Siemens ATI510 User manual

Building Technologies
Fire Safety & Security Products
ATI5100
Intrusion Arming Terminal
Installation

Technical specifications and availability subject to change without notice.
© 2009 Copyright Siemens Switzerland Ltd
We reserve all rights in this document and in the subject thereof. By acceptance of the document the recipient acknowledges these rights
and undertakes not to publish the document nor the subject thereof in full or in part, nor to make them available to any third party without our
prior express written authorization, nor to use it for any purpose other than for which it was delivered to him.

3
Building Technologies 020_ATI5100_A6V10235012_a_en
Fire Safety & Security Products 23.09.2009
1About this document ....................................................................................4
2Safety..............................................................................................................5
2.1 Target Group...................................................................................................5
2.2 General Safety Precautions............................................................................5
2.2.1 General Information.........................................................................5
2.2.2 Transport..........................................................................................5
2.2.3 Installation........................................................................................5
2.2.4 Service and Maintenance................................................................6
3Standards and Guidelines............................................................................6
3.1 EU-Directives ..................................................................................................6
3.2 FCC.................................................................................................................6
3.3 C-Tick..............................................................................................................7
3.4 UL-Directives...................................................................................................7
4Technical Data...............................................................................................7
4.1 Recommended Cable Specifications..............................................................8
5Details for Ordering ......................................................................................9
6Package Contents.........................................................................................9
7Description of Equipment ............................................................................9
7.1 Service Description.........................................................................................9
7.2 Product overview...........................................................................................10
7.3 Set Jumpers..................................................................................................11
8Installation ...................................................................................................12
8.1 Opening the housing.....................................................................................12
8.2 Connecting cables.........................................................................................13
8.3 Mounting the base.........................................................................................13
8.4 Mounting the cover........................................................................................14
8.5 Programming and firmware download..........................................................14
9Disposal .......................................................................................................15
Table of contents

About this document
4
Building Technologies 020_ATI5100_A6V10235012_a_en
Fire Safety & Security Products 23.09.2009
1About this document
This document contains information on the installation of the product.
For information on usage refer to the user manual. For information on configuration
refer to the SiPass integrated user manual.
Contacting us
If you have questions or suggestions regarding the product or this documentation,
please contact our Customer Support Center:
Intranet: Customer Support Center
Internet: Worldwide contacts
Email: [e-mail]
Tel.: [phone]
Training courses
Siemens Building Technologies Fire Safety & Security Products provides training
courses for all products.

Safety
5
Building Technologies 020_ATI5100_A6V10235012_a_en
Fire Safety & Security Products 23.09.2009
2Safety
2.1 Target Group
Target
readers
Qualification Activity Condition of the
product
Installer Technical training for
electrical installations.
Installs the product,
individual components
of the product or
replacement parts.
Components of the
product are not yet
installed or need to be
replaced or modified.
2.2 General Safety Precautions
2.2.1 General Information
Read the general safety precautions before installing/configuring/operating the
device.
Keep this document for reference.
Always pass this document on together with the product.
Liability claim
Use only spare parts and accessories that have been approved by the
manufacturer.
Danger of electrical shock on the open device
Only qualified personnel should open the unit.
2.2.2 Transport
Damage during transport
Keep the packaging material for future transportation.
Do not expose the device to mechanical vibrations or shocks.
2.2.3 Installation
Refer installation to a qualified electrician.
When handling modules that are susceptible to electrostatic discharge, please
observe the ESD guidelines.
Damage due to unsuitable mounting location

