SMITH SYSTEM 11160 User manual

For Assistance in assembling product, missing or damaged parts,
or to place an order, please contact customer service at 800-328-1061
You may also place your order online at
www.smithsystem.com
Form# 179803 02/2014
Access Station
Assembly Instructions
Models:
11160 11140
11161 11141
11162 11142
11163 11143
11164 11144
11165 11145
11166 11146

For Assistance in assembling product, missing or damaged parts,
or to place an order, please contact customer service at 800-328-1061
You may also place your order online at
www.smithsystem.com
Form# 179803 02/2014
Hardware and Components
P/N: 70054
#10X3/4” Wood Screw
P/N: 70867
(QTY: 4)
Connector Bolt ¼-20X23mm
P/N: 70869
(QTY:4)
Connector Nut ¼-20X17mm
P/N: 77813
(QTY:2)
Hex Key Allen Wrench 3/16
P/N: 77741
(QTY: 8)
3/8-16X.625 ½Dog Socket Screw
Planner Leg Set
(QTY: 1 Set)
Wire Manager With Door and Lock
(QTY: 1)
Table Top
(Qty: 1)
Key Set
URGENT: Please make sure you
have received all hardware and
components before assembling
product

For Assistance in assembling product, missing or damaged parts,
or to place an order, please contact customer service at 800-328-1061
You may also place your order online at
www.smithsystem.com
Form# 179803 02/2014
Replacement Hardware Packs
11140 –69709 ZINC/BLA-R 11160 –69709 ZINC/BLA-R
11141 –69709 ZINC/BLA-R 11161 –69709 ZINC/BLA-R
11142 –67607 ZINC/BLA-R 11162 –69709 ZINC/BLA-R
11143 –67607 ZINC/BLA-R 11163 –69709 ZINC/BLA-R
11144 –69709 ZINC/BLA-R 11164 –69709 ZINC/BLA-R
11145 –69709 ZINC/BLA-R 11165 –69709 ZINC/BLA-R
+ 69718 ZINC/BLA-R 11166 –69709 ZINC/BLA-R
11146 –69709 ZINC/BLA-R
+ (2) 69718 ZINC/BLA-R
Assembly Instructions
Step 1: Attach the (2) PSD legs using (4) Connector bolts and nuts which are located in your
hardware pack. Do not fully tighten the screws, until the table is fully assembled.
Step 2: Place the table top on a smooth, clean surface with the bottom facing up. Align the
assembly from step one with the predrilled holes in the larger top. Verify the alignment before
moving to step 3.

For Assistance in assembling product, missing or damaged parts,
or to place an order, please contact customer service at 800-328-1061
You may also place your order online at
www.smithsystem.com
Form# 179803 02/2014
Step 3: Attach the PSD legs using (4) Truss head screws to the table top through the predrilled
holes. Do not place the screws in the back two holes of the leg (See drawing 3A). Then, screw
the wire manager into the table top using the provided wood screws (See drawing 3B). Now, go
back and tighten the connector bolts referenced in Step 1.
Step 4: Adjust the PSD leg inserts to the desired height and secure with (8) 3/8-16X.625 half dog
nut screws (2 per leg). Use the provided allen wrench to loosen and tighten the screws.
Drawing 3A
Drawing 3B
Step 5: With help, flip the desk into its upright position. Your access
station is now ready for use.