Skymsen LAR-04 User manual

31190.1-Junho/2010
Instructions Manual
High Performance Industrial Blenders
Models:
LAR - 04
LAR - 04
- ALÉM DESTAS MÁQUINAS, FABRICAMOS UMA LINHA COMPLETA DE EQUIPAMENTOS. CONSULTE SEU REVENDEDOR.
- ESTE PRODUTO CONTA COM ASSISTÊNCIA TÉCNICA, REPRESENTANTES E REVENDEDORES EM TODO TERRITÓRIO NACIONAL.
DEVIDO À CONSTANTE EVOLUÇÃO DOS NOSSOS PRODUTOS, AS INFORMAÇÕES AQUI CONTIDAS PODEM SER MODIFICADAS SEM AVISO PRÉVIO.
PRODUTOS
LINHA DIRETA
SKYMSEN
Ram ais 2 011
201 2
201 3
E-mail: [email protected]
METALÚRGICA SIEMSEN LTDA.
Rua Anita Garibaldi, nº 262 – Bairro: Sno Luiz – CEP: 88351-410
Brusque – Santa Catarina – Brasil
Fone: [phone] – Fax: [phone]
www.siemsen.com.br - [email protected]
METALÚRGICA SIEMSEN LTDA.

Table - 02
Problems Causes Solutions
* Lack of power.
* Problem in the electric circuit
of the machine.
* Check if machine is
plugged in and if there is
power in the power supply
source.
* The machine does not turn
on.
* Cup is leaking.
* The machine turns on but
the motor turns slowly.
* Damaged seal.
* Defected motor capacitor.
* Call technical assistence.
5.2 Electrical Diagram
* Power cord damaged. * Faulty transportation.
5 Analysis and Problems Solving
5.1 Problem, causes and solutions
The High Performance Industrial Blenders were designed to operate with the
need of minimum maintenance but the natural wearing caused by longer use of the
equipment may occasionally cause some malfunctions.
If such problem occurs with your Blender refer to Table 02 in which the most
common situations are listed with recommended solutions.
* Call technical assistence.
* Call technical assistence.
* Call technical assistence.
.
5
0
4
1
1
3
ON/OFF SWITCH/ PULSE
THERMIC
SWITCH
09

0108
SUMMARY
1.2 Main Components
1.3 Technical Characteristics
1.4 Labels
1. Introduction
2
1.1 Safety
2
2
3
3
2. Installation and Pre Operation
2.1 Installation
2.2 Pre Operation
4
4
4
3. Operation
3.1 Starting
3.3 Cleaning
3.2 Operating Procedures
5
5
5
5
5. Analysis and Problem Solving
5.1 Ploblems, Cause and Solutions
9
5.2 Electric Diagram
9
9
4. General Safety Practices
4.1 Basic Operation Procedures
4.4 Operation
4.2 Safety Producedures and Notes Before Switching the Machine On
4.5 After Finishing the Work
4.3 Routine Inspection
4.6 Maintenance
4.7 Advices
6
6
7
8
8
8
8
9
4.4 Operation
4.4.1 Advice
Be sure your hair is not loose in order to avoid getting caught by turning parts
which could lead to a serious accident. Tie your hair well up and/or cover your head
with a scarf.
The operation performed by not trained or skilled personnel shall be
forbidden.
Never touch turning parts with your hands or in any other way.
NEVER operate machine without all original safety devices under perfect
conditions.
4.5 After Finishing The Work
4.5.1 Precautions
Always TURN THE MACHINE OFF by removing the plug from the socket
before cleaning the machine.
Never clean the machine unless it has come to a COMPLETE STOP.
Put all components back to their functional positions before turning it ON
again. DO NOT place your fingers in between belts and pulleys nor chains
and gears.
4.6 Maintenance
4.6.1 Danger
Any maintenance with the machine in working situation is dangerous. TURN
IT OFF BY PULLING THE PLUG OFF THE SOCKET DURING MAINTENANCE.
IMPORTANT
A l w a y s u n p l u g t h e m a c h i n e w h e n e m e r g e n c y c a s e s a r i s e .
4.7 Advice
Electrical or mechanical maintenance must be done by qualified personal for
such operation.
Person in charge has to be sure that the machine is under TOTAL SAFETY

