Slinex RD-30 User manual

{ Design. Uniqueness. Innovations}
RD-30 doorbell
wireless kit
SERIES
ACCESSORIES
Thank you for
choosing our equipment
User manual

{ Design. Uniqueness. Innovations }
1Rev. 1.0 2
SERIES
ACCESSORIES
Attention!
As a result of continuous upgrades and functionality improvements, technical
characteristics of the device can be changed without any preliminary declaration.
This manual can contain some inaccuracy or misprint. The owner reserves the right to
make corrections to the information described in the user manual and device package.
The last revision of this manual is available on www.slinex.com
Safety instructions
Read and keep that manual.
The device installation process should be carried out by the qulied specialists.
Use the device from –10 ˚C to +55 ˚C, always keep it within that temperature range.
Installation surface should be free from vibration and impact inuence.
Keep this device far from open sources of heat, such as radiators, heaters, and ovens.
The device can be installed near other electronic equipment in case if the temperature of the environment
does not exceed previously mentioned range.
The device should be protected from the direct inuence of the natural phenomena, such as direct sunlight,
rain or snow.
Don’t use aggressive or abradant detergent for the device surface cleaning.
Use soft wet cloth or tissue to remove strong dirt.
Don’t overpower outlets. It can cause re or electric shock.
Nature protection
Don’t throw away the device with other industrial or nutritive trash if you see that
symbol. Some regions have separation and recycling systems for the electronic
equipment. Connect with local authorities to receive information about recycling of
electronic equipment for your region.
Rights and limitation of liability
All rights reserved. Any part of that document can not be published in any form, translated into other
languages or reproduced in any way including electronic or mechanical.
Document recording and copying is strictly denied without owner permission.
!
Table of contents
1. Package ......................................................................................................................................................................................... 3
2. Specication ................................................................................................................................................................................ 3
2.1 Outdoor panel specication ................................................................................................................................3
2.2 Handset specication ............................................................................................................................................. 4
3. Description................................................................................................................................................................................... 5
4. Battery installation .................................................................................................................................................................... 6
5. Charging device operation.....................................................................................................................................................7
6. Schematic diagrams ................................................................................................................................................................. 7
7. Installation.................................................................................................................................................................................... 8
8. Handset turning on/o............................................................................................................................................................ 9
9. Operation....................................................................................................................................................................................10
9.1 Incoming call ...........................................................................................................................................................10
9.2 Outdoor panel monitoring.................................................................................................................................11
10. Handset settings....................................................................................................................................................................11
10.1 Settings navigation.............................................................................................................................................11
10.2 Settings menu structure ...................................................................................................................................12
11. Taking snapshots...................................................................................................................................................................14
12. Snapshots playback..............................................................................................................................................................14
13. Engineering mode ................................................................................................................................................................15
13.1 Outdoor panel registration..............................................................................................................................15
13.2 Energy saving mode...........................................................................................................................................15
14. Connection quality...............................................................................................................................................................16
15. Limited Warranty...................................................................................................................................................................17

3 4
Frequency
Camera sensor type
Sensor resolution
Codec
View angle (diagonal)
Night backlight
Power adapter
Battery
Working mode power consumption
Lock relay current
Mounting type
Dimensions
Working temperature
2.4000 - 2.4835 GHz
СMOS
640х480 pixels
H.264
120˚
white LED’s − 6 pcs.
12 V, 500 mA (optional)
LR14 C (1.5 V) - 2 pcs.
6 W
1А
Surface mount
105×167×50 mm (4.1×6.6×2.0“)
–20 ... +55 ˚C (–4...131 ˚F)
Screen
Screen resolution
Transmitting power
Outdoor panels quantity supported
Charging power adapter
Battery
Handset dimensions
Charging device dimensions
Working temperature
2.4” color TFT
320х240 pixels
19 dBm
2 pcs.
12 V, 500 mA
BL-5C, 3.7 V, 1100 mAh (lithium battery)
53×188×26 mm (2.1×7.4×1.0“)
80×95×104 mm (3.1×3.7×4.1“)
–10 ... +40 ˚C (14 ... +104 ˚F)
2.2 Handset specication
1. Package
Outdoor panel − 1 pc.
Outdoor panel mounting bracket − 1 pc.
Outdoor panel caps and screws − 1 kit (2 caps)
Outdoor panel power supply − 1 pc.
Handset − 1 pc.
Handset charging device − 1 pc.
Power supply for charging device − 1 pc.
Handset battery − 1 pc.
Screws and anchors − 1 kit
User manual − 1 pc.
2. Specication
2.1 Outdoor panel specication
{ Design. Uniqueness. Innovations }
SERIES
ACCESSORIES
167 mm (6.6“)
188 mm (7.4“)
105 mm (4.1“)
53 mm (2.1“)

