SOMFY Freeroll RTS OSE User manual

EN
Installation manual
NL
Installatiehandboek
EL
Εγχειρίδιο εγκατάστασης
5071805A
Freeroll RTS OSE
for rolling garage doors

1
CONTENTS
GENERAL INFORMATION 2
Presentation of the symbols used in this manual 2
SAFETY 2
General information 2
Safety instructions 2
PRODUCT DESCRIPTION 3
Area of application 3
Composition of the kit 3
Control unit description 4
PRE-INSTALLATION CHECKS 5
Preliminary checks 5
INSTALLING THE FREEROLL RTS 5
WIRING FROM THE FREEROLL RTS TO THE MOTOR 6
SETTING THE MOTOR END LIMITS 7
INSTALLING THE RADIO SAFETY EDGE 9
COMMISSIONING OF VERSION WITHOUT MAGNET 14
OBSTACLE DETECTION TEST 14
OPERATION OF THE FREEROLL RTS 15
Operating indicators 15
Using the remote controls 15
Integrated lighting 15
Obstacle detection 15
CONNECTING ADDITIONAL DEVICES 16
General wiring diagram 16
230V-15Washingorangelight  16
12 V electric eye 16
Wired control 17
Alarm buzzer 17
PARAMETER SETTING 19
Adding a remote control 19
Clearing the remote controls 19
Setting the operating modes 20
DIAGNOSTIC AND REPAIRS 21
Receiver, motor and accessories 21
Safety edge transmitter 23
INSTALLATION WITH MAGNETS 24
CLEARING AND PROGRAMMING A TRANSMITTER 26
SAFETY EDGE IN THE RECEIVER
RESETTING THE RECEIVER TO FACTORY SETTINGS 29
CHANGING THE BATTERIES 29
EN
Freeroll OSE RTS

2
GENERAL INFORMATION
SAFETY
This product, installed in accordance with this guide, complies with the EN 13241-1 and
EN 12453 standards.
Somfy declares that this product complies with the essential requirements and other relevant
provisions of Directive 1999/5/EC. A Declaration of Conformity is available at www.somfy.com/
ce (FREEROLL RTS). Product can be used in the European Union and Switzerland.
Presentation of the symbols used in this manual
Presses Led status
Short press Greenashing Green continuous
Press until Orangeashing Orange continuous
Redashing Red continuous
General information
Always read this installation guide and safety instructions before installing this Somfy product.
This Somfy product must be installed by a professional motorisation and home automation
installer, for whom this guide is intended.
The use of any safety components not approved by Somfy remains the sole responsibility of
the installer.
This guide describes how to install, commission and operate this product.
Moreover, the installer must comply with current standards and legislation in the country in
which the product is being installed, and inform his customers of the conditions for use and
maintenance for the product.
AnyuseoutsidethesphereofapplicationspeciedbySomfyisforbidden.Thisinvalidatesthe
warranty and discharges Somfy of all liability, as does any failure to comply with the instructions
given herein.
Safety instructions
Beforettingthereceiver,refertothesafetyinstructionsfortheRDOCSImotor.
WithRDOCSImotors,thereceivermustbettedinsidethegarage.
To ensure the control devices are out of the reach of children, position all control buttons a
minimum of 1.5 m above the ground. They must be visible from the garage entrance but away
from moving parts.
...
EN
Freeroll OSE RTS

3
PRODUCT DESCRIPTION
Composition of the kit
No. Description Quantity
1Pre-wired Freeroll receiver 1
2Receiver cover 1
3Integrated enclosure lighting 1
4Cable ties 1
5External Led 1
6External control buttons ribbon 1
7Safety edge transmitter pre-paired in the factory 1
8Remote controls pre-paired in the factory 2
9Aerials 2
10 Hardware bag 1
11 230V E14 bulb 25W max 1
Area of application
Roller garage doors for residential use.
The safety instructions must be followed throughout the installation:
• Takeoffanyjewellery(bracelet,chain,etc.)duringinstallation.
• Fordrillingandweldingoperations,wearspecialglassesandappropriateprotection.
• Usetheappropriatetools.
• Becarefulwhenhandlingthemotorisationsystemtopreventanyriskofinjury.
• Donotconnecttothemainsbeforecompletingtheassemblyprocess.
• Neverusehighwaterpressurecleaningequipment.
Contents may vary according to the kit.
EN
Freeroll OSE RTS

