Smith & Noble Deco Metal Hardware User manual

STEP BY STEP INSTALLATION INSTRUCTIONS
Ceiling Mount
Single Rod Set
Deco Metal
Hardware

2
800.248.8888
1smithandnoble.com
A Smooth Set-Up
We want you to love your new hardware and that includes
having a smooth installation experience. We suggest saving
this guide. If you encounter any difculties or questions,
please reach out to us for help. It’s why we’re here. Call us at
800.248.8888 for more info on installation.
We recommend you hold on to all packaging until your
hardware is fully installed. Should something go wrong (we
strongly doubt it), we want any potential returns to be a
painless as possible.
Customer Service Hours
Monday — Friday: 6am — 6pm PT
Saturday — Sunday: 7am — 4pm PT
smithandnoble.com
Everything
You Need
Table of Contents
Step 1 - Getting Started ..................................3
Overview - Ceiling Mount Single Rod Set .....................4
Step 2 - Marking Bracket Placement .................... 5 - 6
Step 3 - Attaching the Rod Connector......................7
Step 4 - Adding or Removing Carriers .....................8
Step 5 - Attaching Finials .................................9
Step 6 - Attaching the Rod to Bracket .....................10
Step 7 - Attaching Drapery to Rod ........................11
Accessories - Baton/Wand ...................................12
Care & Cleaning ...........................................13
Warranty ..........................................Back Cover

34
smithandnoble.com 800.248.8888
STEP 1 - GETTING STARTED OVERVIEW
Deco Metal Ceiling Mount Single Rod Set
SCREWS CEILING MOUNT
PENCIL
(NOT INCLUDED) CARRIERS
SCREWDRIVER
(NOT INCLUDED)
POWER DRILL
(NOT INCLUDED)
LEVEL
(NOT INCLUDED)
FINIAL
MOUNTING
BRACKET
MASTER
CARRIER CARRIERS
FINIAL
ROD QTY BRACKET QTY ROD WIDTH
1 2 12"— 60"
1 3 60¹⁄8"—96"
1 4 96¹⁄8"—106"
2 5 106¹⁄8"—156"
2 7 156¹⁄8"—212"
3 7 212¹⁄8"—216"
3 9 216¹⁄8"—252"
311 252¹⁄8"—288"
313 288¹⁄8"—318"
413 318¹⁄8"—336"
415 336¹⁄8"—384
Before you begin, check the accompanying diagram to make sure you have all the parts you need.
You’ll need to make sure the surface you intend to install your hardware is sturdy enough to
accommodate the brackets. If you’re screwing directly
into a surface this means locating wood studs that are
strong enough to securely bond with the included
screws. Otherwise, you’ll need to use a secure fastener
(as illustrated) but please note this piece is not included.
WALLBOARD OR PLASTER: Hollow wall applications: Use a secure fastener designed
speci cally for this purpose.
METAL: Prepare by pre-drilling holes and then using the included screws.
CONCRETE, STONE, BRICK OR TILE: Use a masonry drill and surface-speci c plugs, anchors, or
screws.When selecting a fastener be sure it’s designed to support the weight of the product being
installed (if you’re not sure, either give us a call or ask a professional at your local hardware store).
Once obtained, follow the fastener manufacturer’s instructions regarding proper installation.
TOOLS YOU WILL NEED TO INSTALL YOUR HARDWARE: Pencil, screwdriver, ¼" nut driver,
level, and a drill with a
7⁄64
"drill bit.
Note: It’s important to monitor the amount of pressure you apply when using a drill. If the screws
are too tight this may cause the screw itself to break off in the wall or window frame.
Parts & Tools
MOLLY
BOLT
SELF DRILLING
ANCHOR
TOGGLE
BOLT

56
smithandnoble.com 800.248.8888
STEP 2 - MARKING BRACKET PLACEMENT STEP 2 - MARKING BRACKET PLACEMENT
STEP 1:
Place bracket level against ceiling at
the marked spots. Using a pencil, lightly
draw a circle around the base of the
bracket onto ceiling (see Figure A).
Check to make sure the circles are level
& aligned with each other for each rod.
FIGURE A
Remove mounting plate and center it
inside of the circle outline on wall. Mark
the screw hole locations for all brackets
(see Figure B).
Attach the metal mounting plate to the
wall, aligning the holes in the plate with
the marks made in the previous step.
Be sure and attach the plate to the
ceiling with the appropriate mounting
hardware (It is always recommended to
try and attach to the wood studs inside
the ceiling. Where this is not possible
please use an anchor suitable to carry the
weight of your hardware selection as well
as your draperies and any accessories.)
Attach the bracket base onto the
mounting plate.
Place bracket base
on top of mounting
plate and thread in the
inside post and tighten
all the way.
MOUNTING
PLATE
FIGURE B
Mark all holes needed
showing locations of screw
holes for all brackets.

