Signature Hardware CALHOUN 927746 User manual

11.800.855.2284
CALHOUN
SHOWER SYSTEM
SKU: 927746
REVISED 02/02/2021
CODES: 405441, 414750, 414751
GETTING STARTED
BEFORE YOU BEGIN
We recommend consulting a professional if you are

Hardware accepts no liability for any damage to the
faucet, plumbing, sink, counter top, or for personal
injury during installation.
Observe all local plumbing and building codes.
Unpack and inspect the product for shipping damage.
If any damage is found, contact our Customer
Relations team via live chat at www.signaturehard-
ware.com or by emailing support@siganturehard-
ware.com.
Ensure that you have gathered all the required
materials that are needed for the installation.
Plumbers Tape
Phillips Screwdriver
ADDITIONAL QUESTIONS?
Still need help? Check out our Help Center at
www.signaturehardware.com for product and
warranty information, or contact us through live
chat or by emailing support@signaturehard-
ware.com.
TOOLS AND MATERIALS:
Pencil Drill
Level Tape Measure

21.800.855.2284
1. Select the appropriate installation type for your
application.
INSTALLATION
G½"
G½"
1-3
/
16"-2-3
/
16"
G½"
2-G½"
2-G½"
45-¼" 55-1
/
8"
¾"
G½"
Finished Floor
OUT
HOT WATER
IN
COLD WATER
IN
OUTOUT
Rough
Wall
Channel
Rough
Wall
For stud walls, install the valve
body between the studs behind

For masonry walls, create a
channel for valve body and pipe
installation.
CALHOUN
SHOWER SYSTEM
SKU: 927746

31.800.855.2284
2. For stud wall installation, wrap plumbers tape around
the threaded connections and attach to the valve
body. For masonry wall installation, move on to step 24
(page 9)
3. Wrap plumbers tape around the threaded portion of
the plugs and attach to the shower holder.
4. Determine the locations of the valve body and
shower head. Connect the inlet pipe to the inlet joint.
Install the 90° female elbow in thehand-shower holder
location.
Straight Connector
Valve Body
90° Elbow
Plumbers Tape
Shower Holder
Plug
Keep in Line
90° Female Elbow
Keep in Line
Hot Water
Inlet Cold Water
Inlet
CALHOUN
SHOWER SYSTEM
SKU: 927746

41.800.855.2284
5.Mark the location of the mounting holes on the
shower holder in the installation location. Use a level to
ensure the holder is aligned properly.
6. Drill mounting holes with the appropriate drill bit.
7. instert wall anchors into the holes drilled in the
previous step.
8. Loosely attach the shower holder to the wall with
self-tapping screws.
Level
Pencil
1-7
/
8"
1-7
/
8"
4-ø 8 Holes
Drill
Self-Tapping Screw
Philips Screwdriver
CALHOUN
SHOWER SYSTEM
SKU: 927746

51.800.855.2284
9. Tighten the self-tapping screws after making
adjustments.
10. Mark the location of the mounting holes on the
valve body in the installation location. Use a level to
ensure the holder is alighned properly.
11. Drill mounting holes with the appropriate drill bit
and insert the wall anchors.
12. Loosely attach the valve body.
Level 4-ø 8 Holes
CALHOUN
SHOWER SYSTEM
SKU: 927746

61.800.855.2284
13. Tighten the screws after making adjustments.

to clear out any dirt and debris.
15. Connect the inlet pipes. Wrap plumblers tape
around the threaded portion of the plug. Insert the
plug into the 90° female elbow.
16. Remove the protective sheath and run water to
test the pressure and ensure there are no leaks.
Hot Water Inlet
Cold Water Inlet
Plug
Hot
Water
Inlet Cold Water Inlet
Cartridge
Closed
Cartridge
Open
Switch to diverter
each step
Diverter
Cartridge
Protective
Sheath
CALHOUN
SHOWER SYSTEM
SKU: 927746

71.800.855.2284
17. Place the protective sheath back on the valve body
and shower holder.
18. Place the u-shaped bracket on the reinforcing rod
and mark the location of the mounting holes.
19. Drill mounting holes with the appropriate drill bit.
Protective Sheath
U-shaped Bracket
Reinforcing Rod
2-ø 8 Hole
CALHOUN
SHOWER SYSTEM
SKU: 927746

81.800.855.2284
20. Insert anchors into the holes drilled in the previous
step.
21. Attach the bracket to the wall with self-tapping
screws.

CALHOUN
SHOWER SYSTEM
SKU: 927746

91.800.855.2284
23. Remove the protective sheath and unscrew the
plugs. Move on to step 44 (page 14)
24. For masonry wall installation, wrap plumbers tape
around the threaded connections and attach to the
valve body.
25. Wrap plumbers tape around the threaded
connections and attach to the shower holder.
Protective
Sheath
Shower Holder
Straight Connector
90° Elbow
Plumbers tape
CALHOUN
SHOWER SYSTEM
SKU: 927746

26. Determine the locations of the valve body and
shower head. Connect the inlet pipe to the inlet joint.
Install the 90° female elbow in the hand shower holder
location.
27. Place the locating plate on the shower holder.
Install the plugs and protective sheath.
28. Mark the location of the mounting holes on the
locating plate in the installation location. Use a level to
ensure the holder is aligned properly.
10 1.800.855.2284
90° Female Elbow
Keep in Line
Hot Water
Inlet
Cold Water
Inlet
Locating
Plate
Protective
Sheath
Plug
Pencil
CALHOUN
SHOWER SYSTEM
SKU: 927746