4
No. Component
1Reset push button
2Radio card with programming push button and status led (daughterboard)
3DIP 2 dipswitch
4Radio aerial connector
5Front panel 3 colour led connector
6SEC push button and status led
7Up control push button (used when the cover is open)
8Stop control push button (used when the cover is open)
9Down control push button (used when the cover is open)
10 DIP 1 dipswitch
11 Front panel control button connector (accessible on the cover)
12 6.3 A – 250 V fuse
13 Connection terminal
Control unit description
EN
Freeroll OSE RTS

5
INSTALLING THE FREEROLL RTS
Ensure the wall plug is at
the correct distance. The
Freeroll receiver is pre-
wired with a 2.50 m cable.
It is recommended that the
Freeroll receiver is fitted on
the same side of the door as
the safety edge transmitter.
[1].Remove the cover for the integrated lighting by pressing the base
on either side. Remove the front panel from the receiver.
PRE-INSTALLATION CHECKS
Preliminary checks
TheFreerollmustnotbettedinanareapronetowatersplashes.
ThebottomofthedoormustbettedwithasafetyedgecompatiblewiththeFreerollsystem.
Ifthegaragedooristheonlyaccesstothegarage,tanexternalbackreleaseinordertouse
the handle for the RDO CSI motor emergency system.
Ifthegaragedoorfacesapublicroad,tanorangelightsignaldevice(partnumber9015034,
see page 16).
Check there are no dangerous parts accessible on the door. If this is the case, protect them.
solsolsol
Récepteur
Freeroll
Emetteur
barre palpeuse
Freeroll
receiver
Safety edge
transmitter
Floor
EN
Freeroll OSE RTS

6
[3]. Hold the receiver against the wall (lighting facing upwards) and
line up with drilled holes. Use the supplied hardware or hardware
thatisbettersuitedtothematerialsandxthereceivertothe
wall.
WIRING FROM THE FREEROLL RTS TO THE MOTOR
The Freeroll receiver must not be connected to the mains when connecting to
the motor.
Ensure the direction of the connections respect the direction of assembly of
the motor and door as indicated below.
[1].Position yourself facing the garage door, on the head
rail side.
[2].Locate the position of the motor head: to the left or right.
[3].Connect the motor wires to the Freeroll receiver in
accordance with the following table.
[4].Connect the Freeroll receiver to the mains.
•The receiver beeps once.
•Theexternalledashes,thengoesCONTINUOUSLYGREEN.
Motor head on left-
hand side
Motor head on right-
hand side
Blue T7 T7
Black T9 T8
Brown T8 T9
[2].Screw the two aerials to the Freeroll receiver (see mark 4).
Ensure the two aerials do not touch or cross over each other
and that they are pointing in opposite directions (one upwards,
one downwards and both of them are parallel to the side of the
product).
Avec
alarme
Sans
alarme
With
alarm
Without
alarm
EN
Freeroll OSE RTS

7
[1].On DIP 1 of the receiver: switch dipswitches 1, 2 and 3 to ON
and dipswitch 4 to OFF (motor end limit setting mode + radio
deactivated).
Normal
mode
Note: The motor end limits can also be set with a setting tool (ref. 9686027). In this case, do
not follow steps 1 to 4 above.
Motor end
limit setting
mode
[2].Test the direction of rotation of the motor using the
control buttons inside the receiver (marks 7, 8, 9).
If necessary, invert the terminals of wires T8 and T9. See page 6.
Before inverting the direction of rotation of the motor,
ensure the Freeroll receiver is disconnected from the
mains.
[3].Set the motor end limits using the buttons inside the Freeroll
receiver (refer to the motor's manual for setting the end limits).
[4].Return all the DIP 1 dipswitches on the receiver to OFF (normal
mode).
SETTING THE MOTOR END LIMITS
When setting the motor end limits, the safety edge transmitter must not be fixed
to the door.
EN
Freeroll OSE RTS

