SMC Networks SMCWTVG User manual

38 Tesla
Irvine, CA 92618
Phone: [phone]
SMCWTVG
Wireless Travel Voice Gateway
Installation Guide
The easy way to make all your network connections
March 2006
Revision Number: R01 F1.0.6.x

Copyright
Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable.
However, no responsibility is assumed by SMC for its use, nor for any infringements of patents
or other rights of third parties which may result from its use. No license is granted by
implication or otherwise under any patent or patent rights of SMC. SMC reserves the right to
change specifications at any time without notice.
Copyright © 2006 by
SMC Networks, Inc.
38 Tesla
Irvine, CA 92618
All rights reserved.
Trademarks:
SMC is a registered trademark; and EliteConnect is a trademark of SMC Networks, Inc. Other
product and company names are trademarks or registered trademarks of their respective
holders.

i
Compliances
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected
• Consult the dealer or an experienced radio/TV technician for help
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
The antenna(s) used for this transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
IMPORTANT NOTE:
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance
of 20 centimeters (8 inches) between the radiator and your body. This transmitter must
not be co-located or operating in conjunction with any other antenna or transmitter.
Japan VCCI Class B

ii
EC Conformance Declaration
Marking by the above symbol indicates compliance with the Essential Requirements of
the R&TTE Directive of the European Union (1999/5/EC). This equipment meets the
following conformance standards:
• EN 60950-1 (IEC 60950-1) - Product Safety
• EN 300 328 - Technical requirements for 2.4 GHz radio equipment
• EN 301 489-1, EN 301 489-17 - EMC requirements for radio equipment
This device is intended for use in the following European Community countries:
Requirements for indoor vs. outdoor operation, license requirements and allowed
channels of operation apply in some countries as described below:
• In Italy the end-user must apply for a license from the national spectrum authority to
operate this device outdoors.
• In Belgium outdoor operation is only permitted using the 2.46 - 2.4835 GHz band:
Channel 13.
• In France outdoor operation is only permitted using the 2.4 - 2.454 GHz band: Channels
1 - 7.
• Austria • Belgium • Denmark
• Finland • France • Germany
• Italy • Luxembourg • Netherlands
• Norway • Spain • Sweden
• Switzerland • United Kingdom • Portugal
• Greece • Ireland • Iceland

iii
Contents
Chapter 1: Introduction 1-1
Package Checklist 1-1
Hardware Description 1-2
Component Description 1-3
Chapter 2: Connecting the Wireless Travel Voice Gateway 2-1
Internet Gateway 2-1
Wireless Client 2-2
Wireless Access Point 2-3
VoIP Telephony Functions 2-5
Appendix A: Troubleshooting A-1
Diagnosing LED Indicators A-1
Appendix B: Cables and Pinouts B-1
Twisted-Pair Cable Assignments B-1
10/100BASE-TX Pin Assignments B-1
Straight-Through Wiring B-2
Crossover Wiring B-2
RJ-11 Ports B-3
Appendix C: Specifications C-1
Physical Specifications C-1
Wireless Specifications C-2
VoIP Specifications C-2
Compliances C-3

iv
Contents

1-1
Chapter 1: Introduction
The Wireless Travel Voice Gateway SMCWTVG is a compact multi-funtion network
connection device. The unit provides secure wired and wireless high-speed data
and VoIP (Voice over Internet Protocol) communications through an Internet
connection.
The Wireless Travel Voice Gateway functions in the following operating modes:
• Secure VoIP Gateway
• IEEE 802.11b/g Wireless Access Point
• IEEE 802.11b/g Wireless Client
The Wireless Travel Voice Gateway’s capabilities make it ideal for business
travelers or home users. The device provides a secure Internet gateway function
between a cable/DSL modem connection and its wired LAN port and wireless
clients. The integrated VoIP ability offers voice communications over the Internet
from a wired or wireless connected PC, or by connecting a regular telephone set to
its PHONE port. It can function as an 802.11b/g Wi-Fi access point providing a
service to wireless clients. Or, it can function as a wireless client itself for PC
connections to other Wi-Fi networks.
In addition, the Wireless Travel Voice Gateway can automatically select the
operating mode based on its port connections, or it can be fully configured through
an easy-to-use web-browser management interface.
Package Checklist
The Wireless Travel Voice Gateway package includes:
* One Wireless Travel Voice Gateway
* Two RJ-45 Category 5 network cables
* One RJ-11 telephone cable (min 26 AWG)
* One Y-type USB power supply cable
* One AC power adapter with detachable plug
* This Quick Installation Guide
* Documentation CD (includes Installation Guide and Management Guide)
Inform your dealer if there are any incorrect, missing or damaged parts. If possible,
retain the carton, including the original packing materials. Use them again to repack
the product in case there is a need to return it.

Introduction
1-2
Hardware Description
Top Panel
Side Panels
Factory Default Reset Button
LAN Port
Power Socket
WAN Port
LINE Port
PHONE Port

Hardware Description
1-3
Component Description
WAN Port
The Wireless Travel Voice Gateway’s WAN port is a standard RJ-45 Ethernet
network port. It is for connecting the gateway to an Internet connection device, such
as an ADSL or cable modem. You can also connect the WAN port to a switch in an
Ethernet network that provides Internet access.
The WAN port can be attached directly to your cable/DSL modem using one of the
included Category 5 network cables. If you choose to use other, longer Category 5
network cables, be sure they conform to the specifications and pinouts provided in
Appendix B.
Note: The WAN port supports automatic MDI/MDI-X operation, which means you can
use the same “straight-through” network cable for connection to a cable/DSL
modem or Ethernet switch.
LAN Port
The Wireless Travel Voice Gateway’s LAN port is a standard RJ-45 Ethernet
network port that connects directly to your PC. It can also be connected to an
Ethernet switch or hub to support more than one user.
The LAN port can be attached directly to your PC using one of the included
Category 5 network cables. If you choose to use other, longer Category 5 network
cables, be sure they conform to the specifications and pinouts provided in
Appendix B.
Note: The LAN port supports automatic MDI/MDI-X operation, which means you can
use the same “straight-through” network cable for connection to a PC or an
Ethernet switch.
PHONE Port
The Wireless Travel Voice Gateway’s PHONE port is a standard RJ-11 telephone
port that connects directly to a standard (analog) telephone set. This allows a
regular telephone to be used for making VoIP calls over the Internet.
LINE Port
The Wireless Travel Voice Gateway’s LINE port is a standard RJ-11 telephone port
that connects directly to a Public Switched Telephone Network (PSTN) jack.

Introduction
1-4
LED Indicators
The Wireless Travel Voice Gateway includes three system status LED indicators
and two port LED indicators for each of the LAN and WAN ports, as described in the
following figures and tables.
LED Status Description
Power/Diag On Green Indicates that the system is working normally.
On Amber Systemrunningitspower-on-self-test.IftheLED remains
on amber for more than 20 seconds, it indicates system
errors.
Internet On Green Indicates the Wireless Travel Voice Gateway has
recieved an IP address from a DHCP server and can
connect to the Internet.
Off TheWirelessTravelVoiceGateway has no configured IP
address to connect to the Internet.
Wireless Slow Flashing
Green Indicates a wireless association (connection) with a strong radio signal.
Fast Flashing
Green Indicatesawireless association (connection) witha weak radio signal.
Off Indicatesnowirelessassociation(connection)ornoradio
signal
Power/Diag Internet Wireless