5 6
3. Description
{ Design. Uniqueness. Innovations }
SERIES
ACCESSORIES
Light sensor
Microphone
Camera
Call button
Speaker
Speaker
Battery
compartment
cover
Night backlight
Display
Navigation button
Right program button
«View» / «Take snapshot» button
«Power» / «Hang on» / «Exit» button
Left program button
«Answer» button
«Open lock» button / charging
indicator
Microphone
Charging
device
contacts
4. Battery installation
Handset battery included into doorbell kit. Slide o battery compartment cover, remove protection lm on
the battery contacts and install it into battery compartment (pay attention on battery polarity while
installation). Attach battery compartment power back to the handset and turn on the power by holding
«Power» button.
Outdoor panel can be powered from the battery or from the external power supply 12V, 500mA (optional)*.
In case of battery power, install two type C 1.5V batteries into outdoor panel battery compartment (pay
attention on batteries polarity while installation) . Attach battery compartment cover and x it by the screw
from the kit.
In case of using external 12V, 500mA power supply, connect two wires from the power supply to the
outdoor panel connector taking into consideration wires polarity.
Battery
Protection lm
Battery compartment
Battery compartment cover
2
1
Battery
Battery compartment cover
Screw
Note:
* Don’t use batteries and external power supply simultaneously to power outdoor panel. It can cause
damage to the system. In case of outdoor panel battery power, manual image monitoring will be disabled
in terms of energy saving. To enable manual monitoring you should disable energy saving mode.
Instructions on how to do that you can nd on page 15.

7 8
{ Design. Uniqueness. Innovations }
SERIES
ACCESSORIES
5. Charging device operation
Power supply socket situated on the bottom side of the charging device. Connect power supply from the kit
to the charging device then connect it to the socket and put the handset to the charging device cup.
Fully charge the battery before the rst use.
6. Schematic diagrams
Diagram 1. Outdoor panel and electromechanical lock connection.
7. Installation
1) After all wires have been connected, t them into the groove, install the cap and x it by four screws
from the kit.
(+)
(–)
Electromechanical
lock Lock power
supply
Outdoor panel
Power supply
12V, 500mА
Reserve 12V
battery
+9..12V
Ground
Battery
COM.
N.O.
N.C.
Exit button
+
–
Diagram 2. Outdoor panel and electromagnetic lock connection.
(+)
(–)
Exit
button
+
–
Electromagnetic
lock Lock power
supply
Outdoor panel
Power supply
12V, 500mА
Reserve 12V
battery
+9..12V
Ground
Battery
COM.
N.O.
N.C.
Exit button

