on the
heating engineer level.)
The displayed temperature can be matched to the effective room temperature in incre-
ments of 0.2 °C (max. ± 2 °C).
Minimum setpoint limitation to 16 °C prevents undesired heat transfer to neighboring
apartments in buildings with several heating zones. The setting is to be made on the
heating engineer menu.
Optimization brings forward the switch-on point of the first heating period such that the
adjusted setpoint will be reached at the required time.
The setting depends on the type of controlled system, that is, on heat transmission
(type of piping system, radiators), building dynamics (building mass, insulation), and
heat output (boiler capacity, flow temperature).
Optimum start control is switched off at
t
T
17
18
19
- 4 - 2
2264D03
16
- 3
1/4h/°C
1/2h/°C
1h/°C
Start
- 2 - 1 - ½
- 1½
- 1 - ½ - ¼
- ¾
Pon
20
°C
- 1 h
h
h
TRx
h
h
h
h
h
h
h
h
h
1st heating period
(slow controlled system)
(medium controlled system)
(fast controlled system)
(no impact)
Optimum start controll Off
T
T Temperature (°C) TRxActual valve of room temperature
t Forward shift of switch-on point (h) Pon Starting point of optimum start control
REV23.03RF is a 2-position controller providing PID mode. The room temperature is
controlled by the cyclic switching of an actuating device.
The controller generates the positioning signals depending on the deviation of the set-
point from the actual value acquired by the built-in temperature sensor.
The rate of response to the deviation depends on the selected control algorithm:
The controller is supplied with an active self-learning mode, enabling it to automatically
adapt to the type of controlled system (building construction, type of radiators, size of
the rooms, etc.). After a certain learning period, the controller optimizes its parameters
and then operates with the parameters it has learned.
PID 12 mode Switching cycle of 12 minutes for normal or slow controlled systems
(massive building structures, large spaces, cast-iron radiators, oil
burners).
PID 6 mode Switching cycle of 6 minutes for fast controlled systems (light building
structures, small spaces, plate radiators or convectors, gas burners).
2-Pt mode Pure 2-position control with a switching differential of 0.5 °C (±0.25 °C)
for very difficult controlled systems with considerable outdoor tempera-
ture variations.
For easy commissioning controller is set to 2-Point mode as factory
setting.
Access
Sensor calibration
CAL
Setpoint limitation
Optimum start control
Example using an actual
room temperature of 18 °C
and a setpoint of 20 °C
Control
Self-learning mode

8/17
Building Technologies Raumtemperaturregler REV23.03RF CE1N2265en
HVAC Products 22.02.2006
Protects the pump against seizing during longer off periods. Periodic pump run is acti-
vated for one minute every 24 hours at midnight. This function can be selected on the
heating engineer menu.
Periodic pump run active: / periodic pump run inactive:
The controller is suited for cooling applications.
The function can be selected on the heating engineer menu.
The controller comes set for heating operation (refer to section «Factory settings»).
User-defined data:
Press the button behind the pin opening for at least one second: This resets the user-
specific settings to their default values (heating engineer settings will not be changed).
The clock starts at 12:00. During the reset time, all sections of the display are lit, ena-
bling them to be checked.
All user-defined data plus the heating engineer settings:
Press the button behind the pin opening together with the warmer and colder buttons
for at least one second.
After the reset, all factory settings will be reloaded (also refer to section «Factory
settings»).
Mechanical design
The REV23.03RF has a plastic housing with a large display and easily accessible op-
erating elements. The controller is removed from its base by sliding it upward. It is thus
possible to replace the two type AA 1.5 V alkaline batteries contained in the compart-
ment at the rear of the controller.
About 3 months before the batteries are exhausted, battery symbol appears on
the display, but all functions are fully maintained. When replacing the batteries, the
current data will be retained for a maximum of one minute.
Plastic housing with easily accessible operating elements and removable cover. The
unit can be fitted to all commercially available recessed conduit boxes or directly on the
wall. A relay with a potential free changeover contact, the connection terminals and the
receiving antenna are integrated in the housing.
The base can be fitted to most types of commercially available recessed conduit boxes
or directly on the wall.
The support supplied with the controller enables the unit to be put on a shelf. It can be
easily fitted to the controller with no need for tools.
Periodic pump run
/
Operating mode
Heating / cooling
/
Controller
Battery change
Receiver
REV-R.03/1
Base
Support

