Skyrc 4P3 User manual

INSTRODUCTION
INSTRUCTIONMANUAL
CHARGING STATION 4P3 SK-100118
The Charging Station 4P3 is a four channels charger designed and built exclusively for Phantom3
Smart Battery. This charger is capable of charging, storage and deep cycling four DJI smart batteries
simultaneously. Two smart devices can be charged via USB port and two remote controller can be
charged at same time.
This unit is simple to use, but the operation of a sophisticated automatic charger such as Charging
Station 4P3 does require some knowledge on the part of the user. These operating instructions are
designed to ensure that you quickly become familiar with its functions. It is therefore important that
you read right through the Operating Instructions, Warning and Safety Notes before you attempt to
use your new charger for the first time. We hope you have many years of pleasure and success with
your new battery charger.
Battery
slot
Carring
Handle
Cooling Fan
Power Switch
AC Socket
100-240V
Battery Level
Percentage
Battery Voltage
Storage Button
Cycle Button
Output Power
Indicator
Charging Port
for Remote Controller
USB Power
for Smart Device
Cooling Fan
LED Display
CHARGING YOUR BATTERIES
Connect the Power Cord to the AC socket(100-240V).
Turn ON the Power Switch. The LED display show “CHA” and the
charger is in CHARGE MODE.
Insert the battery into the battery slot. The 4P3 will communicate
with the battery and send the battery into CHARGE MODE
automatically.(If the battery level is above 95%, turn on the battery
before charging.)
The battery’s green LED will be blinking. and the LED display will
show charging percentage of battery. When the battery is fully
charged. The battery’s green LED’s will turn OFF and the charger
station will beep 5 times. Remove the battery and turn off
Charging Station 4P3.
1.
2.
3.
1.
STORAGE MODE
When the battery is idle for more than ten days. It is better to discharge
the battery to 65% of total power in order to prevent swelling. If the
battery level is below 65%(15.6V), you need recharge it to 65%.
Push storage button, the LED will show .
Turn ON the battery before you put it in STORAGE MODE.
Press the Power Button once, then press again and hold for 2 seconds
to turn on. The Power LED will turn red and the battery level Indicators
will display the current battery level.
Insert the battery into the battery slot. The battery’s green LED will be
blinking. and the LED of charger will display voltage of the battery.
If the battery level is more than 65%, Charging Station 4P3 will
discharge the battery to 65%. If the battery level is below 65%, this unit
will charge the battery to 65% for storage automatically.
When the battery level is reached 65%, the LED will display and
repeatly and beeps 5 times. Remove the battery and turn off Charging
Station 4P3.
2.
3.
4.
5.
1. Charging Station 4P3
2. Power Cord
3. Remote Controller Charging Cable x 2
CONTENTS
Press the Power Button once
Press Again and Hold
for 2 Seconds to Turn On
Insert the Battery Into the Battery Slot
Push Storage Button
1 2
SPECIFICATIONS
Input Voltage:
Charge Power:
Charge Current:
USB Output:
DC Output:
AC 100-240V
100W x 4
6.0A
5V/2.1A x2
19V/2A x2
Working Mode:
Size:
Weight:
Charge Mode
Storage Mode
Cycle Mode
255x142x180mm
3.22kg

Never leave the charger unattended when it is connected to its power socket. If any malfunction is found,
TERMINATE THE PROCESS AT ONCE.
Keep the charger well away from dust, damp, rain, heat, direct sunshine and vibration. Never drop it.
Never charge batteries on wood, cloth, carpet or on any other flammable material.
During charging, the charger must be placed in a well ventilated area.
This charger is designed and built exclusively for Phantom3 Smart Battery. The allowable AC input voltage is
100~240V AC.
Manufacturedby
SKYRCTECHNOLOGYCO.,LTD.
www.skyrc.com
RoHS 7504-0750-02
This appliance can be used by children aged from 14 years and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children without supervision.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons
in order to avoid a hazard.
This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent
possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the
sustain able reuse of material resources. To return your used device, please use the return and collection systems or
contact the retailer where the product was purchased. They can take this product for environmental safe recycling.
CYCLE MODE
Note: For extended life of your batteries, it is recommended that you DEEP CYCLE your batteries
following 10 flight cycles.
Push cycle button, the LED will show .
Turning On the battery:
Press the Power Button once, then press again and hold for 2 seconds to turn it on . The Power LED will
turn red and the battery level Indicators will display the current battery level.
Insert the battery into the battery slot. The 4P3 will discharge it to 13.2V.
Once discharge to 13.2V, the 4P3 will automatically send the battery into CHARGE MODE.
When the battery is fully charged. The battery’s green LED’s will turn OFF and the charger station will beep
5 times. Remove the battery and turn off Charging Station 4P3.
1.
2.
3.
4.
5.
CHARGING YOUR REMOTE CONTROLLER
Turn ON the Charging Station 4P3.
Connect your remote controller to the DC charging port using
the cable supplied.
When the 4 LED’s on the remote controller are WHITE, it is
fully charged.
Remove the cable from the Charging Station 4P3.
Turn OFF the Charging Station 4P3.
5.
4.
1.
2.
3.
3 4
This symbol means that you must dispose of electrical from the general household waste when it reaches the end of
its useful life. Take your charger to your local waste collection point or recycling centre. This applies to all countries
of the European Union, and to other European countries with a separate waste collection system.
The Charging Station 4P3 satisfy all relevant and mandatory CE directives and FCC Part 15 Subpart B: 2016.
EN55014-1:2006+
A1:2009+A2:2011
Electromagnetic compatibility - Requirements for household
appliances, electric tools and similar apparatus - Part 1: Emission
EN55014-2: 1997+
A1:2001+A2:2008
Electromagnetic compatibility - Requirements for household
appliances, electric tools and similar apparatus - Part 2:
Immunity - Product family standard
EN 61000-3-2:2014
Electromagnetic compatibility (EMC) - Part 3-2: Limits - Limits for
harmonic current emissions (equipment input current <= 16 A per
phase)
EN 61000-3-3:2013
Electromagnetic compatibility (EMC) - Part 3-3: Limits - Limitation
of voltage changes, voltage fluctuations and flicker in public low-
voltage supply systems, for equipment with rated current <= 16 A
per phase and not subject to conditional connection
EN 60335-1: 2012
+A11: 2014
Household and similar electrical appliances - Safety - Part 1:
General requirements
EN 60335-2-29:
2004+A2: 2010
Household and similar electrical appliances - Safety - Part 2:
Particular requirements for battery chargers
EN 62233: 2008 Measurement methods for electromagnetic fields of household
appliances and similar apparatus with regard to human exposure
For EC directives:
The product has been tested to meet the following technical standards:
CHARGING YOUR iOS DEVICE OR ANDROID DEVICE
Turn ON the Charging Station 4P3.
Connect your smart device to the USB port using the cable supplied by smart device's manufacturer.
When your smart device shows 100%, it is fully charged.
Remove the cable from the Charging Station 4P3.
Turn OFF the Charging Station 4P3.
1.
2.
3.
4.
5.
OPTIONAL PART
CableAdaptor for PHANTOM 4 Battery
SK-600023-04