Smiths Medical CADD-Prizm VIP User manual

Medical design mark are trademarks of Smiths Medical. The symbol ® indicates
the trademark is registered in the U.S. Patent and Trademark Office and certain
MPAUCA-1576
AB
C
D
E
F
G
H
CADD®-Prizm VIP
Ambulatory Infusion Pump
Model 6100 and 6101
Quick Reference Card for Clinicians
Using the Å(Help) Key
INTERMITTENT LOCK LEVEL 0
AGreen indicator light: blinks when pump is running
BAmber indicator light: blinks when pump is
stopped or alarming
CPolemount bracket recess (back of pump)
DPower jack (for power pack or AC adapter)
EData in/out jack (for printer or modem cable)
FBattery compartment (side of pump)
GCassette (part of reservoir or
administration set that attaches to pump)
HAir Detector
PRODUCT(S) DESCRIBED MAY NOT BE LICENSED OR AVAILABLE FOR SALE IN
For information about a screen or message on the pump
display, press ? key.
1. If ? → appears in lower right corner, press ? to see
more help.
2. Press NEXT to exit help.
3. Please read the Instructions for Use or Operator’s
Manual supplied with the product for detailed
instructions, warnings, and cautions on the safe use of
the product.

Keypad
STOP/START Stops and starts the pump
LOCK Displays or changes lock level
(security level)
?Help key: displays more information about
a screen
ENTER Sets new value; selects choice from menu;
clears screen
NEXT Advances to next programming screen;
backs out of an option or menu
DOSE Inoperable in TPN delivery mode
OPTIONS Displays the Options Menu, pages through
options
´Answers yes; increases values on
programming screen; pages through
menus; pages through event log
ÎAnswers no; decreases values on
programming screen; pages through
menus; pages through event log
PROGRAMMING / Setup Sequence
To go to the next programming screen without changing a
displayed setting, press NEXT. During programming, the
pump may ask you to confirm certain settings; press ´or Î
as appropriate.
Battery must
be installed;
pump must be
stopped and in
Lock Level 0.
1. On Main Screen, press NEXT.
Enter Reservoir
Volume
2. Press ´or Îto select desired
Reservoir Volume.
3. Press ENTER
Enter Dose
Volume
4. Press ´or Îto select desired Dose
Volume.
5. Press ENTER
Enter Dose
Volume
6. Press ´or Îto select desired Dose
Volume.
7. Press ENTER.
Enter Dose
Period
8. Press ´or Îto select desired Dose
Period.
9. Press ENTER.
Enter KVO Rate 10. Press ´or Îto select desired KVO
Rate.
11. Press ENTER.
WARNING: This Quick Reference Card should be used
by clinicians only. Do not permit patients to have
access to this card, as the information would allow
access to all programming and operating functions.

Time
Duration
KVO KVO
Delay
(using Next Dose
Start Time)
Dose
Volume
Cycle
Duration
DoseDose
PROGRAMMING / Setup Sequence (Continued)
Enter Next
Dose Start
Time
1. Press ´or Îto select desired dose
start time and date, or “immediate” if
appropriate.
2. Press ENTER.
3. Verify the start time and press ´if
correct. To re-enter the start time,
press Î.
Verify Dose rate Pump automatically calculates rate. Verify
that the cassette attached is appropriate
for the dose rate. (If rate is greater than
125 mL/hr, a CADD-PrizmÒ…ÆÓÌÏÎ high
volume administration set must be used.)
4. Press NEXT.
Clear Milliliters
Given
5. Press ENTER to clear the amount
given; this updates the date and time
markers.
Check Air
Detector Status
6. If air detector is attached, check the
Air Detector status, then press NEXT.
Review
Program
7. Press NEXT repeatedly to review
program.
Follow steps for attaching cassette, priming fluid path,
starting pump.
Pump Operations
To Change Lock
Level
1. Stop the pump.
2. Press LOCK.
3. Press ´or Îuntil desired lock level
appears.
4. Press LOCK.
5. Press ´or Îuntil lock level code
appears.
6. Press LOCK.
To Start or Stop
Pump
1. Press STOP/START.
2. Press ´
if the pump is stopped during a dose, the
sub-sequent doses are delayed by the
amount of time the pump is stopped. if
the pump is stopped during delivery at the
KVO rate, the start times of subsequent
doses are not affected.
Intermittent Infusion Cycle