78
smithandnoble.com 800.248.8888
STEP 3 - ATTACHING THE ROD CONNECTOR STEP 4 - ADDING OR REMOVING CARRIERS
Depending on your order, you may
have received a rod connector.
A rod connector is the short piece of
metal placed inside each end of the
rods in a multi-segment system to
join them together.
Join track sections together and
fasten securely with set screws.
ROD
CONNECTOR
ROD
CONNECTOR
Adding or Removing
Carriers to the Rod
Your track rod will come with all master
carriers and regular carriers pre-
installed. If you need to add or take out
some carriers to reect same amount
of carriers to pin hooks in your drapery,
unscrew the endcap. Remove the end
stop click and either add or take out the
carriers needed.
Placing End Stops on the
Rod
Once all carriers have been placed in
the track, for split drapery (A), place
end stop click in between the rst
carrier from each end and the second
carrier so end of drape does not move
when drape is closed.
For one way draw drapery (B), place
end stop click in between the rst
carrier from the end and the second
carrier of the side you won’t be
opening it from so the end of drape
does not move when drape is closed.
END STOP
END STOP
MASTER
CARRIERS
(B) One Way Draw
End stop & Carrier
positions
CARRIERS
ADD OR
REMOVE
CARRIERS TRACK
END STOP
(A) Split Draw
End stop & Carrier
positions CARRIERS

910
smithandnoble.com 800.248.8888
STEP 5 - ATTACHING FINIALS
Attach finials by tightening the set
screw.
FINIAL
SET
SCREW
STEP 6 - ATTACHING THE ROD TO BRACKET
Attach Bracket Posts to
Rod (Track)
Slide outside posts onto rod (see
Figure A).
Align outside posts with Inside Posts.
Slide Outside Posts over Inside Posts
(see Figure B).
Once all Outside Posts including
Center Supports are in place, tighten
posts securely by turning clockwise.
Tighten set screws.
CARRIERS
OUTSIDE
POST
FINIAL
ROD
SET
SCREW
CARRIERS
OUTSIDE
POST
ROD
SET
SCREW
FIGURE A
TIGHTEN POST
CLOCKWISE
INSIDE
POST
OUTSIDE
POST
BASE
LOOSEN
SET SCREW
TIGHTEN
SET SCREWS
FIGURE B

11 12
smithandnoble.com 800.248.8888
STEP 7 - ATTACHING DRAPERY TO ROD
Insert drapery pin hooks into carriers
and master carriers.
Split Drapery
For Split drapery, start pinning from
the center and go towards the ends.
One Way Draw Drapery
For drapery opening from one side
only, start pinning from the opening
side towards the end.
SPLIT DRAPERY
BACK VIEW OF ROD
BACK VIEW OF ROD
ONE WAY DRAW DRAPERY
MASTER
CARRIER
MASTER
CARRIER
WAND
WAND
ROD
ROD
DRAPERY PIN
DRAPERY PIN
ACCESSORIES
Baton/Wand (optional)
Baton/Wand will be pre-attached to
the master carrier(s).
CLIP
BATON/
WAND
MASTER CARRIER
BATON/
WAND

13 14
smithandnoble.com 800.248.8888
Minimal care and cleaning is needed to maintain the beauty of your Hardware.
To Vacuum: Use brush or dust head attachment.
To Dust: Use soft, clean cloth.
CARE & CLEANING NOTES

© 2019 Smith & Noble Home, Inc. All Rights Reserved SN122019
Warranty Service
The enjoyment of your hardware should be everlasting, which is why our
products come with a limited lifetime warranty. The warranty applies to the
original owner, requires a proof of purchase (hang on to your receipt!) and
covers defects in material or craftsmanship. Hardware must have been properly
installed. We reserve the right to determine if your hardware warrants a repair
or a replacement. Visit smithandnoble.com/guarantee to see full details. In
need of warranty service? Call us at 800.248.8888 and we’ll arrange for a repair
or replacement ASAP.