USES
8
PANEL OPENING
Itispossibletoopenthecoverpanelofthegre-
aseltersbypullingitgentlyasshowning.1.
Thepanelisxedby4magnets,therearealso4
safetycablestobereleasedtocompletelyremo-
vethepanelfromtheproduct(g.2).
FORSLT972-SLT974-SLT979
Itispossibletoopenthepanel,whichcoverthe
greaselters,slightlypullingthepanelonaside,
asshownong.14.
Itisrecommendedtoinstalltheproductatama-
ximumdistanceof2000-2100mmfromtheoor
level.
Beforeproceedingwiththeinstallationoftheap-
pliance, check that all the components are not
damaged, otherwise contact the dealer and do
notproceedwithinstallation.
Useanairoutletpipethathasthemaximumleng-
thofnomorethan5meters.
- Limit the number of bends in the canalization
since each bends reduces the suction efcien-
cy equivalent to 1 linear meter. (for example if
n°290°bendsareusedthelengthoftheducting
shouldnotexceed3meters).
-Avoiddrasticchangesofdirection.
-Useaductwithaconstantdiameterof150mm
overtheentirelength.
-Use a material approved by standards and re-
gulations.
SLT978 EXTERNAL MOTOR
INSTALLATION
Removetheproductfromthepackageandplace
itonasuitablesurface:wesuggestusingasoft
material,suchasaspongeorcloth.
OpenthepanelbyturningitasshowninFig.1,
taketheledlampfromthepackage,insertthe4
steelcablesofthelampintheuppercasing(g.
4),payattentionthesteelcableswiththelabels
mustbeinsertedrespectivelyinthe2holesposi-
tionedneartheelectricalsystem(g.4A).
Fasten the cable and adjust the desired height
ofthelampfromtheoor,actingintheclamping
clampofthecableasshowning.5.
For a good installation, position the lamp at an
heightof1200mmfromthetoppanelofthehood
and 700mm from the cook-top (see g. 6), to
positioniteasily,takethecableoutofthecable
clampataheightof80mm(g.6A).
Make the electrical connection of the lamp, be
carefulnottoconfusethepositive,negativeand
earth polarities indicated by the labels on the
electricalcables(g.4B).
Cut-outDimensions:
915mmx425mm
Markthehoodxingholesshowning.7onthe
solidceiling.
Drill the four holes by using an 8mm diameter
twistdrill.
Insertthewallplugsandthethreadedbarssup-
pliedintheholesmade.
Youcanchoosethesideofthehoodwheretot
theair-outlet,byfollowingthesesteps:
Open the panels, by following the in structions
givenintheOPERATIONMODE
section,andremovethegreaselters(g.3).
Inordertottheairout-letonthehoodupper
side,youneedtoopentheholeinthecentreof
thehoodupper side(g.8)andt theair-out-let
ange,asshowningure9.
Inordertottheairout-letineitherthelongeror
the shorter side of the hood, you need to open
theholeinthelongerortheshorterside(g.10)
andttheair-out-letange,asshowningure11.
Raiseuptheapplianceclosetotheceiling,con-
necttheairoutletducting,connectthemotorca-
bleandpowersupplycable(g.12).
