Smith & Noble Fusion Hardware User manual

© 2019 Smith & Noble Home, Inc. All Rights Reserved SN0519
Warranty Service
The enjoyment of your hardware should be everlasting, which is why our
products come with a limited lifetime warranty. The warranty applies to the
original owner, requires a proof of purchase (hang on to your receipt!) and
covers defects in material or craftsmanship. Hardware must have been properly
installed. We reserve the right to determine if your hardware warrants a repair
or a replacement. Visit smithandnoble.com/guarantee to see full details. In
need of warranty service? Call us at 800.248.8888 and we’ll arrange for a repair
or replacement ASAP.
STEP BY STEP INSTALLATION INSTRUCTIONS
Wall Mount
Double Corner Rod Set
Fusion
Hardware

2
800.248.8888
1smithandnoble.com
A Smooth Set-Up
We want you to love your new hardware and that includes
having a smooth installation experience. We suggest saving
        
please reach out to us for help. It’s why we’re here. Call us at
800.248.8888 for more info on installation.
We recommend you hold on to all packaging until your
hardware is fully installed. Should something go wrong (we
strongly doubt it), we want any potential returns to be a
painless as possible.
Customer Service Hours
Monday — Friday: 6am — 6pm PT
Saturday — Sunday: 7am — 4pm PT
smithandnoble.com
Everything
You Need
Table of Contents
Step 1 - Getting Started ..................................3
Overview - Wall Mount Double Corner Rod Set ................4
Step 2 - Mounting the Brackets ........................ 5 - 6
Step 3 - Attaching the Rod Connector......................7
Step 4 - Attaching the Finials and Rings ................. 8 - 9
Step 5 - Securing Rod to Brackets .........................9
Accessories - Baton/Wand ...................................10
Accessories - Ball Tiebacks...................................11
Accessories - Hold Back .................................12 - 13
Care & Cleaning ...........................................14
Warranty ..........................................Back Cover

34
smithandnoble.com 800.248.8888
STEP 1 - GETTING STARTED OVERVIEW
Before you begin, check the accompanying diagram to make sure you have all the parts you
need. You’ll need to make sure the surface you intend to install your hardware is sturdy enough
to accommodate the brackets. If you’re screwing directly into a surface this means locating
wood studs that are strong enough to securely bond with the included screws. Otherwise,
you’ll need to use a secure fastener (as illustrated) but please note this piece is not included.
Tools & Parts Wall Mount Double Corner Rod Set
WALLBOARD OR PLASTER:
Hollow wall applications: Use a secure fastener designed

METAL:
Prepare by pre-drilling holes and then using the included screws.
CONCRETE, STONE, BRICK OR TILE:

be sure it’s designed to support the weight of the product being installed (if you’re not sure,
either give us a call or ask a professional at your local hardware store). Once obtained, follow
the fastener manufacturer’s instructions regarding proper installation.
TOOLS YOU WILL NEED TO INSTALL YOUR HARDWARE:
Pencil, screwdriver, ¼" nut driver, level, and a drill with a 764" drill bit.
Note: It’s important to monitor the amount of pressure you apply when using a drill. If the
screws are too tight this may cause the screw itself to break off in the wall or window frame.
MOLLY
BOLT
SELF DRILLING
ANCHOR
TOGGLE
BOLT
CEILING
BRACKETS
ROD QTY
(PER SIDE)
BRACKET QTY
(PER SIDE) ELBOW QTY ROD WIDTH
2 2 2 12"— 48"
2 3 8 4"—72"
2 4 2 4"—96"
4 5 2 4"—144"
4 7 2 4"—192"
6 7 2 4"—216"
6 9 2 4"—288"
811 24"—360"
813 24"—384"
FRONT
FINIAL
FRONT
ROD
CORNER
ELBOW
BRACKETS
BACK
ROD FRONT FINIAL
RINGS
WALLBOARD OR PLASTER:
Hollow wall applications: Use a secure fastener designed