Standards and Guidelines
6
Building Technologies 020_ATI5100_A6V10235012_a_en
Fire Safety & Security Products 23.09.2009
The environmental conditions recommended by the manufacturer must be
observed.
The device should only be used for indoor applications.
Connect the device only to power sources with the specified voltage. Voltage
supply requirements can be found on the rating label of the device.
Protect the device against moisture.
2.2.4 Service and Maintenance
Do not attempt to service or modify this device yourself. Refer this work to
qualified service personnel.
3Standards and Guidelines
3.1 EU-Directives
This product complies with the requirements of the following European directives.
The EU declaration of conformity is available to the responsible agencies at:
Siemens Building Technologies
Fire & Security Products GmbH & Co. oHG
76181 Karlsruhe
Germany
European Directive 2004/108/EC „Electromagnetic Compatibility”
Compliance with the European Directive 2004/108/EC has been proven by testing
according to the following standards:
Emitted interference: EN 55022 class B
Interference resistance: EN 50130-4
3.2 FCC
This equipment complies with the FCC Rules CFR 47 Part 15 Emission Class B
limits.
This equipment has been tested and found to comply with the limits for a Class B,
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turnings the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
Reorient or relocate receiving antenna.

Technical Data
7
Building Technologies 020_ATI5100_A6V10235012_a_en
Fire Safety & Security Products 23.09.2009
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
3.3 C-Tick
Standard for Australia and New Zealand (equivalent to EN 55022 of European
Directive)
3.4 UL-Directives
UL 294 Access control units, not UL evaluated for Household or Commercial
Burglary.
4Technical Data
ATI5100
Tamper contact Integrated in housing
Display LC: 128 x 64 dots
4 lines with 16 characters per line
Operating voltage 9 to 30 VDC
Current consumption 35 to 82 mA @ 12 V
Operating temperature 0 to +50 °C
Relative humidity 93 % (no dew)
Buzzer Integrated
Sound level: Different settings for alarms and key press
Housing Polycarbonate
IP rating IP30
Colour RAL 9003
Weight 0.38 kg
Dimensions (W x H x D) 112 x 185 x 28 mm
Please note that the ATI5100 is not intended for use with Intrunet SI400 series
(previously known as Sintony) intrusion systems.

Technical Data
8
Building Technologies 020_ATI5100_A6V10235012_a_en
Fire Safety & Security Products 23.09.2009
4.1 Recommended Cable Specifications
NOTICE
Guideline for selecting cables
The table provides a guideline for selecting an appropriate cable type only.
Other cable types are also compatible with the system and can be used to
achieve the same results.
Recommended Cable Specifications Communica-
tion Type Cores Pairs AWG Cores J-Y(St)Y
Diameter
(mm)
Wire
Type
Insulation Shield Jacket
5 2
6 3
RS485
8 4
28 7 x 36 0.6 Tinned
Copper
Foam
Polyethylene
Aluminium foil -
Polyester tape /
braided shield
PVC
4 2
6 3
RS232
8 4
24 7 x 32 0.6 Tinned
Copper
Foam
Polyethylene
Aluminium foil -
Polyester tape /
no braid
PVC
4 2
6 3
RS422
8 4
24 7 x 32 0.6 Tinned
Copper
Foam
Polyethylene
Aluminium foil -
Polyester tape /
no braid
PVC
8 4 Solid Bare
Copper
RJ45
8 4
24
7 x 32
0.6
Tinned
Copper
Polyethylene Unshielded PVC
8 4 Solid Bare
Copper
RJ12
8 4
24
7 x 32
0.6
Tinned
Copper
Polyethylene Aluminium foil -
Polyester tape /
no braid
PVC
Power (12/24
V DC)
2 1 18 19 x 30 1.0 Tinned
Copper
Foam
Polyethylene
Unshielded PVC

Details for Ordering
9
Building Technologies 020_ATI5100_A6V10235012_a_en
Fire Safety & Security Products 23.09.2009
5Details for Ordering
Type Part no. Designation Weight
ATI5100 S24246-F2605-A1 Intrusion Arming Terminal 0.38 kg
6Package Contents
1 x ATI5100
1 x Installation manual
Accessories pack
7Description of Equipment
7.1 Service Description
The ATI5100 is an intrusion arming terminal that operates as a part of an
integrated access control and security system. The ATI5100 provides a local
interface between an advanced access controller (ACC) and the cardholder, to arm
and disarm alarm areas.
The following diagram displays where the ATI5100 fits in the SiPass integrated
architecture.
FLN Bus - RS485
FLN Bus - RS485
ATI5100
DC12 DC22
DRI
DRI IPMIPM
Exit
Reader
Ent r y
Reader
ATI5100 in the SiPass integrated system