Pump Operations (Continued)
To View Time
Remaining
Time remaining is the amount of time
remaining to deliver the current dose
and dose cycle.
1. Press OPTIONS.
2. Press ´or Îuntil Immediate
Taper-Down appears.
3. Press ENTER.
NOTE: if dashes appear in place of times,
the dose has been delayed by the Next
Dose start Time.
To Change
Next Dose
Start Time
Pump must be in LL0.
1. Stop the pump.
2. Press NEXT until Next Dose Start
Time appears.
3. Press ´or Îto select desired dose
start time and date, or “immediate”
if appropriate.
4. Press ENTER.
5. Verify the start time and press ´if
correct. To re-enter the start time,
press Î.
To Set Time
of Day
Pump must be stopped and in LL0.
1. Press OPTIONS.
2. Press ´until Time option appears.
3. Press ENTER.
4. Press ´or Îto select desired time.
5. Press ENTER.
6. Press ´.
To Set Date Pump must be stopped and in LL0.
1. Press OPTIONS.
2. Press ´until Date option appears.
3. Press ENTER to display Date screen.
4. Press ´or Îto select date.
5. Press ENTER.
6. Press ´.
To Set
AutoLock
AutoLock automatically changes lock
level to LL1 or LL2 when pump is started
in LL0. To change AutoLock setting,
pump must be stopped and in LL0.
Press ENTER.
1. Press OPTIONS.
2. Press ´until AutoLock
option appears.
3. Press ENTER to display
AutoLock screen.
4. Press ´or Îto select LL1 or
LL2 or Not In Use.
5. Press ENTER.
6. Press ´.

Changing the Cassette
To Remove
Used
Cassette
1. Stop the pump.
2. Close all tubing clamps.
3. If necessary, use key to unlock used
cassette.
4. Use side of key or coin to unlatch used
cassette.
5. Disconnect tubing from patient.
6. Remove and discard used cassette.
To Attach
New
Cassette
7. Close tubing clamp.
8. Insert new cassette hooks into pump’s
hinge pins.
9. Place pump with cassette on firm
surface and push down on top of pump.
10. Use coin or side of key to latch cassette.
11. The mark on latching button must line
up with solid dot on side of pump.
WARNING: Attach the cassette properly. A
detached or improperly attached cassette
could result in unregulated gravity
infusion of medication from the fluid
container or a reflux of blood. If
you are using a CADD®administration
set or CADD™ medication cassette
reservoir that does not have the flow
stop feature, you must use a CADD®
extension set with anti-siphon valve
or a CADD®administration set with
either an integral or add-on anti-siphon
valve to protect against unregulated
gravity infusion that can result from an
improperly attached cassette.
12. Gently twist and pull on cassette to
make sure it is attached properly.
13. If Reset Reservoir to — mL? appears,
press ´if appropriate.
14. When Prime Tubing? appears,
open tubing clamp and press ´
if appropriate. Follow priming
instructions on pump’s screen.
When primed, close tubing clamp.
15. If applicable, thread tubing through
Air Detector.
16. If AutoLock not in use / Change Lock
Level from LL0? appears, press ´.
Change the lock level to LL1 or LL2
(see To Change Lock Level).
17. When Start the Pump? appears,
connect new tubing to patient’s
access site, open tubing clamp,
and press ´.

Programming Screens
Reservoir Volume Volume of fluid in filled reservoir
Dose Volume Volume of dose in milliliters
Dose Duration Time period over which dose will
be delivered
Dose Cycle Time from the start of one dose to
the start time of the next dose
KVO Rate Keep Vein Open rate allows delivery
of a minimal amount of drug to
maintain catheter patency
Next Dose Start
Time
Date and time designated to start
delivery of next dose
Dose Rate Rate at which dose will be delivered
(automatically calculated)
Milliliters Given Displays total amount delivered
since date and time shown
Air Detector
Status
Shows whether Air Detector is
required, turned on or off
(appears if Air Detector is attached)
Alarms & Troubleshooting
The CADD-Prizm®pump signals with audible alarms and
messages on the display when a condition requires your
attention. In addition to referring to this table, use the ? key
while the alarm is occurring for information about
the alarm and corrective action.
Reservoir
Volume Low
Level of fluid in the reservoir
is low. Prepare to install a
new reservoir
Reservoir
Volume Zero
Reservoir volume is 0.0 ml.
Press NEXT to stop alarm.
Install new reservoir
if appropriate.
Priming the Fluid Path Using the Prime Option
The priming feature is available either:
a. when you attach a cassette (above), or
b. in the Options Menu. To access the
Prime option in the Options menu:
Pump must be in LL0 or LL1.
1. Stop the pump.
2. Press OPTIONS.
3. Prime should be displayed; press ENTER.
4. Follow priming instructions on pump’s screen.
To Reset Reservoir Volume Without Changing Cassette.
1. Stop the pump.
2. Press NEXT to display Reservoir Volume screen.
3. Press ENTER.
4. If message appears asking you to reset the Reservoir
Volume, press ´.

