SMC Networks 8505T - annexe 1 User manual

SMC8505TX
SMC8508TX

38 Tesla
Irvine, CA 92618
Phone: [phone]
EZ Switch 10/100/1000
User Guide
From SMC’s EZ line of low-cost workgroup LAN solutions
July 2003
Pub. # 150000005200H R01

Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable.
However, no responsibility is assumed by SMC for its use, nor for any infringements of
patents or other rights of third parties which may result from its use. No license is granted by
implication or otherwise under any patent or patent rights of SMC. SMC reserves the right to
change specifications at any time without notice.
SMC Networks, Inc.
38 Tesla
Irvine, CA 92618.
All rights reserved. Printed in Taiwan
Trademarks:
SMC is a registered trademark; and EZ Switch is a trademark of SMC Networks, Inc. Other
product and company names are trademarks or registered trademarks of their respective
holders.

i
L IMITED W ARRANTY
Limited Warranty Statement: SMC Networks, Inc. (“SMC”) warrants its products to be
free from defects in workmanship and materials, under normal use and service, for the
applicable warranty term. All SMC products carry a standard 90-day limited warranty from
the date of purchase from SMC or its Authorized Reseller. SMC may, at its own discretion,
repair or replace any product not operating as warranted with a similar or functionally
equivalent product, during the applicable warranty term. SMC will endeavor to repair or
replace any product returned under warranty within 30 days of receipt of the product.
The standard limited warranty can be upgraded to a Limited Lifetime* warranty by registering
new products within 30 days of purchase from SMC or its Authorized Reseller. Registration
can be accomplished via the enclosed product registration card or online via the SMC Web
site. Failure to register will not affect the standard limited warranty. The Limited Lifetime
warranty covers a product during the Life of that Product, which is defined as the period of
time during which the product is an “Active” SMC product. A product is considered to be
“Active” while it is listed on the current SMC price list. As new technologies emerge, older
technologies become obsolete and SMC will, at its discretion, replace an older product in its
product line with one that incorporates these newer technologies. At that point, the obsolete
product is discontinued and is no longer an “Active” SMC product. A list of discontinued
products with their respective dates of discontinuance can be found at:
http://www.smc.com/index.cfm?action=customer_service_warranty.
All products that are replaced become the property of SMC. Replacement products may be
either new or reconditioned. Any replaced or repaired product carries either a 30-day limited
warranty or the remainder of the initial warranty, whichever is longer. SMC is not responsible
for any custom software or firmware, configuration information, or memory data of
Customer contained in, stored on, or integrated with any products returned to SMC pursuant
to any warranty. Products returned to SMC should have any customer-installed accessory or
add-on components, such as expansion modules, removed prior to returning the product for
replacement. SMC is not responsible for these items if they are returned with the product.
Customers must contact SMC for a Return Material Authorization number prior to returning
any product to SMC. Proof of purchase may be required. Any product returned to SMC
without a valid Return Material Authorization (RMA) number clearly marked on the outside
of the package will be returned to customer at customer’s expense. For warranty claims within
North America, please call our toll-free customer support number at [phone].
Customers are responsible for all shipping charges from their facility to SMC. SMC is
responsible for return shipping charges from SMC to customer.

