SMART-AVI SWP-T10 User manual

USER MANUAL
(rev 1.0)
Wall Plate Extender
1080p HDBaseT
SWP-T10
Extends VGA, stereo audio, HDMI, IR and RS232
signals with CAT5e/6 up to 70 meters.

WHAT’S IN THE BOX
PART NO. QTY DESCRIPTION
SWP-T10 1 HDBaseT Wall Plate Transmitter
PS12V1.25A 1 Power Supply
1 SWP-T10 Quick Start Guide
CONNECTING THE HDX-WPRO

1.InstalltheSWP‐T10transmitterandplacetheSmartAVIHDXRXreceiver
unitincloseproximitytotheoutputdevice.
2.ConnectaCat5e/6cablebetweentheTXandRXunits(upto70m).
3.ConnectasignalsourcetotheSWP‐T10viaHDMI,VGA,StereoAudio,
RS232orIRconnectors.
4.ConnecttheHDXRXunittothedesiredoutputdevice.
5.Connecta12VpowersupplytoeithertheSWP‐T10ortheHDXRXunit.
TheotherdevicewillbepoweredviaPOE(PoweroverEthernet).
6.UsetheTXfrontpanelSELECTSOURCEbuttontoswitchbetweensource
signals.Usingautomaticselectionwillselectthelastsourceconnected.

Optional:
1. ConnectanRS232cablebetweenSWP‐T10andapersonalcomputerand
aRS232cablefromtheHDXRXunittoanyRS232devicetoremotely
communicatewithorcontrolyourRS232device.
2. ToextendIRremotecontrolfromtheSWP‐T10totheHDXRXunit,con‐
nectanIRreceivertotheSWP‐T10andanIREmittertotheHDXRXfor
infraredremotecontrolupto20m
2 © 2016 SmartAVI, Inc.
SWP-T10

SWP-T10 FRONT
SWP-T10 BACK
SWP-T10 3
© 2016 SmartAVI, Inc.

TECHNICAL SPECIFICATIONS
PORTS
Input ports 1 x HDMI, Type A 19-pin, female; 1 x VGA HD-15, female;
1 x AUDIO IN(Stereo);1 x IR IN; 1 x RS-232 3p captive
screw connector; 1 x 2p captive screw connector
Output ports 1 x IR OUT; 1 x RJ45 (HDBaseT); 1x RS-232 3p captive
screw connector;
VIDEO
Max Data Rate 6.75Gbps
Maximum Pixel
Clock
225MHz
Resolutions Up to 1920x1200 or 1080P@60Hz
Compliance with
HDMI standard
Supports HDMI 1.4 and HDCP1.2
AUDIO
Frequency
Response
20Hz ~ 20KHz
Stereo Channel
Separation
>75dB@20Hz ~ 20KHz
Bandwidth 20Hz ~ 25KHz
OTHER
Power Input 12V DC or 24V DC, 1.25A
Power
Consumption
undetermined
Dimensions(W x D
x H)
4.6” x 4.6” x 1.45”
Weight 0.75lbs
Operating
Temperature
0° to +40°C (32° to 104°F)
Storage
Temperature
-20˚C ~ 60˚C / -4 ˚F ~ 140 ˚F
Humidity 10% ~ 90%
ESD Protection Human body model:
±8kV (air-gap discharge)
±4kV (contact discharge)
4 © 2016 SmartAVI, Inc.
SWP-T10

METHODS TO CONTROL SWP-T10
Front Panel Button
The Select/Auto button selects an input source. If you press and hold the
button, the SWP-T10 will enter the automatic switching mode and the Auto-
Switch LED lights up. If you press and hold the button again, the SWP-T10
will exit the automatic switching mode.
RS-232 External Protocol (PC User)
Supports bi-directional RS-232 pass-through control.
This protocol is for communication between PC user and board. The fol-
lowing settings should be used: 9600 baud rate, 8 data
bits, no parity bits, 1 stop bit, and no flow control.
Table 1: Command Protocol
Switch to HDMI Changes the source to HDMI //HD<CR><LF>
Switch to VGA Changes the source to VGA //VG<CR><LF>
Auto ON Enable auto-switching by detecting hot plug. //AE<CR><LF>
Auto OFF Disable auto-switching by detecting hot plug. //AD<CR><LF>
RES 1 Select Change the resolution to 1920 x 1200. //R1<CR><LF>
RES 2 Select Change the resolution to 1920 x 1080. //R2<CR><LF>
RES 3 Select Change the resolution to 1360 x 768. //R3<CR><LF>
RES 4 Select Change the resolution to 1280 x 720. //R4<CR><LF>
RES 5 Select Change the resolution to 1024 x 768. //R5<CR><LF>
SW Update Software update for MSTAR chip. //SU<CR><LF>
Reset to Default Reset to factory defaults //RD<CR><LF>
Table 2: Query Protocol
Version Checks current version of MSTAR software. //V?<CR><LF>
Version Vx.x.x
CHK RES Checks the current resolution. //R?<CR><LF>
Resolution: xx
CHK SRC Checks the current source. //S?<CR><LF>
Input: xx
SWP-T10 5
© 2016 SmartAVI, Inc.

IR Function
Control devices like HDTVs, BluRay players, and more with
IR Cable Pin Assignment
IR Receiver (RX)
IR Emitter (TX)
6 © 2016 SmartAVI, Inc.
SWP-T10

Notes:
SWP-T10 7
© 2016 SmartAVI, Inc.

Many industry-leading companies have recognized the innovation and power of SmartAVI’s technologies
and have successfully implemented them within their systems. Users of SmartAVI technology include:
800.AVI.2131
Tel: [phone] Fax: [phone]
11651 Vanowen St. North Hollywood, CA 91605
SmartAVI.com
NOTICE
The information contained in this document is subject to
change without notice. SmartAVI makes no warranty of any
kind with regard to this material, including but not limited to,
implied warranties of merchantability and fitness for
particular purpose.
SmartAVI will not be liable for errors contained herein or for
incidental or consequential damages in connection with the
furnishing, performance or use of this material.
No part of this document may be photocopied, reproduced,
or translated into another language without prior written
consent from SmartAVI Technologies, Inc.
Designed and Manufactured in the USA