Find your local contact information at
www.smiths-medical.com/customer-support
Smiths Medical is part of the global technology business smiths group plc.
CADD, CADD-Prizm, Medication Cassette Reservoir Design and the Smiths
Medical design mark are trademarks of Smiths Medical. The symbol ® indicates
the trademark is registered in the U.S. Patent and Trademark Office and certain
other countries. Product referenced is CE-marked.
©2017 Smiths Medical. All rights reserved. IN19811EN-052017
Alarms & Troubleshooting (Continued)
9-volt
Battery Low
9-volt battery is low but
pump is operable.
Change battery soon.
9-volt Battery
Depleted
9-volt battery is depleted and
cannot operate pump;
install fresh battery immediately.
High Pressure Possible blockage downstream (between
pump and patient), clamp or kink in fluid
path. Find cause and remove blockage to
continue. Or, press STOP/START to stop
pump and silence alarm; remove blockage
and restart pump.
Upstream
Occlusion
(Model 6101
only)
Fluid is not flowing from the reservoir
to the pump. Check for a kink, a closed
clamp or an air bubble in tubing between
reservoir and pump. Press STOP/START
to silence alarm for two minutes; remove
obstruction and restart pump.
Error Detected Pump fault occurred. Close tubing clamp,
remove pump from service.
Air In Line
Detected
Air in fluid path. Press NEXT to silence
alarm. Make sure tubing is threaded in Air
Detector properly. If fluid path contains
air, close clamps, disconnect from patient
and prime fluid path.
NOTE: When the pump is powered up in
LLO, the Air Detector will automatically
be turned on. If Air Detector is not
required, turn it off in the Options
Menu if you do not want to use it.
3 Beeps Every
5 Minutes;
Stopped on
Main Screen
Pump is stopped. Start pump
if appropriate.
Dose
scheduled
to start in -
Minutes / Start
the Pump
Pump is stopped, but a dose is scheduled
to be delivered in the number of minutes
indicated. In order for the dose to be
delivered, you must start the pump.
Dose scheduled
to start is now
overdue / Start
the Pump
Pump is stopped, but a dose is overdue
for its scheduled delivery. In order for the
dose to be delivered, you must start the
pump.
Dose Duration
is being
lengthened
You have entered a new volume that would
exceed the maximum rate of 350 ml/hr. The
pump automatically lengthened the dose
duration to accommodate the volume you
entered, but confirmation
or a new duration is required.
Dose Cycle
is being
lengthened
The dose duration you have entered
exceeds the dose cycle that is currently
programmed. The pump automatically
lengthened the dose cycle, but
confirmation or a new cycle is required.
PRODUCT(S) DESCRIBED MAY NOT BE LICENSED OR AVAILABLE FOR SALE IN
CANADA AND OTHER COUNTRIES
Smiths Medical ASD, Inc.
St. Paul, MN 55112, USA
Phone: [phone]
Toll-Free USA 1-800-258-5361
www.smiths-medical.com

Find your local contact information at
www.smiths-medical.com/customer-support
Smiths Medical is part of the global technology business smiths group plc.
CADD, CADD-Prizm, Medication Cassette Reservoir Design and the Smiths
Medical design mark are trademarks of Smiths Medical. The symbol ® indicates
the trademark is registered in the U.S. Patent and Trademark Office and certain
other countries. Product referenced is CE-marked.
©2017 Smiths Medical. All rights reserved. IN19811EN-052017
MPAUCA-1576
Recordkeeping Functions
The pump may be running or stopped to view functions or to
print.
To View
Event Log
1. Press OPTIONS.
2. Press ´or Îuntil Event Log option
appears.
3. Press ENTER to display Event Log.
4. Press Îto page back through Event Log
entries or ´to page forward.
5. When finished, press NEXT.
To Clear
Milliliters
Given
Pump must be in LL0 or LL1.
1. Stop the pump.
2. Press NEXT repeatedly until Milliliters
Given screen appears.
3. Press ENTER to clear and update
date and time.
To Print
Reports
• Rx Settings
• Event Log
1. Turn printer on.
2. Connect printer cable to data in/out jack
and to back of printer.
3. If necessary, press ´until Printing
appears.
4. Press ENTER.
5. Press ´or Îto select desired report.
6. Press ENTER.
7. When report is finished, detach printer
cable from pump.
PRODUCT(S) DESCRIBED MAY NOT BE LICENSED OR AVAILABLE FOR SALE IN
CANADA AND OTHER COUNTRIES
Smiths Medical ASD, Inc.
St. Paul, MN 55112, USA
Phone: [phone]
Toll-Free USA 1-800-258-5361
www.smiths-medical.com