L IMITED W ARRANTY
ii
WARRANTIES EXCLUSIVE: IF AN SMC PRODUCT DOES NOT OPERATE AS
WARRANTED ABOVE, CUSTOMER’S SOLE REMEDY SHALL BE REPAIR OR
REPLACEMENT OF THE PRODUCT IN QUESTION, AT SMC’S OPTION. THE
FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN
LIEU OF ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED,
EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE,
INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. SMC NEITHER ASSUMES NOR
AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER
LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION,
MAINTENANCE OR USE OF ITS PRODUCTS. SMC SHALL NOT BE LIABLE
UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THE
ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY
CUSTOMER’S OR ANY THIRD PERSON’S MISUSE, NEGLECT, IMPROPER
INSTALLATION OR TESTING, UNAUTHORIZED ATTEMPTS TO REPAIR, OR
ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE, OR BY
ACCIDENT, FIRE, LIGHTNING, OR OTHER HAZARD.
LIMITATION OF LIABILITY: IN NO EVENT, WHETHER BASED IN CONTRACT
OR TORT (INCLUDING NEGLIGENCE), SHALL SMC BE LIABLE FOR
INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE
DAMAGES OF ANY KIND, OR FOR LOSS OF REVENUE, LOSS OF BUSINESS, OR
OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE
SALE, INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE, OR
INTERRUPTION OF ITS PRODUCTS, EVEN IF SMC OR ITS AUTHORIZED
RESELLER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES
OR THE LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR
CONSUMER PRODUCTS, SO THE ABOVE LIMITATIONS AND EXCLUSIONS
MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS, WHICH MAY VARY FROM STATE TO STATE. NOTHING IN THIS
WARRANTY SHALL BE TAKEN TO AFFECT YOUR STATUTORY RIGHTS.
* SMC will provide warranty service for one year following discontinuance from the active
SMC price list. Under the limited lifetime warranty, internal and external power supplies, fans,
and cables are covered by a standard one-year warranty from date of purchase.
SMC Networks, Inc.
38 Tesla
Irvine, CA 92618

iii
C OMPLIANCES
FCC - Class B
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with instructions, may
cause harmful interference to radio communications. However, there is no guarantee that the inter-
ference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected
• Consult the dealer or an experienced radio/TV technician for help
EC Conformance Declaration - Class B
SMC contact for these products in Europe is:
SMC Networks Europe,
Edificio Conata II,
Calle Fructuós Gelabert 6-8, 2o, 4a,
08970 - Sant Joan Despí,
Barcelona, Spain.
This information technology equipment complies with the requirements of the Council
Directive 89/336/EEC on the Approximation of the laws of the Member States relating to
Electromagnetic Compatibility and 73/23/EEC for electrical equipment used within certain
voltage limits and the Amendment Directive 93/68/EEC. For the evaluation of the
compliance with these Directives, the following standards were applied:
RFI Emission: • Limit class B according to EN 55022:1998, IEC 60601-1-2 (EMC,
medical)
• Limit class A for harmonic current emission according to
EN 61000-3-2/1995
• Limitation of voltage fluctuation and flicker in low-voltage supply system
according to EN 61000-3-3/1995
Immunity: • Product family standard according to EN 55024:1998
• Electrostatic Discharge according to EN 61000-4-2:1995
(Contact Discharge: ±4 kV, Air Discharge: ±8 kV)
• Radio-frequency electromagnetic field according to EN 61000-4-3:1996
(80 - 1000 MHz with 1 kHz AM 80% Modulation: 3 V/m)

C OMPLIANCES
iv
Industry Canada - Class B
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital
apparatus as set out in the interference-causing equipment standard entitled “Digital Apparatus,”
ICES-003 of the Department of Communications.
Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux appareils
numériques de Classe B prescrites dans la norme sur le matériel brouilleur: “Appareils
Numériques,” NMB-003 édictée par le ministère des Communications.
Japan VCCI Class B
Safety Compliance
CSA/NRTL (C22.2.950, UL 1950)
EN60950, (IEC 950)
• Electrical fast transient/burst according to EN 61000-4-4:1995 (AC/DC
power supply: ±1 kV, Data/Signal lines: ±0.5 kV)
• Surge immunity test according to EN 61000-4-5:1995
(AC/DC Line to Line: ±1 kV, AC/DC Line to Earth: ±2 kV)
• Immunity to conducted disturbances, Induced by radio-frequency fields:
EN 61000-4-6:1996 (0.15 - 80 MHz with
1 kHz AM 80% Modulation: 3 V/m)
• Power frequency magnetic field immunity test according to
EN 61000-4-8:1993 (1 A/m at frequency 50 Hz)
• Voltage dips, short interruptions and voltage variations immunity test
according to EN 61000-4-11:1994 (>95% Reduction @10 ms, 30%
Reduction @500 ms, >95% Reduction @5000 ms)
LVD: • EN 60950 (A1/1992; A2/1993; A3/1993; A4/1995; A11/1997)
MDD: • IEC 60601-1

