SMITH SYSTEM GREEGUARD 24010 User manual

TEACHER DESK - DOUBLE DRAWER PED
If you have damaged or missing components please contact customer service.
MODEL 24010
03/2008www.smithsystem.com
800-328-1061
Form #179821

If you have damaged or missing components please contact customer service.
PARTS LIST
www.smithsystem.com
PART NUMBER:
03/2008
COLORS:
PART NUMBER:
QTY PER UNIT:
DESCRIPTION:
BLA; CMP; PLT
19180
2
DRAWER PED
COLORS:
PART NUMBER:
QTY PER UNIT:
DESCRIPTION:
BLA; CMP; PLT
19182
1
DOUBLE PED LEG SET (INCLUDES HDWR AND MODESTY PANEL)
COLORS:
CHOICE OF T-MOLD
CHOICE OF LAMINATE;
68657
1
30" X 60" TOPDESCRIPTION:
QTY PER UNIT:
800-328-1061
Form #179821

03/2008
If you have damaged or missing components please contact customer service.
1601-823-008128971#mroF
www.smithsystem.com
AND MAKE SURE THE LAMINATE IS FACE DOWN AND THE PRE-ATTACHED
MOUNTING PLATES ARE FACING UPWARDS.
LAY THE TOP UPSIDE DOWN, WITH THE CUT OF THE T-MOLD AT THE BACK1.
FORWARD (TOWARDS YOU).
2. REMOVE BOTH DRAWER PEDS FROM THEIR CARTONS. TURN THEM UPSIDE
DOWN SO THE KEYHOLE-SHAPED SLOTS ARE FACE DOWN.
3. SECURE DRAWER PED ON MOUNTING PLATE. ALIGN SLOTS ON DRAWER PED
TO KNOBS ON MOUNTING PLATE. BE CAREFUL NOT TO FORCE THE PARTS
TOGETHER. THE KNOBS ON THE PLATE SHOULD COMFORTABLY ALIGN WITH
THE SLOTS. ONCE THE PED IS SEATED ON THE PLATE, SLIDE THE PED
SLIDE FORWARD
T-MOLD CUT
FRONT
BACK
PRE-ATTACHED
PLATES
TURNED UPSIDE
DOWN
DRAWER PED
KEYHOLE-SHAPED
SLOTS
FRONT
BACK

If you have damaged or missing components please contact customer service.
4. REPEAT STEPS 2 AND 3 WITH THE REMAINING DRAWER PED.
5. ATTACH LEGS TO DRAWER PEDS USING CONNECTOR BOLTS
SLIDE FORWARD
REPEAT WITH OTHER LEG
03/2008
www.smithsystem.com
800-328-1061
Form #179821
INSERT BOLT HERE
INSERT BOLT HERE
WITH LEG SET)
HARDWARE PACK
(PROVIDED IN BOX
35MM CONNECTOR BOLTS (4 PER SIDE)

If you have damaged or missing components please contact customer service.
6. ATTACH PANEL TO DRAWER PEDS.
7. ATTACH PANEL TO TOP.
03/2008www.smithsystem.com
800-328-1061
Form #179821
(PROVIDED IN BOX
WITH LEG SET)
HARDWARE PACK
MACHINE SCREWS TO ATTACH PANEL
TO DRAWER PEDS
SCREWS
ATTACH USING
TWO SHEET METAL
HARDWARE PACK
(PROVIDED IN BOX
WITH LEG SET)
USING THE 4 MACHINE SCREWS PROVIDED IN THE
ATTACH PANEL TO THIS DRAWER PED
HARDWARE PACK
AND THEN TO OTHER DRAWER PED

9. THE UNIT IS NOW ASSEMBLED. YOU SHOULD NOT HAVE ANY REMAINING SCREWS
IN THE HARDWARE PACK. TIGHTEN THE MACHINE SCREWS AND THE SHEET METAL
10. USING THE HELP OF AT LEAST ONE OTHER PERSON, TURN THE UNIT OVER (UPRIGHT).
ARE PROVIDED TO ASSIST TIGHTENING THE CONNECTOR BOLTS.
SCREWS USING AN ELECTRIC DRILL AT THE LOWEST TORQUE SETTING. HEX KEYS
If you have damaged or missing components please contact customer service.
www.smithsystem.com
ACROSS THE FLOOR OR ROCKING THE DESK ON 2 OF THE 4 LEGS WILL WEAKEN THE
03/2008
INTEGRITY OF THE ASSEMBLY.
NOTE: USE CAUTION WHEN REPOSITIONING THE UNIT AT ANY TIME. DRAGGING THE DESK
800-328-1061
Form #179821
8. ATTACH THE LEGS TO THE TOP.
A
WITH LEG SET)
HARDWARE PACK
(PROVIDED IN BOX
2.5" SCREWS
DETAIL A
SCALE 1 : 4
USE 2.5" SCREWS
TO ATTACH EACH LEG
TO THE TOP.
3 SCREWS PER LEG