SOMFY Sonesse 30 RS485 User manual

www.somfy.com
Sonesse®30 RS485
Ref :5057808B
DIGITAL TECHNOLOGY SOMFY

1Copyright © 2010 Somfy SAS. All rights reserved - V1 - 01/2011
Installation instructions page 2
SOMFY hereby declares that this product complies with the essential requirements and other relevant provisions of
Directive 1999/5/EC. A Declaration of Conformity is available at the web address www.somfy.com/CE. Suitable for
use in EU, CH and NO
EN
Notice d’installation page 10
Par la présente, Somfy déclare que l’appareil est conforme aux exigences essentielles et aux autres dispositions
pertinentes de la directive 1999/5/CE. Une déclaration de conformité est mise à disposition à l’adresse internet www.
somfy.com/ce. Utilisable en UE CH et NO.
FR
Guía de instalación página 18
Por la presente, Somfy declara que el aparato cumple las exigencias esenciales y el resto de disposiciones pertinen-
tes de la directiva 1999/5/CE. Podrá encontrar una declaración de conformidad en la página web www.somfy.com/ce.
Aplicable para la UE, Suiza y Noruega.
ES
Gebrauchsanleitung Seite 26
Hiermit erklärt SOMFY, dass sich dieses Produkt in Übereinstimmung mit den grundlegenden Anforderungen und

Internetadresse www.somfy.com/ce verfügbar.
Verwendbar in der EU, der Schweiz und Norwegen.
DE
Guia de instalação página 34
Pelo presente documento, a Somfy declara que o aparelho está conforme às exigências fundamentais e às outras
disposições pertinentes da directiva 1999/5/CE. Encontra-se disponível, no sítio web www.somfy.com/ce, uma decla-
ração de conformidade.
Utilizável na UE, Suíça e Noruega.
PT
ZH 42
 
1999/5/EC
www.somfy.com/CE
AR

2Copyright © 2011 Somfy SAS. All rights reserved - V1 - 01/2011
SAFETY

these instructions are intended.



being installed, and inform his customers of the operating and maintenance conditions for the product.

with the instructions given herein will invalidate the warranty, and Somfy refuses to accept liability.
COMPATIBLE BLINDS & CONTROLS
Roller blinds
-
ted behavior. Use of one controller at a time is recommended.
GENERAL SAFETY INSTRUCTIONS
Never immerse the
motor in liquid!
Never drill holes in the
motor!
Avoid impacts!
Do not drop it!
ST OP
Setting Tool Centralis IB Wall Switch
Dry Contact ControlsRS485 Controls
PROG

3Copyright © 2010 Somfy SAS. All rights reserved - V1 - 01/2011
INSTALLATION
Remove Network ID
labels before installing
the crown.
Motor preparation
1) Fit the crown (a) and drive wheel (b)
to the motor.
2) Measure the length (L) between
the middle of the drive wheel and the
head end.
Tube preparation
Cut the tube to the required length.
Deburr the tube and remove the
debris.
Motor/tube assembly
1) Slide the motor into the tube.
2) Fix the tube to the motor with self-
tapping screws or steel pop rivets
depending on the dimension (L).
Mounting the motorized tube on the
brackets
If necessary, screw the bracket inter-
face on the motor head.
Mount the motorized tube on the end
bracket (C ).
Mount the motorized tube on the
motor bracket (D).
L
1
2
ab
1
2
c
d

4Copyright © 2011 Somfy SAS. All rights reserved - V1 - 01/2011
Wiring
1) Connect the power cable to the



3) If you want to use the Dry
contact features of the motor,
connect the Dry contact cable

cable).
Do not apply any
voltage to Dry Contact
connector.

a) Setting Tool or 4 wires switch
1 UP (White/Blue)

3 DOWN (White/Orange)

b) Centralis IB
1 UP or DOWN (White/Blue or White/
Orange)
2 UP or DOWN (White/Blue or White/
Orange)
3 GND (Orange)
c) Wall Switch
1 UP or DOWN (White/Blue or White/
Orange)
2 UP or DOWN (White/Blue or White/
Orange)
3 GND (Orange)
5) Correspondence
1
2
3
4
1
3
4
2
1
2
3
1
2
3
2
3
ST OP
ST OP
ST OP

5
a
b
c
1

5Copyright © 2010 Somfy SAS. All rights reserved - V1 - 01/2011
COMMISSIONING
1) RS485 :
See page 58
2) DRY CONTACT
Checking the direction of rotation
Press the setting tool UP button:
a) If the shade is raised, the direction
of rotation is correct. Move to the sec-
tion entitled «Adjusting the end limits».
b) If the shade is lowered, the direction
of rotation is incorrect. Move to the
next step.

until the shade jogs: the direction of

Press the setting tool UP button to
check the direction of rotation.
Adjusting the end limits

1) Press and hold the UP button to
move the shade to the desired up
position.

DOWN buttons and release them once
the shade begins to move.


reaches the desired down position.
If necessary adjust the down position,
using the UP or DOWN buttons.

UP buttons and release them when
the shade begins to move.


its upper limit.


jogs.

a
b
12
3
5

6Copyright © 2011 Somfy SAS. All rights reserved - V1 - 01/2011
USE
MY position
1) Recording MY position

shade to the desired position with the
UP and DOWN buttons then press

once.
2) Changing the MY position

new desired MY position with the UP
and DOWN buttons then press the

once.
3) Delete the MY position


until the shade jogs once.
1
2
3

7Copyright © 2010 Somfy SAS. All rights reserved - V1 - 01/2011
With the setting tool, it is possible
to cancel and exit the speed or limit
adjustment mode by simultaneously


cancelled with inactivity of 2 minutes.
Adjusting the rolling speed

until the shade jogs twice.
-
matically in 10 second cycles.

press the UP button to increase the
speed or DOWN button to decrease
the speed.


shade jogs.
UP, DOWN and MY


DOWN button.

button.
-

x2
10s 10s
1
2
3
1
2
3

8Copyright © 2011 Somfy SAS. All rights reserved - V1 - 01/2011
End limit re-adjustement

1) Press the UP button, to move the
shade to the limit to be readjusted.
2) Press and hold the DOWN and

shade jogs.
3) Press and hold the UP or DOWN
button to move the shade to the new
desired position.


jogs.

1) Press the DOWN button, to move
the shade to the limit to be readjusted.

buttons simultaneously until the shade
jogs.
3) Press and hold the UP or DOWN
button to move the shade to the new
desired position.


jogs.
Modifying the direction of rotation

and hold all the three buttons simulta-
neously until the shade jogs twice.
Erasing the memory of the motor.
Press and hold all the three buttons
simultaneously until the shade jogs 3
times.
All the settings are erased.
1
2
3

1
2
3

x2
x3