02
1. Introduction
1.1 Safety
Picture - 01
01- Lid
02- Cup
03- Cup Flange
04- Motor Support Flange
05- Motor Housing
06- Base
07- Thermic Switch
08- ON/OFF Switch
07
The High Performance Industrial Blenders are machines simple to use and to
clean. However for your safety read the following instructions in order to avoid
accidents:
1.1.1 Always unplug the machine when cleaning, servicing or when any other
operation is needed.
1.1.2 Never use tools that do not belong to the machine during operation.
1.1.3 Before using the machine check if Cup Nº02 (Pic.01) is properly fitted in its
position.
1.1.4 Never throw water directly to the machine.
1.1.5 Do not operate the machine wearing wet clothes or wet shoes.
1.1.6 Before operating the machine be sure it is grounded properly.
IMPORTANT
This equipment shall not be used by persons (including children) having reduced
mental or physical capabilities, or having faulty experience or knowledge, unless
they have been previously supervised or instructed by a person responsible for the
equipment safety, about how to use it.
IMPORTANT
If the cord is not in good conditions to be used, it has to be changed by the
manufacturer or an Authorized Technical Assistant.
1.2 Main Components
All components are made with carefully selected materials, in accordance with
Siemsen experience and standard testing procedures.
The equipment has additional protection against failure . The motor and the
operator are protected against any adverse situation .
The protection is a thermal protector . If the equipment stops all of a sudden wait
some minutes and press the thermal protection button .
01
02
03
05
07
08
04
06
Removed or is no longer legible, contact your nearest dealer for replacement.
4.2 Safety Procedures and Notes Before Switching Machine
ON
IMPORTANT
Carefully read ALL INSTRUCTIONS of this manual before turning the machine ON.
Be sure to be familiar with the instructions and that you have well understood all
information contained in this manual. If you have any question contact your
supervisor or your nearest Dealer.
4.2.1 Danger
An electric cable or electric wire with damaged jacket or bad insulation could
cause electrical shocks as well as electrical leak. Before use, check conditions of all
wires and cables.
4.2.2 Advices
Be sure ALL INSTRUCTIONS in this manual have been thoroughly understood.
Every function and operational procedure have to be very clear to the operator. Contact
your nearest Dealer for further questions.
Any manual command (switch, button or lever) shall be given only after being
sure it is the correct one.
4.2.3 Precautions
The electric cable has to be compatible with the power required by the
machine. Cables touching the floor or close to the machine need to be protected
against short circuits.
4.3 Routine Inspection
4.3.1 Advice
When checking the tension of the belts or chains, DO NOT introduce your
fingers between the belts and the pulleys and nor between the chain and the gears.
4.3.2 Precautions
Check if motors and sliding or turning parts of the machine produce abnormal
noises.
Check the tension of the belts and chains and replace the set when belt or
chain show signs of being worn out.
When checking tensions of belts or chain DO NOT introduce your fingers
between belts and pulleys, nor between the chains and gears.
Check protections and safety devices to make sure they are working properly.

