Sierra Wireless Raven XE User manual

CoverTitle
Raven XE
Quick Start Guide
for AT&T
20080617
Rev 1.0 B

Rev 1.0 B Mar.10 23
Raven XE Quick Start Guide
This Quick Start guide provides brief overview of the steps required
to activate your Raven XE on AT&T’s network.
Tip: For additional configuration options, refer to the User Guide for your
device.
H
Requirements
• Cellular Account Required- To use your modem, you need to
have a SIM with an active account in a data plan, with your
cellular provider (EDGEor HSUPA/HSDPA).
• ACEmanager - Graphical interface for software configuration.
You can download ACEmanager from the Sierra Wireless AirLink
Solutions website: http://www.sierrawireless.com/support/. A
default installation of this utility is assumed later in these direc-
tions.
• Ethernet cable - An Ethernet cable is required.
Note: Until you install a driver for the USB port, you cannot use your USB
port to configure the modem.
• Power adapter and a power source - You will need a power
supply and power source for the modem.
• PC or laptop - To configure the modem, you will need a
computer with an available serial port.
• Small Phillips screw driver - The Phillips screw driver is the one
which is also called a plus (+) or X screw driver.
Note: Most accounts use
the default addressing
solution of Private or
Public IP addresses
supplied by the Internet
and Proxy APNs. Only if
you have a Static or
Custom IP address should
you need to configure a
custom APN.
Warning: The antenna should be installed no closer than
20 cm from the human body. It is one of the RSS-102
requirements for devices not requiring SAR.
Note: Raven XE I/O Port 4 is software configurable.

Raven XE
24 20080617
Connecting the Raven XE
GSM Networks
1. INSERT SIM. Using a small phillips head screw driver, remove the screws on
the front of the Raven XE. Carefully remove the SIM card from the card you
received from AT&T. Gently press the SIM card to click it in to place. When
the faceplate is replaced and secured, the installation of the SIM is complete.
Tip: The top of the card faces the bottom of the modem.
2. CONNECT ANTENNAS. Install cellular antenna and the reverse diversity
antenna situated on the back panel of the device.
3. CONNECT TO A COMPUTER OR OTHER DEVICE: The Ethernet port of
your Raven XE can be connected directly to a computer or other Ethernet
device with either a cross-over cable or a straight-through cable.
4. CONNECT USB: Your Raven XE’s full-speed (12 Mbit) USB 2.0 port can be
connected directly to most computers or other devices using a standard full-
speed USB 2.0 cable.
5. POWER ON. Your Raven XE can be used with either DC or AC, with the
appropriate power adapter. DC cables and AC adapters are available as
optional accessories in addition to the one included with your Raven XE. The
Raven XE digital I/O port consists of a 4 pin power connector, which includes
two digital I/O ports. Port 4 is software configurable, while port 3 is Digital
Input only and not software configurable.
6. CONFIGURE APN. If you have a custom APN or an active SIM outside the
US, request the APN details from your carrier and configure them with
ACEmanager.
7. CONFIGURE IN ACEmanager. To start and configure your Raven XE, enter
http://192.168.14.31:9191/index.htm on your browser.
The default login credentials are:
•Login: user
•Password: 12345

Rev 1.0 B Mar.10 25
Note: Users can configure
their APN confgiuration on
the WAN/Cellular tab.
Note: Explosion Hazard -
Substitution of any compo-
nents may impair suitability
for Class I, Division 2.
Specifications
Interface Raven XE Connected Device
Ethernet Private default 192.168.13.31* 192.168.13.100
USB/NET 192.168.14.31 192.168.14.100
DUN 192.168.15.31 192.168.15.100
Approvals FCC, Industry Canada, RoHS,Carrier specific approvals, PTCRB
Network
compliance HSUPA
With Fallback to:HSDPA; UMTS; EDGE; GPRS (MS-12); GSM
Embedded
Module MC5727
Voltage range 9–28VDC
Reverse polarity
protection Compliant
Current draw Transmit (Typical/Max) 110/265 mA
Idle 80 mA
Input Current 75 mA to 265 mA
Input Voltage 9 - 28V DC