8
►Closing the Freeroll receiver
[1].Connect the external control button ribbon carefully to the circuit
board terminal (mark 11).
Ensure the button ribbon's direction of connection
is respected to prevent the external controls from
malfunctioning.
[2].Connect the LED to the circuit board (mark 5).
OK
NO
[3].Rehouse the LED in the receiver cover.
[4].Retthereceivercover.
[5].Retthereceiver'sintegratedlightingcover.
EN
Freeroll OSE RTS

9
INSTALLING THE RADIO SAFETY EDGE
- The safety edge transmitter must always
be installed inside the garage on the right-
hand side of the end slat.
- If possible, position the receiver on the
same side as the safety edge transmitter
(right-hand side).
solsolsol
STOP
►Fitting the safety edge
[1].If the safety edge was pre-tted in the factory, go
directly to page 14.
[2].Place the door in the intermediate position by
pressing and holding button or .
Note: if the external control buttons do not work, ensure
the ribbon has been correctly connected (see
page 8).
[3].Select the type of assembly (2 options):
- Assembly A: wiring in the end slat.
Rear access to the safety edge transmitter.
- Assembly B: wiring in the safety edge rubber.
External access to the safety edge transmitter.
[4].Pre-drill the end slat according to the desired
assembly selection.
The lip of the safety edge rubber must be fitted
on the outside of the door.
Assembly A Assembly B
External lip
on right-
hand
side
Floor
EN
Freeroll OSE RTS

10
[5]. Prepare and position the rubber:
- Select the rubber compatible with the end slat of the
door. Several rubbers are available :
 Partno.9015220-OSERubberProle143600
 Partno.9016662-OSERubberProle143604
 Partno.9015221-OSERubberProle204001. 
Ifnoneoftheserubbersiscompatible,tanadapterrail
Ref. 9017241 for rubber ref 9015220 only
•Assembly A: 3 holes
Pre-drill 3 holes on the right-hand
end of the end slat, inside:
- 2 holes of 2 mm diameter for
securing the transmitter,
- 1 hole of 12 mm diameter for
feeding the electric eye cables.
•Assembly B: 2 holes
Pre-drill 2 holes 2 mm in diameter
for securing the transmitter to the
right-hand end of the end slat,
inside.
- Cut the rubber according
to the dimensions
opposite,
- Slide the safety edge
rubber into the end slat.
25 mm 25 mm
Runner Runner
Zone
reserved
for stop
Zone
reserved
for stop
End slat of the door
Rubber
Length of end slat
Length of rubber = Length of end slat - 50 mm
Lèvre
côté
extérieur
The lip of the safety edge
rubber must be fitted on
the outside of the door.
External lip
EN
Freeroll OSE RTS

11
[8].Secure the safety edge transmitter
on the lowest slat.
[6].Fit the electric eyes in the
rubber.
Position yourself inside
the door and install the
electric eye with the
shortest wire (black) on
the right-hand side of the
end slat.
End slat of
the door
Grey transmitter
cable on left-hand
side
Black transmitter
wire on right-hand
side
Rubber
[7].Feed the electric eye cables.
Recommended: Use an electrician's pointer to make it easier to feed the electric eye
cables.
Assembly A Assembly B
22 mm
22 mm
Drill 2 holes of 6 mm diameter
Slat seen
from below
Feed the cables into the 3 holes
of the end slat
Drill the rubber and feed the
cables through the rubber
[9].Remove the protective lm from
the battery in the safety edge.
The LED 1 and LED 2 indicator lights
ash GREEN once then ORANGE
for between 5 and 30 seconds, then
GREEN again for 5 seconds.
Note: IftheLED1and2indicatorlightsash
ORANGE for longer than 1 to 2 minutes, the
battery must be replaced.
Pile
Battery
EN
Freeroll OSE RTS