03
1.3 Características Técnicas
Table - 01
Characteristics
Unit.
LAR-04
220
50
0,5
0,38
620
260
210
8,8
Voltage
Frequency
Power Rating
Consuption
Heigth
Width
Depth
Net Weight
Shipping Weight
[V]
[Hz]
[CV]
[kW/h]
[mm]
[mm]
[mm]
[kg]
[kg]
[ rpm]Rotation
9,6
3500
06
1.4 Labels
00047.7 LOGOSKYMSEN
32832.4 INSTRUCTION MANUAL LABEL
31140.5 LAND SYMBOL LABEL
METALÚRGICA SIEMSEN LTDA.
33282.4
5
.
0
4
1
1
3
4. General Safety Practices
The following safety instructions are addressed to both the operator of the
machine as well as the person in charge of maintenance. The machine has to be
delivered to the operator in perfect conditions of use by the Distributor to the user. The
user shall operate the machine only after being well acquainted with the safety
procedures described in the present manual. READ THIS MANUAL WITH
ATTENTION.
4.1 Basic Operation Practices
4.1.1 Dangerous parts
Some parts of the electric devices are connected to high voltage points.
These parts when touched may cause severe electrical shocks or even be FATAL.
Never touch commands such as buttons, switches and knobs with wet hands,
wet clothes and/or shoes. By not following these instructions operator could be
exposed to severe electrical shocks or even to a FATAL situation.
4.1.2 Warnings
The operator has to be well familiar with the position of ON/OFF Switch to
make sure the Switch is easy to be reached when necessary. Before any kind of
maintenance, physically remove plug from the socket.
Provide space for a comfortable operation thus avoiding accidents.
Water or oil spilled on the floor will turn it slippery and dangerous. Make sure the floor
is clean and dry.
Before giving any manual command (switch, buttons, turn keys or lever) be
sure the command is the correct one. Check this manual for further details if
necessary.
Never use a manual command (switch, buttons, lever) unadvisedly.
If any work is to be made by two or more persons, coordination signs will
have to be given for each operation step. Every step of the operation shall be taken
only if the sign has been made and responded.
IMPORTANT
If any item from the GENERAL SAFETY NOTIONS section is not applicable to
your product, please disregard it.
4.1.3 Advices
In case of power shortage, immediately turn the machine OFF.
Use recommended or equivalent lubricants, oils or greases.
Avoid mechanical shocks as they may cause failures or malfunction.
Avoid penetration of water, dirt or dust into mechanical or electrical components of
the machine.
DO NOT MODIFY original characteristics of the machine.
DO NOT REMOVE, TEAR OFF or MACULATE ANY SAFETY or I
DENTIFICATION LABELS stuck on the machine. If any label has been

04 05
2.2 Pré-Operação
Picture - 02
Picture - 03
2. Instalação e Pré-Operação
850 mm
2. Installation and Pre Operation
2.1 Installation
The Blender is to be installed onto a leveled surface approximately 850mm
high.
The High Performance Industrial Blenders were developed to be used in
220V.
The cord has 3 (three) round pines, being one of them the land pin. It is
mandatory the three pins to be duly connected before to start the machine.
IMPORTANT
When installing the Cup Nº02 (Pic.01) in the machine be sure it is perfectly fitted.
The Cup can be fitted in the machine in any position; which guarantees a perfect
operation.
First of all check if the Blender is firm in its position. It is recommended to
work with the machine in a flat surface with approximately 850mm of height.
Before using the machine all parts that get in contact with food must be
washed with running water and neutral soap. To clean your Blender read item 3.3
Cleaning on this Manual (pag.4).
5
0
.
4
1
1
3
3.1 Starting
3. Operation
IMPORTANT
Before removing or installing the Cup Nº02 (Pic.01) be sure the motor has completely
stopped in order to avoid coupling premature wear out.
3.3 Cleaning
The Blender is activated by turning the On/Off Switch Nº08 (Pic.01) located
in the Motor Housing Nº05 (Pic.01) to ON position.
3.2 Operating Procedures
The High Performance Industrial Blender work at high speed (approximately
3.500 rpm). To feed it proceed as follows:
1 - Remove the Lid Nº01 (Pic.01).
2 - Put product inside the Cup Nº02 (Pic.01) with the machine switched OFF.
3 - Place the Lid Nº01 (Pic.01) back on top of the Cup and switch the
machine ON.
IMPORTANT
Never do cleaning with machine plugged in. Always unplug machine before
cleaning. Before removing the Cup be sure the motor has completely stopped.
When washing inside the Cup be careful with the blade.
The new SKYMSEN Blenders models were developed for easy cleaning.
Wash the removable parts with running water and neutral soap and wipe up the
others with a damp cloth.
IMPORTANT
The processing time depends on the kind of product. It is not recommended to
blend products without the addition of any liquid, otherwise it will overheat and
damage the Cup seal.
IMPORTANT
NEVER SWITCH THE MACHINE ON WITHOUT LOAD IN IT BECAUSE IT WILL
CAUSE IRREPARABLE DAMAGES.
Follow the below instructions for washing removable parts:
3.3.1 Unplug the machine.
3.3.2 Remove the Lid Nº01 first then the Cup Nº02 (Pic.01).
3.3.3 Wash all removable parts with running water and neutral soap.
3.3.4 To reinstall them, follow the above order inversely.
IMPORTANT
When washing inside the Cup be careful with the blade as it has sharp edges.