C OMPLIANCES
v
Wichtige Sicherheitshinweise (Germany)
1. Bitte lesen Sie diese Hinweise sorgfältig durch.
2. Heben Sie diese Anleitung für den späteren Gebrauch auf.
3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie keine Flüssigoder
Aerosolreiniger. Am besten eignet sich ein angefeuchtetes Tuch zur Reinigung.
4. Die Netzanschlu ßsteckdose soll nahe dem Gerät angebracht und leicht zugänglich sein.
5. Das Gerät ist vor Feuchtigkeit zu schützen.
6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen oder Fallen
könnte Beschädigungen hervorrufen.
7. Die Belüftungsöffnungen dienen der Luftzirkulation, die das Gerät vor Überhitzung schützt.
Sorgen Sie dafür, daß diese Öffnungen nicht abgedeckt werden.
8. Beachten Sie beim Anschluß an das Stromnetz die Anschlußwerte.
9. Verlegen Sie die Netzanschlußleitung so, daß niemand darüber fallen kann. Es sollte auch
nichts auf der Leitung abgestellt werden.
10. Alle Hinweise und Warnungen, die sich am Gerät befinden, sind zu beachten.
11. Wird das Gerät über einen längeren Zeitraum nicht benutzt, sollten Sie es vom Stromnetz
trennen. Somit wird im Falle einer Überspannung eine Beschädigung vermieden.
12. Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder Flüssigkeiten in das Gerät
gelangen. Dies könnte einen Brand bzw. elektrischen Schlag auslösen.
13. Öffnen sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen Sicherheit nur von
authorisiertem Servicepersonal geöffnet werden.
14. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu trennen und von einer
qualifizierten Servicestelle zu überprüfen:
a. Netzkabel oder Netzstecker sind beschädigt.
b. Flüssigkeit ist in das Gerät eingedrungen.
c. Das Gerät war Feuchtigkeit ausgesetzt.
d. Wenn das Gerät nicht der Bedienungsanleitung entsprechend funktioniert oder Sie mit
Hilfe dieser Anleitung keine Verbesserung erzielen.
e. Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt.
f. Wenn das Gerät deutliche Anzeichen eines Defektes aufweist.
15. Zum Netzanschluß dieses Gerätes ist eine geprüfte Leitung zu verwenden. Für einen
Nennstrom bis 6A und einem Gerätegewicht größer 3kg ist eine Leitung nicht leichter als
H05VV-F, 3G, 0.75mm
2
einzusetzen.
Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000 beträgt 70dB(A) oder
weniger.

C OMPLIANCES
vi

vii
TABLE OF CONTENTS
About the EZ Switch 10/100/1000 . . . . . . . . . . . . . . . . . 1
Description of Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Front and Rear Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
SMC8505T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
SMC8508T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Installing the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Mounting the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Stacking Switches
on a Flat Surface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Mounting Switches in a Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Connecting the Switch System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Making a Connection to an RJ-45 Port . . . . . . . . . . . . . . . . . . . . . . 5
Powering On the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Verifying Port Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Verifying System Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Physical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
EMC/Safety Compliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Diagnosing Switch Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Power and Cooling Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Cable Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
10BASE-T/100BASE-TX Pin Assignments . . . . . . . . . . . . . . . . . . . . . . 15
1000BASE-T Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
1000BASE-T Cable Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Cable Testing for Existing Category 5 Cable . . . . . . . . . . . . . . . . 17
Adjusting Existing Category 5 Cabling . . . . . . . . . . . . . . . . . . . . . 17

viii

1
A BOUT THE
EZ S WITCH 10/100/1000
The EZ Switch™ 10/100/1000, SMC8505T/SMC8508T are
high-performance Gigabit Ethernet switches designed for the network
core. It provides 5/8 full-duplex 1000BASE-T ports that can significantly
improve the performance of your network’s backbone, and deliver the
throughput needed to support a broad range of advanced network
applications. With 10/16 Gigabits of aggregate bandwidth, this
EZ Switch 10/100/1000 provides the quickest solution to meeting the
growing demands on your network’s limited resources.
Description of Hardware
The EZ Switch 10/100/1000 SMC8505T/SMC8508T is an 5/8-port
Gigabit Ethernet switch. The 10BASE-T/100BASE-TX/1000BASE-T
ports deliver dedicated 10/100/1000 Mbps links to each attached LAN
segment. All RJ-45 ports on this switch operate at 10, 100 or 1000 Mbps.
10/100 Mbps connections support auto-negotiation of speed, flow
control, and duplex mode. 1000 Mbps connections support
auto-negotiation of speed, duplex mode, and flow control, but only
operate at full duplex.
The RJ-45 ports also feature automatic MDI/MDI-X operation. This
means that you can use either straight-through or crossover cables
to connect to any other network device.