METAL:
Prepare by pre-drilling holes and then using the included screws.
CONCRETE, STONE, BRICK OR TILE:

be sure it’s designed to support the weight of the product being installed (if you’re not sure,
either give us a call or ask a professional at your local hardware store). Once obtained, follow
the fastener manufacturer’s instructions regarding proper installation.
TOOLS YOU WILL NEED TO INSTALL YOUR HARDWARE:
Pencil, screwdriver, ¼" nut driver, level, and a drill with a 764" drill bit.
Note: It’s important to monitor the amount of pressure you apply when using a drill. If the
screws are too tight this may cause the screw itself to break off in the wall or window frame.
PENCIL
(NOT INCLUDED)
SCREWDRIVER
(NOT INCLUDED)
DRILL
(NOT INCLUDED)
LEVEL
(NOT INCLUDED)
SCREWS CORNER/ELBOW BRACKET
ALLEN WRENCHES
SET SCREWS
WALL MOUNT BRACKET

56
smithandnoble.com 800.248.8888
Mounting the Brackets
Check to make sure the circles are
level & aligned with each other.
Remove mounting plate and center
it inside of the circle outline on wall.
Mark the screw hole locations for all
brackets. See Figure B.
Attach the metal mounting plate to
the wall, aligning the holes in the
plate with the marks made in the
previous step, see figure B. Be sure
and attach the plate to the wall with
the appropriate mounting hardware.
(It is always recommended to try
and attach to the wood studs inside
the wall. Where this is not possible
please use a wall anchor suitable to
carry the weight of your hardwarese-
lection as well as your draperies and
any accessories.)
If using plastic expansion anchors,
pre-drill holes using 3/16" drill bit. If
drilling directly into a stud or wood
trim, pre-drill holes with 3/32" drill bit.
Screw on the decorative portion of
the bracket to the mounting base
until it is tight and the open side
of bracket faces up to the ceiling.
If the cup does not end facing up,
loosen the base screw to adjust and
repeat these steps for all brackets.
See Figure C.
STEP 2 - MOUNTING BRACKETS STEP 2 - MOUNTING BRACKETS
Mounting the Brackets
Place the panel on the left rod. To ensure it
drapes at the correct length, hold it up to the
spot you wish to install it; this will allow you
to raise or lower your treatment as desired.
After you’ve located the ideal location, use a
pencil to mark the wall where the top of the
rod is resting.
Repeat on the right side.
Remove the panel from the rods and then
center the rods over the window open-
ing at the desired height. Using the pen-
cil, mark where the ends of each rod are
positioned; if you’re using a center bracket,
note the middle point between these two
spots as well. If you have more than one
center bracket spread these evenly be-
tween the two brackets and centerpoint.
If you have a spliced rod, mark where the
splice is as well as on the wall since you will
need to add a bracket at this point, as well.
Measure 2” inward from the marks you’ve
made on both ends and mark those spots.
This is where the brackets will be installed.
Place bracket level against wall at the
marked spots. Using a pencil, lightly
draw a circle around the base of the
bracket onto wall, see Figure A.
CENTER ROD
CENTER ROD
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
XX
X
FIGURE B
Mark all holes needed
showing locations of screw
holes for all brackets.
MOUNTING
PLATE
MOUNTING
PLATE
DECORATIVE
PORTION OPEN SIDE(CUP) OF BRACKET
FACES UP
BACK PLATE
FIGURE A
BASE
SCREW BASE

