SMITH SYSTEM Silhouette Standard User manual

Assembly Instructions
Silhouette Standard & XL Sit-Stand Desks
If you have damaged or missing components,
please contact customer service at 1-800-328-1061
Document #: 179690 REVISED: 01/2022

Hardware and Components
Document #: 179690 REVISED: 01/2022
SIT-STAND BASE
(PN: 60058)
QTY. 1
SIT-STAND COLUMN
(PN: 60060)
QTY. 1
CASTER
(PN: 17576)
QTY. 4
#10 X 5/8” PAN HEAD
WOOD SCREW
(PN: 60059)
QTY. 8
SIT-STAND DESK TOP
(PN: 01630
PN: 01631 SHOWN
PN: 01632)
QTY. 1
BUTTERFLY PLATE
(PN: 60058)
QTY. 1
5MM ALLEN WRENCH
(PN: 60059)
QTY. 1
M6 X 1.0MM X 20MM
SOCKET HEAD BOLT
(PN: 60059)
QTY. 3
M6 X 1.0MM X 10MM
SOCKET HEAD BOLT
(PN: 60059)
QTY. 8
PLASTIC LOOP CLAMP
(PN: 60059)
QTY. 2
CASTER WRENCH
(PN: 17576)
QTY. 1
For Standard Sit-Stand Desks

Hardware and Components
Document #: 179690 REVISED: 01/2022
SIT-STAND XL BASE
(PN: 60117)
QTY. 1
SIT-STAND COLUMN
(PN: 60060)
QTY. 1
CASTER
(PN: 17576)
QTY. 4
#10 X 5/8” PAN HEAD
WOOD SCREW
(PN: 60118)
QTY. 12
SIT-STAND DESK TOP
(PN: 01634
PN: 01635 SHOWN)
QTY. 1
XL BUTTERFLY PLATE
(PN: 60117)
QTY. 1
5MM ALLEN WRENCH
(PN: 60118)
QTY. 1
M6 X 1.0MM X 20MM
SOCKET HEAD BOLT
(PN: 60118)
QTY. 3
M6 X 1.0MM X 10MM
SOCKET HEAD BOLT
(PN: 60118)
QTY. 8
PLASTIC LOOP CLAMP
(PN: 60118)
QTY. 2
CASTER WRENCH
(PN: 17576)
QTY. 1
For XL Sit-Stand Desks

Special Notes:
•TOOLS REQUIRED:
•Drill w/#2 Phillips driver bit, or #2 Phillips head screwdriver.
•OPTIONAL TOOLS:
•Drill w/5mm hex driver bit.
•Check that all components are accounted for and undamaged before assembling.
•Please assemble the product in a clean and dry area.
•Clean the product with a mild cleaner and a damp cloth.
Document #: 179690 REVISED: 01/2022

2. For the standard sit-stand desks, position the butterfly plate, with the counterbored
holes facing up, to line up with the pilot holes in the top as shown. Install the four
#10 x 5/8” Wood Screws to secure the plate to the top. Do NOT exceed torque
setting 16 when installing the screws! Doing so can potentially lead to product
failure!
Assembly Instructions
Document #: 179690 REVISED: 01/2022
1. Place wood top on clean smooth surface upside down with the pilot holes facing up.
2. For the XL sit-stand desks, position the butterfly plate, with the counterbored holes
facing up, to line up with the pilot holes in the top as shown. Install the eight #10 x
5/8” Wood Screws to secure the plate to the top.
A.
B.

Document #: 179690 REVISED: 01/2022
3. Position the column over the butterfly plate so that the eight holes line up. Make sure
that the activation cable is coming out of the side of the column as shown. Secure the
column to the butterfly plate using the eight M6 x 10mm Socket Head Bolts with the
5mm Allen Wrench provided or with an optional drill with 5mm hex driver bit. Line up
the activation handle with the two holes on the top and secure it with two #10 x 5/8”
Wood Screws.
4. Place the two Plastic Loop Clamps on the cable by opening the split side and sliding it
over the cable. Place them along the cable near the two holes in the top.

Document #: 179690 REVISED: 01/2022
5. Secure the two Plastic Loop Clamps to the top by installing two #10 x 5/8” Wood
Screws.
6. Insert the base onto the column making sure the longer legs face the edge of the
table with the activation handle and that the three holes on the base line up with the
three holes on the column. Secure the base to the column using the three M6 x
20mm Socket Head Bolts with the 5mm Allen Wrench provided or with an optional
drill with 5mm hex driver bit.

Document #: 179690 REVISED: 01/2022
7. Install the four casters into each end of the base using the caster wrench provided.
ASSEMBLY COMPLETE
8. Flip the Sit-Stand Desk over.