Description of Equipment
10
Building Technologies 020_ATI5100_A6V10235012_a_en
Fire Safety & Security Products 23.09.2009
7.2 Product overview
E
F3 EOL A
B
I
G
F1
X3
D
F2
A
K2 K3
CH
K1 L
Product overview
A Lugs G Screws for mounting
B Printed circuit board H Screw for tamper contact
C Screw terminal I Cable duct
D Tamper switch K1-K3 Breakout pieces
E Fixing screw for printed circuit board L Cable entry hole
EOL Jumper X3 Jumper
F1-F3 Lugs holding the PCB

Description of Equipment
11
Building Technologies 020_ATI5100_A6V10235012_a_en
Fire Safety & Security Products 23.09.2009
7.3 Set Jumpers
Jumper Description Value
EOL EOL TERMINATION (FLN System Bus)
This link allows the RS485 bus communication channel to be terminated in lengthy
comms lines – more than 100 m.
EOL
X3 (1-2) Reset the ATI5100 retaining the unit’s firmware
Interrupt the power supply to the unit for 1 sec.
or
Close X3 (1-2).
2
1

Installation
12
Building Technologies 020_ATI5100_A6V10235012_a_en
Fire Safety & Security Products 23.09.2009
8Installation
8.1 Opening the housing
1. Loosen the screws by a couple of turns.
Open unit
2. Push the lugs downwards and slightly lift the cover using a screwdriver.
3. Lift the cover by approx. 2 cm and push it upwards.
Unit is opened

Installation
13
Building Technologies 020_ATI5100_A6V10235012_a_en
Fire Safety & Security Products 23.09.2009
8.2 Connecting cables
It is recommended to use a cable type IYSTY (Twisted Pair) 2 x 2 x Ø 0.6 mm or
larger diameter.
1. Insert the cable through the cable entry hole [ 10] in the base.
2. If necessary, carefully remove the breakout pieces [ 10] .
3. Connect the individual wires to the screw terminals.
Connections
Contact pin Abbreviation Function
1 A/+ RS485
2 B/- RS485
3 + + Vin
4 - - Vin
5 to 10 Not connected
Attach the cable with a cable tie.
Cable tie
8.3 Mounting the base
Make sure to mount the unit only on surfaces that are sufficiently hard and rigid.
1. Mark 3 holes for the mounting screws [ 10] and one for the tamper contact
[ 10] .
2. Drill the holes and screw the base.

Installation
14
Building Technologies 020_ATI5100_A6V10235012_a_en
Fire Safety & Security Products 23.09.2009
8.4 Mounting the cover
1. Hook the top of the cover into the base and push downward.
2. Push back the upper part of the housing.
3. The two lugs on the base engage with the corresponding recesses in the cover.
4. Tighten the two screws at the bottom of the unit and seal them using the
supplied seals.
Close unit
8.5 Programming and firmware download
The ATI5100 is programmed using SiPass integrated software, via the AC5100, or
using the standalone FLN Configurator application. Please refer to the appropriate
User’s Manual for more information.

Disposal
15
Building Technologies 020_ATI5100_A6V10235012_a_en
Fire Safety & Security Products 23.09.2009
9Disposal
All electrical and electronic products should be disposed of
separately from the municipal waste stream via designated
collection facilities appointed by the government or the local
authorities.
This crossed-out wheeled bin symbol on the product means the
product is covered by the European Directive 2002/96/EC.
The correct disposal and separate collection of your old appliance
will help prevent potential negative consequences for the
environment and human health. It is a precondition for reuse and
recycling of used electrical and electronic equipment. For more
detailed information about disposal of your old appliance, please
contact your city office, waste disposal service or the shop where
you purchased the product.

Issued by
Siemens Building Technologies
Fire & Security Products GmbH & Co. oHG
Siemensallee 84
D-76181 Karlsruhe
www.buildingtechnologies.siemens.com
© 2009 Copyright Siemens Switzerland Ltd
Technical specifications and availability subject to change without notice.
Document ID A6V10235012
Edition 08.12.2009