9 10
{ Design. Uniqueness. Innovations }
SERIES
ACCESSORIES
2) Take the surface mount bracket from the kit and place it 150-160 cm (5 ft.) up from the oor line.
3) Mark and drill two holes in the wall 60mm (2,36”) from each other horizontally.
4) Take two wall anchors from the kit and hammer them into the drilled holes.
5) Fix surface mount bracket on the wall by two screws from the kit.
6) Connect all communication wires and x the door panel inside the surface mount bracket by the screw
from the down side.
8. Handset turning on/o
Press and hold button to turn on the handset.
After turning on the handset next image will appear on the screen:
Press and hold button any time in active mode to turn o the handset.
When battery power is low, the icon will appear on the screen and you will hear warning sound.
After that handset will be turned o and it needs to be charged.
9. Operation
9.1 Incoming call
Standby mode
Standby mode
Visitor presses
call button on the
outdoor panel
Melody is ringing on the
handset and outdoor panel,
image from the outdoor panel
appears on the handset screen
Press «Answer» button
to start conversation
with the visitor
Press «Hang up» button
to stop conversation or
incoming call
Melody stops ringing and
conversation starts,
talking time is 50 seconds
Press «Unlock» button to
open lock, connected to
the outdoor panel
Notes:
1) Monitor will be automatically switched into standby mode if the user doesn’t answer incoming call
during 15 seconds (default value);
2) Image and sound from the outdoor panel will be disabled after the moment user presses button.
15:36
Menu Mon

Select Back
Volume
Ring Time (s)
Unlock Time (s)
11 12
{ Design. Uniqueness. Innovations }
SERIES
ACCESSORIES
9.2 Outdoor panel monitoring
Press any key to activate handset screen.
Then press «Mon» key which matches right
program key on the handset main screen.
10. Handset settings
10.1 Settings navigation
Press any key to activate handset screen. Left and right bottom keys on the screen matches left and right
program buttons on the handset keyboard (see schematic diagram on page 5).
Press left program key on handset keyboard to enter main settings menu.
Use and buttons to move through the menu.
Use button to select current sub menu.
Use button to exit current screen.
Use and buttons to change current parameter value.
10.2 Settings menu structure
Handset menu has the following structure:
Select Back
Brightness
– +
Select
Menu
Back
2
15
Main menu
1st page
Main menu
2nd page
1# 001/005
2018-04-18
11:44
Standby mode
Standby mode
Press «Unlock» button to
open lock connected to
the outdoor panel
Press «Answer» button
to start conversation
with the visitor
Press «Hang up» button
to stop monitoring or
conversation
Monitor will display
the image from the
outdoor panel
(monitoring time – 45 seconds)
Mon
Select Back
Talking Volume
Ringing Volume
Ringing Time
15s
Select Back
Clock
Date
Select Back
Key Tone
ON
OFF
Select Back
Auto Snap
ON
OFF
Select Back
Ring Tone
Ring Tone 1#
Ring Tone 2#
Ring Tone 3#
16 : 04
2018 - 04 - 16

13 14
{ Design. Uniqueness. Innovations }
SERIES
ACCESSORIES
Handset rmware version
Outdoor panel registration number
Outdoor panel rmware version
0
С: 1.2 20170223
R: 1.2 20170110
----------1#--------
С: 1.2 20170328
R: 1.1 20161011
M: 1.1 20161125
#
12. Snapshots playback
Enter «Snap Show» menu on the 2nd page of settings menu. На экране отобразится меню просмотра
фотографий:
11. Taking snapshots
Enter «Snap Set» menu on the 2nd page of settings menu. If «Auto snap»
function is on, then every time somebody calls the outdoor pnel, handset
makes automatic snapshot. Also snapshot can be made manually by
pressing right program key while manual image monitoring or
talking with the visitor.
Use and navigation keys to move through the snapshots list.
Press left program key to delete current snapshot then press left program key again to confirm
operation or press right program key to cancel.
Press key to delete all snapshots then press left program key to confirm operation or press
right program key to cancel.
Press right program key to exit from snapshots playback mode.
1# 001/005
2018-04-18
11:44
1# 001/005
2018-04-18
11:44
1#
11:44
1# 001/005
2018-04-18
11:44
Main menu
3rd page Main menu
4th page