12
This operation is compulsory - if the 2
stops are not installed, there is a risk
that the door will detect an obstacle
and reopen each time it is closed.
[11]. Fit the 2 stops to the 2 ends of the
lowest slat in order to avoid crushing
the rubber and the electric eyes
when closed.
Left-hand
stop
Right-
hand stop
[10]. Connect the electric eyes to the
safety edge transmitter.
J1 J2
Red = Rouge Blue =Bleu
Black = Noir Black = Noir
Brown = Marron
20 mm
maxi
Use the wiring tool to connect
the wires as shown opposite.
It is recommended that a maximum
of 20 mm of sheath is removed. Do
not strip the wires.
Press firmly on the wiring tool up
to the stop to guarantee a good
electrical contact.
Do not strip
the wires
Note: A wiring socket, ref 9015561, which
can be adapted for a screwdriver, is
available on request for more intensive
use.
+
ref 9015561
20 mm
maximum
EN
Freeroll OSE RTS

13
[12]. Start auto-programming of the
rubber length by the safety edge
transmitter:
- Press push button SW2 until the
LED 1 indicator light comes on
continuously.
- Auto-programming has been
successful if the LED 1 indicator
light ashes GREEN then the
LED 2 indicator light comes
on CONTINUOUS GREEN for
approximately 8 seconds.
Note: The safety edge can be
tested by compressing the rubber
during this 8-second period. The
LED 2 indicator light changes from
greentoredtoconrmdetection.
- Auto-programming has failed if
the LED 1 indicator light
ashes RED then the LED
2 indicator light remains off.
In this case, restart
auto-programming.
If the problem persists,
move switch SW1 to position
1 and press SW2 again.
Move switch SW1 incrementally
until the LED 1 and LED 2 indicator
lights come on CONTINUOUS
GREEN.
battery
Pile
[14]. Close the safety edge transmitter
again.
- Ensure that the seal is correctly
positioned.
- Put the cover on the box.
- Tighten the 3 screws.
Do not use an electric screwdriver.
3 vis
[13]. Congure the safety edge
transmitter according to the type of
door and motor:
Motor speed End slat
height
SW3
dipswitch 3
position
17 rpm 77 mm OFF
12 rpm 77 mm ON
17 or 12 rpm 55 mm ON
Pile
1234
ON
1234
ON
Battery
Battery
Battery
3 screws
EN
Freeroll OSE RTS

14
COMMISSIONING OF VERSION WITHOUT MAGNET
[1].Connect the Freeroll receiver
[2].Using the tip of a pen, press the SW4 PROG push button
on the safety edge transmitter until the LED 2 indicator
light goes out. The LED 2 indicator light will come on green
for a moment.
[3].Make a movement command (up or down) to conrm
that there is a good radio connection between the
transmitter and the receiver. When the door starts up, the
LED 2 indicator light on the transmitter should come on
continuous green.
Commissioning is complete.
Note:Ifcommissioningprovesdifcult,orifthereareproblems
with waking up the transmitter when the door starts up or
if an obstacle is detected on the ground, see page 24.
Note:Forinstallationrenovations,seepage26totanew
transmitter.
OBSTACLE DETECTION TEST
Test obstacle detection by simulating the presence of an obstacle when closing.
The door should stop and go up.
Thereceiverledwillashorangetoindicatetheactivationofthesafetyedge.
If the obstacle detection test fails, see page 21.
ATTHISPOINTINTHEINSTALLATION,THEFREEROLLRECEIVERISREADYTOOPERATE.
4 s
EN
Freeroll OSE RTS