A BOUT THE EZ S WITCH 10/100/1000
2
Auto-negotiation is used to select the optimal transmission speed and
communication mode for each connection. With store-and-forward
switching and flow control, maximum data integrity is always maintained,
even under heavy loading. Easy installation and reliability make this
plug-and-play switch an ideal choice for delivering high speed Internet
access to multiple users.
The following figures show the components of this switch:
Front and Rear Panels
SMC8505T
SMC8508T
EZSwitch 10/100/1000
8505T
EZSwitch 10/100/1000
8505T
1A
EZSwitch 10/100/1000
8508T
EZSwitch 10/100/1000
8508T
1.25A

3
I NSTALLING THE S WITCH
Before installing the switch, verify that you have all the items listed under
“Package Contents.” Note that this switch can be installed on any suitably
large flat surface or in a standard EIA 19-inch rack.
Package Contents
The EZ Switch 10/100/1000 includes:
Mounting the Switch
This switch can be placed directly on your desktop, or mounted in a rack.
Before you start installing the switch, make sure you can provide the right
operating environment, including power requirements, sufficient physical
space, and proximity to other network devices that are to be connected.
Verify the following installation requirements:
• Power requirements: 100 to 240 VAC (± 10%) at 50 to 60 Hz (± 3Hz).
The switch’s power supply automatically adjusts to the input voltage
level.
• The switch should be located in a cool dry place, with at least 10 cm (4
in) of space on the sides for ventilation.
• Place the switch out of direct sunlight, and away from heat sources or
areas with a high amount of electromagnetic interference.
• EZ Switch 10/100/1000 (SMC8505T or SMC8508T)
• Four rubber foot pads • Appropriate DC power adapter
• Rack-mount bracket kit • This User Guide
• SMC Warranty Registration Card

I NSTALLING THE S WITCH
4
• If you intend to mount the switch in a rack, make sure you have all the
necessary mounting screws, brackets, bolts and nuts, and the right
tools.
• Check if network cables and connectors needed for installation are
available.
Stacking Switches
on a Flat Surface
The switch can be placed
anywhere there is enough flat
space, such as on a table or
desktop.
1. Stick the self-adhesive rubber foot pads (that come with this package)
on each of the 4 concave spaces located on the bottom of the first
switch.
2. Place the first switch on a firm flat surface where you want to install
the stack.
3. Repeat step 1 for each switch before stacking them. The rubber foot
pads cushion the switch against shock/vibrations and provide space
between each switch for ventilation.
Mounting Switches in a Rack
Please comply with the following
instructions to ensure that your
switch is securely mounted in the
rack.
1. Use a standard EIA 19-inch
rack.
2. Use the brackets and screws supplied in the rack mounting kit.
3. Use a cross-head screwdriver to attach the brackets to the side of the
switch.
EZSwitch10/100/1000
8508T
EZSwitch 10/100/1000
8508T
EZSwitch10/100/1000
8508T
EZSwitch 10/100/1000
8508T
EZSwitch10/100/1000
8508T
EZSwitch 10/100/1000
8508T
EZSwitch10/100/1000
8508T
EZSwitch 10/100/1000
8508T
EZSwitch10/100/1000
8508T
EZSwitch 10/100/1000
8508T