78
smithandnoble.com 800.248.8888
Depending on your order, you may have
received a rod connector.
A rod connector is the short piece of met-
al tubing placed inside each end of the
rods in a multi-segment system to join
them together.
STEP 3 - ATTACHING THE ROD CONNECTOR STEP 4 - ATTACHING THE FINIALS & RINGS
ROD CONNECTOR
STEP 2:
Now slide the second rod segment
over the exposed end of the connector,
making sure there is no gap between the
two segments.
STEP 1:
On the open end of one-rod segment,
slide the connector halfway inside,
leaving the other half exposed.
ROD
SEGMENT
ROD
SEGMENT
ROD
CONNECTOR
ATTACH FINIAL
PLACE ONE RING
BETWEEN FINIAL
AND BRACKET
Attach the finial to one end of the rod by
sliding it on and attaching it using the
set screw. Place the required number of
rings on the rod, and then cap the oppo-
site end with the elbow and attaching it
using the set screw.
When placing the rod on the bracket,
if Drapery is opening from the center,
leave one ring between the finial/elbow
and bracket on each side. If the drapery is
opening from one side only, put the ring
between the finial/elbow and the brack-
et on the opposite side of where you are
opening from. This will prevent drapery
to be pulled all the way to one side or the
other when opening and closing it.
Repeat for the other side and back rods.
For treatments using rings
Attach the finial to one end of the rod by
sliding it on and attaching it using the set
screw. Position the drapery panels on
rod, and then cap the opposite end with
the elbow.
Repeat for the other side and back rods.
For treatments without rings
TIGHTEN
SET SCREW

910
smithandnoble.com 800.248.8888
STEP 5 - SECURING ROD TO BRACKETS ACCESSORIES
Baton/Wand (optional)
After your hardware is installed, attach
the baton to the eyelet of the first ring
by the clip.
Push clip through the
eyelet of the drapery clip
Baton/Wand
BATON/
WAND
CLIP
EYELET
DRAPERY
RING
Baton/Wand
Once the rod has been placed on the
brackets, secure the rod in place by
tightening the bracket set screw with
the allen wrench provided. SET
SCREW
SET
SCREW

11 12
smithandnoble.com 800.248.8888
ACCESSORIES ACCESSORIES
Tiebacks (optional)
BALL TIEBACK
STEP 1
In order to locate where to install your
tiebacks, measure the height of the
window and divide this by two. Using
the previous calculation, mark that
spot on the wall with a pencil.
To ensure you like the way the panel
drapes, gather one side and sweep
it over to the approximate proposed
location. Once you’re sure the tieback
is in the perfect location, use your
pencil to mark the spot to install it.
Measure the distance from the
bottom or top of the window to the
tieback to mark the other side and
ensure they’re even.
Now hold the tieback hardware on
the wall at the desired location and
rest a level above it, adjusting it until
it’s straight.
STEP 2:
Place tieback level against wall in
desired locations and attach to the wall.
Hold Back (optional)
STEP 1
In order to locate where to install your
tiebacks, measure the height of the
window and divide this by two.
Using the previous calculation, mark
that spot on the wall with a pencil.
To ensure you like the way the panel
drapes, gather one side and sweep it
over to the approximate proposed lo-
cation. Once you’re sure the tieback is
in the perfect location, use your pencil
to mark the spot to install it.
Measure the distance from the
bottom or top of the window to the
tieback to mark the other side and
ensure they’re even.
STEP 2:
Hook installation is an option depend-
ing on desired drapery style. When
using the hook option assemble the
" pole,
as shown to the left (A).
STEP 3:
" pole un-
til both holes line up as shown to the
left (B).
STEP 4:
To install the mount screw, place it
through the center of the 1½" pole &
the optional hook, as shown to the left
(C).
HOOK
MOUNT SCREW
A
B
C
X

13 14
smithandnoble.com 800.248.8888
CARE & CLEANING
Minimal care and cleaning is needed to maintain the beauty of your Hardware.
To Vacuum: Use brush or dust head attachment.
To Dust: Use soft, clean cloth.
ACCESSORIES
STEP 5:
Attach the Hold Back to the wall by
holding Hold Back assembly above the
hook hole location. Fingers placed be-
low this point or on the wall can become
pinched between the wall and the
Hold Back (D).
STEP 6:
Locate the Hold Back screw and
mount Hold Back, as shown at right (E).
STEP 7:
Assemble the Hold Back by placing
" pole. To secure
the finial to the pole tighten the 4 mm
set screw to the pole (F).
Keep fingers away
from edge and wall
during installation.
Keep fingers away
from edge and wall
during installation.
Hold Here
HOLD BACK FINIAL
D
E
F