SOMFY inteo EOLIS RTS User manual

Installation Instructions
Power supply :
Rated Current :
Operating temperature : -4
24V AC/DC
25 mA at 24V DC
The must be supplied by a class 2 transformerEOLIS RTS
0
sensor
F to +122 F/-20 C to +50 C
00 0
24V EOLIS RTS SENSOR KIT
CAT NO. 6301050
(Includes transformer, not shown)
The is a radio wind sensor for awnings
The wind threshold can be set directly on the
The is compatible with the and motors only.
EOLIS RTS
EOLIS RTS .
RTS LT RTS CMO ALTUS RTS
sensor
sensor
EOLIS sensor
Installation
1Dimensions
9.3 in./236 mm
6.3 in./160 mm
x
x
x
x
x
x
SOMFY SYSTEMS, INC. reserves the
right to update, change or modify
these instructions without prior notice.
REF. NO: 182450A
COPYRIGHT C SOMFY SYSTEMS, INC. 4/02
SOMFY SYSTEMS, INC.
47 Commerce Drive
Cranbury, NJ 08512
SOMFY CANADA
6315 Shawson Drive, Unit #1
Mississauga, Ontario L5T1J2
SOMFY MEXICO S.A. De C.V.
Calle 3 No. 47, Loc. E-5
Fracc Ind. Alce Blanco
Nau., Edo. de Mex C.P. 53370
inteo EOLIS RTS 24Vsensor
Wiring
2
1. Remove Cover and unscrew
plate over wiring compartment
UP
STOP
DOWN
2. Loosen the strain relief
plate and guide the power
supply wires through
the black grommet into
terminal block
3. Connect the cable leads to the terminals
- Terminal block is removable for
easier connections and the input power
is not polarized.
WARNING: For the to function properly, the
transmitter which is memorized into the motor's receiver, must be
configured correctly. The DOWN button MUST correspond to
DOWN on the end product. In the case of an awning, it will open
or extend the awning. If the UP button extends the awning, the
wind sensor will also extend the awning during windy conditions.
THIS IS DANGEROUS! Damage and injury could occur. Do not
proceed until proper operation of the transmitter is verified.
Please refer to the installation instructions of the relevant motor
to change the direction if necessary.
EOLIS RTS SENSOR
grommets
strain
relief
TO 24V AC/DC
TRANSFORMER
TO 24V AC/DC
TRANSFORMER
x
x
4. Replace wire
compartment cover 5. Attach the sensor to the wall.
Replace front cover and secure
with screws provided
A. Power input to the sensor is not polarized,
but turn off the power and fully discharge
the transformer before making final connections.
B. The cable distance between the power supply
and the sensor must not exceed 164 feet.

WIND Function
DEMO Mode TIME DELAYS
The is able to control and provide a measure of protection
for retractable awnings according to wind conditions.
The WIND threshold can be adjusted by a potentiometer to detect wind speed
between6-31miles per hour.
EOLIS RTS sensor
When the wind
speed exceeds
the threshold
set by the
EOLIS RTS
,anUP
order is given
to the awning after 2 seconds
sensor
The mode is selected by turning the wind
potentiometer clockwise to the limit.
The change of setting "In" or "Out" of the Demo Mode
is confirmed with a brief Jog of the motor. This function
can be used to confirm the sensor is communicating
with the motor's receiver.
In this mode all time delays are reduced to
facilitate installation. The wind threshold is 6 mph.
This is the elapsed time required for the motor to respond
automatically or manually (using the transmitter) to the
change in wind conditions.
WIND appearing timing
WIND disappearing timing*
Normal mode
2 sec.
12 min.
Demo mode
2 sec.
15 sec.
As long as the
measured
wind speed is
higher than the
adjusted threshold, all commands
are prevented from operating.
(manual control or automatic control).
When the wind
speed falls
below the
threshold setting,
an order can be
given with the RTS
transmitter after 30 sec.
-Demo
after
30 sec.
after 2 sec.
+
A. To Enter the "programming mode" C. To delete all the sensors and record a new one
The motor must be in to record an
Up to three can be memorized in
one motor. One be memorized into
several motors.
programming mode
EOLIS RTS
EOLIS RTS
EOLIS RTS
sensor.
sensors
sensor nca
Activate the receiver's memory
by pushing (for more than 2
seconds) the
on a transmitter already
recorded in the motor's memory.
programming
button
The awning jogs briefly
DOWN/UP. This confirms
the motor is in
programming mode.
Press on the
"programming"
button of the
EOLIS RTS
briefly
sensor
Press for
on the "prog"
button of the new
EOLIS RTS .
more than
7 sec.
sensor
The awning jogs briefly (DOWN/UP).
If it is a new sensor :
If the sensor was previously recorded :
it will be
in the motor.
it will be
recorded
deleted.
The awning jogs briefly (DOWN/UP).
The receiver is cleared (all previous
sensors are erased) and the new
sensor is recorded.
-+
B. To Record or delete a sensor
-+
-+
> 2 sec.
Operation
4
Programming
3
-Demo
+
NOTE: Do not leave RTS sensor in demo mode when
installation is completed.
* It is possible after 30 sec. to give a
down order with the RTS transmitter