C ONNECTING THE S WITCH S YSTEM
5
4. Position the switch in the rack by lining up the holes in the brackets
with the appropriate holes on the rack, and then use the rack-mount
screws to mount the switch in the rack.
Connecting the Switch System
The EZ Switch 10/100/1000 provides 5/8 RJ-45 ports on this device.
Each of these ports supports connection to 10 Mbps Ethernet,
100 Mbps Fast Ethernet, or 1000 Mbps Gigabit Ethernet. In addition, they
are capable of operating at either half or full-duplex at 10 or 100 Mbps. At
1000 Mbps, only full-duplex operation is supported. The transmission
speed for each port is automatically set by the switch to match the highest
speed supported by the connected device. The transmission mode can be
set for each port using auto-negotiation (if also supported by the attached
device).
Making a Connection to an RJ-45 Port
Because all RJ-45 ports on these switches support automatic MDI/MDI-X
operation, you can use straight-through cables for all network connections
to PCs or servers, or to other switches or hubs. Note that auto-negotiation
must be enabled for automatic MDI/MDI-X pinout configuration.
1. Prepare the network devices you wish to network. Make sure you have
installed 1000BASE-T network interface cards for connecting to the
switch’s RJ-45 ports.
2. Prepare straight-through shielded or unshielded twisted-pair cables
with RJ-45 plugs at both ends. Use 100-ohm Category 3, 4 or 5 cable
for standard 10 Mbps Ethernet connections, 100-ohm Category 5
cable for 100 Mbps Fast Ethernet connections, or 100-ohm Category
5 or 5e cable for 1000 Mbps Gigabit Ethernet.
3. Connect one end of the cable to the RJ-45 port of the network
interface card, and the other end to any available RJ-45 port on the
switch. All RJ-45 ports support 10 Mbps, 100 Mbps and 1000 Mbps

I NSTALLING THE S WITCH
6
Ethernet connections. When inserting an RJ-45 plug, be sure the tab
on the plug clicks into position to ensure that it is properly seated.
Using the switch in a stand-alone configuration, you can network up to
8 end nodes.
Caution: Do not plug a phone jack connector into any RJ-45 port.
This may damage the switch. Instead, use only
twisted-pair cables with RJ-45 connectors that conform
with FCC standards.
Notes: 1. Make sure each twisted-pair cable does not exceed 100
meters (328 feet).
2. We advise using Category 5e cable for all network
connections or testing existing Category 5 cable to be
sure that it complies with the IEEE 802.3ab standards.
(See “1000BASE-T Cable Requirements” on page 17.)
Restrictions on Cascade Length - The IEEE 802.3 standard
recommends restricting the number of hubs (i.e., repeaters)
cascaded via twisted-pair cable to four; while IEEE 802.3u provides
even stricter recommendations for Fast Ethernet. Therefore, when
cascading devices other than this switch, please refer to the
accompanying documentation for cascade restrictions. However,
note that because switches break up the path for connected
devices into separate collision domains, you should not include
the
switch or connected cabling in your calculations for cascade
length involving other devices.

P OWERING O N THE S WITCH
7
Powering On the Switch
1. Plug the power cord into the power socket at the rear of the switch,
and the other end into a power outlet.
2. Check the LED marked Power on the front panel to see if it is on. The
unit will automatically select the setting that matches the connected
input voltage. Therefore, no additional adjustments are necessary
when connecting it to any input voltage within the range marked on
the rear panel.
3. The switch performs a self-diagnostic test upon power-on. (Note that
this test takes several seconds to complete.)
Note: The unit supports a “hot remove” feature which permits you to
connect or disconnect twisted-pair cables without powering off
the switch and without disrupting the operation of the devices
attached to the switch.

I NSTALLING THE S WITCH
8
Verifying Port Status
The front panel of the switch provides status LEDs for “at-a-glance”
system monitoring. The following table details the functions of the various
indicators:
Verifying System Operation
Verify that all attached devices have a valid connection. The switch
monitors the link status for each port. If any device is properly
connected to the switch and transmitting a link signal, the port
Port and System Status LEDs
LED Condition Status
Power On The switch is receiving power.
Ports
Link/Act On The port has established a valid network
connection.
Off The port has not established any network
connection.
Flashing Traffic is passing through the port.
1000M On Indicates that the port is transmitting or
receiving data at 1000 Mbps.
Off No link up at 1000M.
10/100M On Indicates that the port is transmitting or
receiving data at 100 Mbps.
Off Indicates that the port is transmitting or
receiving data at 10 Mbps.
EZSwitch 10/100/1000
8508T
EZSwitch 10/100/1000
8508T