Target Windham WNBUFFETBL User manual

>>
© 2019 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.
windham
bu󰀨et
assembly instructions
style # WNBUFFETBL (teal)
dpci # 249-04-2372
tcin # 50760877
style # WNBUFFETGY (gray)
dpci # 249-04-2373
tcin # 50760878
style # WNBUFFETBK (black)
dpci # 249-04-2375
tcin # 50760880
style # WNBUFFETWH (shell)
dpci # 249-04-2376
tcin # 50760881
style # WNBUFFETOV (overcast)
dpci # 249-04-4742
tcin # 53321691

2
Congratulations on your latest Target purchase.
Now what? Don’t start sweating over this box of parts. This will be easy. We did the hard work for you.
All you need to do is follow our simple instructions and you’ll be on your way to transforming your
room in no time. Good luck—though we’re condent you won’t need it.
before you begin
1. Check for damaged or missing parts. Call 1-855-MYTGTHOME (855-698-4846) to order missing supplies.
2. Use the carton as a working surface to prevent product damage during assembly.
3. Gather all tools prior to assembly.
4. It is recommended to have 2-people for assembly.
tools needed

3
table of contents
introduction 2
hardware 4
parts list 5
how to use the cam lock system 6
assembly 7-18
how to adjust door alignment 19
QUESTIONS? Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and DPCI number ready when calling.

4
hardware
(H1) x 34
large wooden dowel
(H2) x 16
cam bolt
(H3) x 16
cam
(H4) x 27
small pan head screw
(H5) x 8
small at head screw
(H6) x 10
large at head screw
(H7) x 2
magnet catch
(H8) x 4
bolt
(H9) x 4
lock washer
(H10) x 4
knob
(H11) x 4
knob bolt
(H12) x 8
shelf support
(H13) x 2
small cam bolt
(H14) x 2
small cam
(H15) x 1
38mm wall screw
(H16) x 6
washer
(H17) x 1
wall anchor
(H18) x 1
wall strap
(H19) x 1
allen wrench
(H20) x 1
large pan head screw

55
exploded diagram
ITEM DESCRIPTION QUANTITY
1 top panel 1
2 left side panel 1
3 right side panel 1
4 bottom panel 1
5 back panel 1
6 partition 1
7 adjustable shelf 2
8 front rail 1
9 left door 1
10 right door 1
11 drawer face 1
12 left drawer side 1
13 right drawer side 1
14 drawer back 1
15 drawer bottom 1
16 drawer support 2
17 rear rail 1
18 rear upper rail 1
19 center foot 1

6
how to use the cam lock system
1.
Screw cam bolt into panel
2.
Align cam bolt(s) with cross-bored
hole(s) and insert all the way until
panels are ush
3.
Push cam into panel - arrow feature
on cam top points to panel edge
4.
Rotate cam(s) clockwise 180° to
lock panels together
5.
Panels should be tight against each
other and connection should be rigid
1. 2. 3.
4. 5.

7
step 1: attach partition to bottom panel
(H1) x 2
wooden dowel
(H2) x 2
cam bolt
(H3) x 2
cam
1.1. Carefully tap small wooden dowels into place in bottom panel. Leave 1/2” of the dowels sticking out.
1.2. Screw-In cam bolts must be screwed down ush in bottom panel.
1.3. Refer to page 6 for instructions on how to use the cam lock system. Do not over tighten bolts.
nished edge
front

8
step 2: attach center foot to bottom panel
2.1. Align center foot with pre-drilled hole to attach to bottom panel.

99
step 3: attach front rail and rear rail to partition
(H1) x 2
wooden dowel
(H2) x 2
cam bolt
(H3) x 2
cam
(H4) x 4
small pan
head screw
(H7) x 2
magnet catch
3.1. Align pan head screws with pre-drilled holes to attach door magnets to front rail. Do not over tighten screws.
3.2. Carefully tap small wooden dowels into place in front rail and rear rail. Leave 1/2” of the dowels sticking out.
3.3. Screw-In cam bolts must be screwed down ush in front rail and rear rail.
3.4. Refer to page 6 for instructions on how to use the cam lock system.
3.5. Do not over tighten bolts.
nished edge
nished edge
(H4) x 4
small pan
head screw
(H7) x 2
magnet catch
(H1) x 2
wooden dowel
(H2) x 2
cam bolt
(H3) x 2
cam

step 4: attach left side panel
(H1) x 8
wooden dowel
(H2) x 5
cam bolt
(H3) x 5
cam
4.1. Carefully tap small wooden dowels into place in left side panel. Leave 1/2” of the dowels sticking out.
4.2. Screw-In cam bolts must be screwed down ush in left side panel.
4.3. Refer to page 6 for instructions on how to use the cam lock system. Do not over tighten bolts.
10
nished edge
nished edge