SmarTrike Xtend Bike User manual

Xtend Bike
Assembly instructions
20828279603
1
Australia
Usa
ENGLISH

Age 3 - 4yrs
Age 4 - 6yrs
Age 6 - 7yrs
Balance bike mode to pedal mode
Balance
Pedal
Bike
2

6mm
5mm
L
R
NOTE: This information is only available on the bicycle itself.
3
Handlebar
SeatBicycle body
Pedal mechanism
ReflectorPedal Bell
Chain cover
Back Front
Chain

A
BC
a
b
a
5MM
MIN
MAX
1
2
4
3
b
A. Connect the front and back halves of the bike.
B. Tighten the nut and screw to lock the pieces in place.
A. Insert the handlebar into the front fork of the bike.
B. Tighten the bold at the top of the handlebar to secure it in place.
To adjust the height of the seat,
turn the seat bolt counter-clockwise. Raise the seat to the desired height. To lock the seat in place,
turn the seat bolt clockwise and tighten.
Install the bike seat into the base of the bike.
Make sure to install the seat between the MIN and MAX lines located on the seat bar.
Please follow all the instructions completely and carefully.
Please read the entire manual through before starting assembly or maintenance.
In case you are not confident with assembling this unit, please refer to a local bike shop.
WARNING: Keep small components away from children during the assembly process.
NOTE: All of the directions (right, left, front, rear, etc.) provided in this manual are as seen by the rider riding the bicycle.
Do not dispose of the carton or other packaging parts until the assembly of the bicycle is complete in order to prevent
accidentally discarding components of the bicycle.
5mm
4

B
6mm
6mm
NOTE: This information is only available on the bicycle itself.
5
A
6mm
B
6mm
A
2
a
b
Front brake
Front brake
A. To install the brakes, pull back the silver bolt
to expose the brake line, and insert the end of
the brake line into the designated hole located
on the brake lever.
B. Tightly fasten the brake
line to the body of the brake handle.
C. Test the brakes to make sure they
are functioning.
B. To install the reflector on the front
of the bike, open the reflector’s ring,
wrap it around the handlebar facing
the front of the bike, and fasten the
screw.
,
To install the bell, open the bell’s ring,
wrap it a ound the handlebar near the brake
and fasten the scrow.
7
6
5

L
R
6mm
Turn the bicycle in an upside down .
Step 1:
Assembly parts
L
R
6mm
1
Turn the bike upside down.
6
Installing the Pedals

A
3
D
A
AB C
2
5mm
4
B
C
C
A. Using the provided Allen key,
remove the 3 screws in the footrest. B. Remove the footrest Save the screws you have just removed for future steps.
Remove the plastic ring covering the gear on the back wheel.
A. Install the chain on the large gear attached to the pedal mechanism. B. Install the other side of the chain on the small gear attached
to the rear wheel of the bike.
C. Position the pedal mechanism in place of the footrest.
7

5mm
5
A
6
Click
Click
C
B
D
6mm
6mm
5
A. In order to install the gear cover, remove the screw on the
back fork by the gear.
C. Click the cover into place
D. Return the screw and lock the gear cover in place.
B. Place the gear cover over the pedal mechanism.
Use the screws from the footrest to install the pedal mechanism.
8

.can be found on the bottom of the crank housing as shown
2
7
L
R
R
R
L
L
When installing the pedals, check the side indicators (L/R) on the pedals and pedal bars to make sure you are installing them correctly.
Once you have matched the right pedal to the right side, use the open wrench to attach the pedals to the pedal bars.
9

A
B
1
C
5mm
B
Extending the bike
A. In order to extend the frame of the the bike,
use the Allen key to loosen the bolt holding the
body together.
C. Re-fasten the bolt on the body of the bike.
B. Pull the front half of the bike away from the back half.
10

2
A
B
C
Min
6mm
6mm
A
A. To raise the handlebar, use the Allen key to loosen the bolt at the top of the handlebar.
B. Adjust the handlebar accordingly
C. Re-fasten the bolt at the top of
the handlebar.
11

www.smarTrike.com
By/Par
Find us at @smarTrike
12
20828279603
16