15
Obstacle detection
During opening, the detection of an additional weight will cause the door to stop (anti-lift function).
During closing, the detection of an obstacle causes the door to stop and re-open partially.
Operating indicators
The receiver external led gives the operating indications for the door.
Each time the opening command is given, the receiver will emit a beep.
Receiver LED (mark 5) Door status
Green continuous Upper end limit reached
Greenashing Door opening
Red continuous Lower end limit reached
Redashing Door closing
Orange continuous Door stopped between upper and lower end
limits
Integrated lighting
The lamp comes on each time a command is sent to the receiver.
It goes out 2 minutes after the door stops.
OPERATION OF THE FREEROLL RTS
Using the remote controls
The remote controls supplied in the kit are pre-programmed in the factory to the left-hand
button.
They can be used directly to control the garage roller door.
Successive presses on the same control button will lead to the following operations of the door:
Open, Stop, Close, Stop, Open etc.
Note: With a "3 button" Telis type remote control, successive presses of the centre button
(My/STOP) will lead to the following operations of the door: Open, Stop, Close, Stop, Open etc.
STOP
STOP
If the commands are made too quickly one after another, the receiver will not
have enough time to process them and they will not all be carried out.
5
EN
Freeroll OSE RTS

16
230V-15Washingorangelight--------- Ref. 9015034
►Connection
Connect the orange light in parallel to the integrated lighting of the
Freeroll receiver.
►Operation
The orange light ashes each time the receiver is controlled,
giving a 2 second warning.
Itstopsashing2minutesafterthedoorstops.
12 V electric eye ---------------------- Ref. 9013647
General wiring diagram
Terminals T17 - T18 and T11 - T12 must be bridged if they are not used.
It is possible to connect an emergency stop device to terminals T11 and T12.
CONNECTING ADDITIONAL DEVICES
C
220-240 VAC
50Hz
230 VAC - 25W
M
NL
{
Black
Red
►RemovethejumperbetweenterminalsT17
and T18 on the Freeroll receiver.
►Connect the 12 Vdc electric eye:
2 possible options with or without Autotest.
EN
Freeroll OSE RTS

17
►Without auto-test
Requires checking for correct operation every 6 months.
On the electric eye:
Switch dipswitch 1 to ON and dipswitch 2 to ON.
►With auto-test
An automatic test is carried out each time a command is sent
to check the correct operation of the electric eye. If the electric
eye is not operating correctly, the door will not respond to the
commands.
On the Freeroll receiver:
Switch the DIP 1 dipswitch 1 to ON (mark 10) to activate
auto-testing of the electric eye then press RESET (mark 1).
On the electric eye:
Bridge terminals 2 and 4. Switch dipswitch 1 to ON and
dipswitch 2 to OFF.
Wired control------------------------------------
►Double throw Up/Down switch Ref. 1841028 or 1841036
Successive presses of Up leads to
the Up, Stop, Up, Stop cycle...
Successive presses of Down leads to
the Down, Stop, Down, Stop cycle...
►Single throw push button
Successive presses of the button leads to
the Up, Stop, Down, Stop, Up, Stop etc. cycle...
12
ON
12
ON
EN
Freeroll OSE RTS

18
►Operation
The alarm is triggered for 5 minutes if the door
is raised manually. No movement of the door is
possible when the alarm is sounding.
►Alarm connection
Connect the alarm to the receiver: connect the
red wire to terminal T10 and the black wire to
terminal T16 of the receiver.
If an electric eye is also connected to the receiver,
it must be wired in "no auto-test" mode.
►Alarm activation
Place the door in the upper position.
Press the SEC button (mark 6)
until the led (above the SEC button)
stays on. Release the button, the receiver beeps
once.
The alarm buzzer is activated.
►Testing the alarm
Simulate a forced entry by opening the door
using the crank (CSI function) and lift the end
slat manually by pressing on the rubber. Press
a button on a remote control memorised in the
receiver to stop the alarm.
►Stopping the alarm
When the alarm sounds, press a button on a
remote control memorised in the receiver to
stop it. The alarm can only be stopped with a
memorised remote control.
Note: If the alarm is not connected and there is an
intruder, the door is secured but the alarm does
not sound.
►Deactivating the alarm
Disconnect the alarm. Clear and re-memorise
the safety edge transmitter in the receiver (see
pages 26 to 28).
Black
Red
Alarm buzzer ------------------------- Ref. 9014397
A base magnet must be tted on the door runner (see page 24 for how to t the
magnet and page 25 for how to congure the safety edge transmitter).
EN
Freeroll OSE RTS