SMART-AVI DVX-4P User manual

Quad DVI-D and USB Extender
EXTEND FOUR DVI-D VIDEO
SIGNALS, USB 1.1,
STEREO AUDIO, AND RS-232
UP TO 275 FEET OVER
CAT5 CABLING
Quick Start Guide
VIDEO
Input Interface DVI-D (Single-Link)
Output Interface DVI-D (Single-Link)
Resolution 1920x1200 at 60Hz, resolution
up to 1280x1024 min. 75Hz
Supported 480p, 720p,1080i
Data Rate 1.65 Gbps
USB Data USB maximum data rate 12Mbps
USB compatibility 1.0 and 1.1
AUDIO
Signal Type Stereo Audio
Bandwidth 15MHz, 0dB
Impedance 10K Ohm
OTHER
RS-232 Full duplex, transparent to all baud
rates TXd, RXD, GROUND
System cable CAT6, STP x4; CAT6, 568B
Size TX/RX 17” (L) x 3.5” (W) x 1.70” (H)
Weight 8 Lbs
Power 110/120 V - 5 VDC - 4 A
NOTICE
The information contained in this document is
subject to change without notice. SmartAVI makes
no warranty of any kind with regard to this material,
including but not limited to, implied warranties of
merchantability and tness for particular purpose.
SmartAVI will not be liable for errors contained
herein or for incidental or consequential damages in
connection with the furnishing, performance or use of
this material.
No part of this document may be photocopied,
reproduced, or translated into another language
without prior written consent from SmartAVI
Technologies, Inc.
800.AVI.2131, 702.800.0005
2455 W Cheyenne Ave, Suite 112
North Las Vegas, NV 89032
SmartAVI.com
TECHNICAL SPECIFICATION
DVX-4P
WHAT’S IN THE BOX
PART NO. Q-TY DESCRIPTION
DVX-4P-TXS 1
Quad DVI-D, USB, Audio and
RS232 over CAT6 STP
Transmitter
DVX-4P-RXS 1 Quad DVI-D, USB, Audio and
RS232 over CAT6 STP Receiver
CCPWR06 2 PS5VD4A Power Supply
Quick Start
Guide 1

OVEVIEW
The DVX-4P can extend up to four DVI-D, USB 1.1, stereo
audio and RS-232 signals up to 220 feet using 4 CAT6
cables, while retaining clear video and audio quality (with
image resolution up to 1900 x 1200 at 60Hz).
FEATURES
• Top image quality at all resoluons
• Video resoluons up to 1900 x 1200 at 60Hz
(1280 x 1024 at 75Hz) up to 220 feet
• Internal DCC tables
• Distance: 275 feet with a CAT6 STP cable
• Compable with all operang systems
• Compable with all major KVM switches
• Rack mountable
• Supports up to 4 DVI-D sources
• Supports USB 1.1 keyboard and mouse
• Uses easy-to-install, inexpensive pair cable
• Data recovery for digital video
• Fully compliant with USB 1.1 specicaons
• Supports 1.5 and 12Mbps data rates
• External power adaptors for transmier and receiver
units
• Fully transparent (does not use any emulaon)
• Plug-and-play ready
1. Turn off a computer and a monitor
2. Connect DVI male to male cable between the computer and the transmitter
3. Connect a monitor or a projecter to the DVI port on the receiver
4. Connect a shielded CAT6 STP cable between port 1 on the transmitter and port 1 on the receiver
5. Repeat for 3 other ports
6. Connect the transmitter to the host using the A-B USB cable (included with the unit)
7. The A side of the connectorwould go to the computer host and the B side would be connected to the transmitter
8. Connect the receiver to the peripheral
9. Connect the CAT6 STP Cable
HARDWARE INSTALLATION
DVX-4P-TXS FRONT
DVX-4P-TXS BACK
DVX-4P-RXS FRONT
DVX-4P-RXS BACK