Simrad ITI User manual

Simrad ITI
Trawl instrumentation system
Operator manual

Simrad ITI
Trawl Instrumentation System
Base version
850--043814 / AA000

Operator manual
1
850--043814D
Note
Simrad AS makes every effort to ensure that the information contained within this
document is correct. However, our equipment is continuously being improved and
updated, so we cannot assume liability for any errors which may occur.
Warning
The equipment to which this manual applies must only be used for the purpose for
which it was designed. Improper use or maintenance may cause damage to the
equipment or injury to personnel. The user must be familiar with the contents of the
appropriate manuals before attempting to operate or work on the equipment.
Simrad AS disclaims any responsibility for damage or injury caused by improper
installation, use or maintenance of the equipment.
Copyright
.2002 Simrad AS
The information contained within this document remains the sole property of Simrad
AS. No part of this document may be copied or reproduced in any form or by any
means, and the information contained within is not to be communicated to a third
party, without the prior written consent of Simrad AS.
Simrad AS
Strandpromenaden 50
Boks 111
3191 Horten
Telephone: [phone]
Facsimile: 33 04 29 87
Internet: www.simrad.com
A
L W A Y S A T T H E F O R E F R O N T O F T E C H N O L O G Y

Cover and Contents
I
P2212D
Sections
1 System familiarization
This section defines and describes the main system units, and presents a brief theory
of operation.
2 Operational procedures
This section presents the most common procedures to cover the normal day- to- day
operations.
3 Screen presentation modes
This section describes the various operational modes and the information found on the
display.
4 Command references
This section describes each command and option in detail. The document is intended
for reference purposes only.
5 ITI sensors
This section describes the sensors used with the ITI system. The description includes
charging procedures and technical specifications.
6 On--board maintenance
This section describes the preventive and corrective maintenance actions to be
performed by the ITI operator on board the vessel.
7ITIEthernet
This section describes the Ethernet commands.
8 Technical specifications
This section lists the main technical specifications of the Simrad ITI system.

Simrad ITI Base version
II P2212D
Remarks
References
Further information about the ITI system may be found in the following manual:
·ITI Installation Manual, P2257.
The reader
This operator manual is intended to be used by the system operator. He/she should be
experienced in the operation of positioning systems, or should have attended a Simrad
training course.
Note
This manual includes sections that may be revised individually. In the event of a
revision to any part of this manual, this “Cover and Contents” section will be replaced.

Cover and Contents
III
P2212D
Document revisions
Rev Written by Checked by Approved by
Date Sign Date Sign Date Sign
A . . .
B
C02.04.93 NB 02.04.93 KEG 02.04.93 TAL
D16.01.97 CL 16.01.97 EPB 16.01.97 KEG
E
F
G
H
The original signatures are recorded on the company’s logistic data system.

Simrad ITI Base version
IV P2212D
Simrad References
(The information on this page is intended for Simrad’s internal use)
Documents
Sect Title Loc. File P. n o / R e v
0Cover and contents AA000 850--043814 P2212D
1System familiarization 4AA024 850--130062 P3054/A
2Operational procedures 4A0024 850--130661 P3053/A
3
4
5
6
7
8
Screen presentation modes
Command references
ITI sensors
On--board maintenance
ITI Ethernet
Technical specifications
4A0024
4A0024
4A0024
4A0024
4A0024
4A0024
850--130663
850--130660
850--130665
850--160664
850--160071
850--130666
P3055/A
P3052/A
P3057/A
P3056/A
P3454/A
P3058/A
Revisions
Rev. A First edition
Rev. B Second edition
Rev. C New software version 2.12
Rev. D Manual updated to reflect new software version 3.10. At the same
time Simrad’s new documentation standard has been implemented.
To assist us in making improvements to the product and to this manual, we would
welcome comments and constructive criticism. Please send all such - in writing or by
Email - to:
Simrad AS
Documentation Department
P.O.Box 111
N- 3191 Horten
Norway
or Email:
simrad.docum[email protected]