9/17
Building Technologies Raumtemperaturregler REV23.03RF CE1N2265en
HVAC Products 22.02.2006
Notes
•The room unit should be located in the main living room (on the wall or free-standing
using the support provided) while giving consideration to the following points:
•The distance to the receiver should not exceed 20 m or 2 floors
•The unit should be located such that the sensor is able to capture the room tempera-
ture as accurately as possible, without getting affected by direct solar radiation or
other heat or refrigeration sources (in the case of wall mounting, about 1.5 m above
the floor)
•The unit should be located such that it can transmit signals with as little interference
as possible. For this reason, the following points should be observed:
−Do not mount the unit on metal surfaces
−Not in the vicinity of electrical cables and equipment such as PCs, TV sets, mi-
crowave appliances, etc.
−Not in the vicinity of large metal structures or construction elements with fine
metal meshes like special glass or special concrete
•The control mode can be changed via the menu-driven heating engineer settings.
•If the room temperature displayed does not agree with the room temperature effec-
tively measured, the temperature sensor should be recalibrated (refer to «Calibration
of sensors»).
•In the case of wall mounting, ensure that there is sufficient clearance for removing the
controller from its base, and for replacing it
First, fit the base. Then, engage the controller from the top. The base can be fitted to
most commercially available recessed conduit boxes or directly on the wall
min.
10 cm
2261Z03
•Refer to the Installation Instructions printed on the package.
•The receiver and switching unit should preferably be mounted near the controlled
device
•The unit should be located such that it can receive signals with as little interference
as possible. For this reason, the following points should be observed (same as with
the transmitter):
−Not in control panels
−Not on metal surfaces
−Not in the vicinity of electrical cables and equipment such as PCs, TV sets, mi-
crowave appliances, etc.
−Not in the vicinity of large metal structures or construction elements with fine
metal meshes like special glass or special concrete
•The location where the unit is mounted should be dry and free from splash water
•The unit can be fitted to most commercially available recessed conduit boxes or di-
rectly on the wall
Planning
controller / transmitter
REV23.03RF
Wall mounting of
controller / transmitter
REV23.03RF
Support of
REV23.03RF
Planning
Receiver
REV-R.03/1

10/17
Building Technologies Raumtemperaturregler REV23.03RF CE1N2265en
HVAC Products 22.02.2006
The receiver must be wired with the power supply switched off.
Mains voltage may be switched on again only after the unit is completely
mounted.
•When mounting the unit, the base must first be fitted and wired (L/N = AC 230 V
mains supply, LX/L1 = consumers). Then, engage the unit at the top, swing it down-
ward and secure it with a screw
•For more detailed information, refer to the Installation Instructions supplied with the
unit
For the electrical installation, the local safety regulations must be complied with.
•Remove the battery transit tab: As soon as the battery transit tab is removed, the
unit starts to operate.
•If possible, mount receiver temporarily in a first run (e.g. double coated tape). Doing
that, location of best RF reception can be identified later on. See clause “5 Find lo-
cation of best reception“
•Completely wire and mount REV-R.03/1 temporarily (please also close front cover)
a) Switch on power at REV-R.03/1: LED_1 lights always in red or flashes in red
b) Press the "RESET“ button on REV-R.03/1 for about 4 seconds: The orange LED_2
will flash very fast and briefly (stored address of REV23.03RF will be erased)
c) Press the "SET“ button (set / learn) for about 3 sec. until the orange LED_2 starts
flashing slowly and continuously: Receiver is now in learning mode
d) The receiver stays max. 25 minutes in learning mode. If no learning telegram from
REV23.03RF is received during that period of time, repeat steps b) and c) again
e) Press the ESC button on REV23.03RF for about 4 seconds. Learning tele-
gram is transmitted
f) If REV-R.03/1 receives learning telegram, the orange LED_2 flashes fast and
briefly
g) If the orange LED_2 is steady on, the relay is energized (= controlled device ON)
h) If the orange LED_2 is dark, the relay is deenergized (= controlled device OFF)
i) Depending on the operating state, REV23.03RF repeats the ON or OFF control
telegram every 3 minutes. With this the relay will be switched ON or OFF according
to control telegram latest after 3 minutes
j) If REV-R.03/1 does not receive any correct control telegram within 60 minutes,
controlled device is being switched off and LED_1 flashes in red
k) In the event of a power failure at the REV-R.03/1, the relay will be deenergized.
Mounting and
installation of receiver
REV-R.03/1
Commissioning
controller/transmitter
REV23.03RF
and receiver
REV-R.03/1
1. Switch on
REV23.03RF
2. Mount REV-R.03/1
temporarily
3. Link REV-R.03/1
with REV23.03RF
Override button and
test telegram
ESC button and
learnin
g
tele
g
ram
LED_1 (green / red):
Indication for
- Signal strength
- Receiver linked to
cotroller/transmitter
LED_2 (orange):
Indication for
- Learning mode
- Telegram reception
- Status of relais contact
SET button
RESET button