15 16
{ Design. Uniqueness. Innovations }
SERIES
ACCESSORIES
13. Engineering mode
13.1 Outdoor panel registration
Two outdoor panels can be connected to one handset. Every outdoor
panel should be registered on the handset. Registration steps are as
follows:
1. Using screwdriver press and hold «register» button on the back of
outdoor panel during 3 seconds until you will hear sound signal and
call button backlight starts blinking.
2. Enter «Register» menu on the 3rd page of handset settings then
choose channel number which outdoor panel will be connected to,
using and buttons. Then press left program key
to start rigistration proccess. You will hear sound signal and green sign
near chanel number will appear. It means that outdoor panel was
successfully registered on the handset.
If you want to delete registered outdoor panel from the handset
memory, choose chanel number in «Register» menu and press left
program key then press left program key again to confirm
operation or press right program key to cancel. .
13.2 Energy saving mode
While using batteries to power up outdoor panel, energy sving mode is enabled by default. It means that
user can’t monitor image from the outdoor panel in order to save the battery power. In that mode user can
monitor the image from outdoor panel only during incoming call.
In order to disable energy saving mode and enable manual monitoring enter into register mode like it is
described in paragraph 13.1, step 1. Then again press and hold «register» button on the back of outdoor
panel during 3 seconds until you will hear triple sound signal. It means that energy saving mode has been
disabled.
If you want to enable energy saving mode again, please follow the same steps as for disabling that mode
described above.
14. Connection quality .
Since working frequency of that product is 2.4GHz, wireless signal has poor penetration through dierent
obstacles. In order to ensure smooth communication please note the following:
1) Do not install outdoor panel on metallic doors or details that contains metall in their structure. Try
to reduce obstacles quantity between outdoor panel and indoor handset. Every obstacle on the
way absorbs signal intensity. On the picture below you can nd average signal penetration value
through the walls made of dierent materials:
Try to reduce walls quantity on the way from outdoor panel to the indoor handset;
2) Do not install outdoor panel or indoor handset near devices of the same frequency, such as router,
bluetooth or micro wave oven in order to avoid causing the interference and shortening of
communication range.
#
W o od ,
P la ster
B rick,
C o m po s i te M ater
ial
Rei n fo rce d
C o nc r et e
M eta l,
M etal N e
t
Wooden
wall
Brick
wall
Reinforced
concrete
wall
Metallic
wall or net

17 18
{ Design. Uniqueness. Innovations }
SERIES
ACCESSORIES
15. Limited warranty
Manufacturer guarantees product normal functioning during the warranty period if the user keeps all safety
instructions described in that manual.
Warranty period is 12 months from the moment of the product purchasing (warranty period could be
extended up to 24 months or more, depending on the local regulations).
Warranty period allows user to make guarantee repair in cases when normal functioning of the product was
violated by the fault of manufacturer and the user haven’t oend transporting, installation and working
conditions.
This limited warranty does not cover any damage to the product that results from improper installation,
accident, abuse, misuse, natural disaster, insucient or excessive electrical supply, abnormal mechanical or
environmental conditions, or any unauthorized disassembly, repair or modication.
Warranty void in such cases:
• the product was damaged by the fault of the customer;
• the product wasn’t properly installed according reccomendations from the manual;
• the sticker on the backside of the product was broken;
• the product was not used for its intended function.
This limited warranty covers only repair, replacement, refund or credit for defective products, as provided
above. Manufacturer is not liable for, and does not cover under warranty, any damages or losses of any kind
whatsoever resulting from loss of, damage to, or corruption of, content or data or any costs associated with
determining the source of system problems or removing, servicing or installing products. This warranty
excludes third party software, connected equipment or stored data. Manufacturer is therefore not liable for
any losses or damage attributable to third party software, connected equipment or stored data.
In the event a product has been discontinued, manufacturer shall either repair the product, oer to replace
it with a comparable product or provide a refund at the lesser of the purchase price or the product’s current
value.
Repaired or replacement products will continue to be covered by this limited warranty for the remainder of
the original warranty term.