Sony MRW-EA7 User manual

MRW-EA7 4-209-215-01(1)
Overview
The MRW-EA7 (hereafter referred to as the “reader/writer”) has
the following features:
sQuick and simple data transfer - easily transfer images from
camera and mobile phone to PC.
sCompatible with “Memory Stick”, “Memory Stick Duo”,
“Memory Stick Micro” (“M2”), CompactFlash, Microdrive,
xD-Picture Card, MultiMediaCard, SD Memory Card,
microSD Card.
sMultiple card formats supported
sDrive Letter Recognition Software can be downloaded from
the web site
sQuick to Connect - Hot-pluggable USB-powered design
System Requirements
The reader/writer requires computers with the following
preinstalled operating systems.
•OS
– Windows®7
–Windows Vista® (Service Pack 2 or later)
– Windows®XP
– Windows®2000 Professional (Service Pack 4 or later)
–Mac OS X 10.2, 10.3, 10.4, 10.5, 10.6
This product works with the standard drivers in Windows.
Supported Media
The reader/writer supports the following media:
“Memory Stick” media
•“Memory Stick” (without MagicGate) *1
•“MagicGate Memory Stick” *1*2
•“Memory Stick” (with MagicGate) *1*2*3
•“Memory Stick Duo” (without MagicGate) *1
•“MagicGate Memory Stick Duo” *1*2
•“Memory Stick Duo” (with MagicGate) *1*2*3
•“Memory Stick PRO” *2*3
•“Memory Stick PRO Duo” *2*3
•“Memory Stick PRO-HG Duo” *2*3
•“Memory Stick Micro” (“M2”) *2*3*4
*1 “MagicGate” is the general name of a copyright protection technology
developed by Sony.
*2 Recording or playback of MagicGate data that uses MagicGate
technology is not supported.
*3 4-bit parallel data transfer is supported and the data read/write timing
will vary depending on the medium.
*4 “M2” is an abbreviation of “Memory Stick Micro.” In this document,
hereinafter, the abbreviation “M2,” is used.
SD memory cards
•SD Memory Card *5
•SDHC™ Memory Card *5
•miniSD™ Card *5*6
•miniSDHC™ Card *5*6
•microSD™ Card *5
•microSDHC™ Card *5
*5 Recording or playback of data that uses copyright protection
technology is not supported
*6 With adaptor (not supplied) only
Other memory cards
• MultiMediaCard *7
• RS-MMC *7
•CompactFlash®
• Microdrive®*8
•xD-Picture Card™
*7 MMCplus and MMCmobile are supported, but parallel data transfer is
not supported.
*8 The Microdrive requires more power than other memory cards. When
using a Microdrive, remove other memory cards; otherwise an error
may occur due to a shortage of power.
Notes
•Not all memory cards are guaranteed to work. Operation is
not assured if non-supported memory cards are used.
•The capacity of a file to be recorded/played back is smaller
than 4 GB per file according to the specifications of the file
system incorporated in “Memory Stick.”
•Although operation check of this product has been performed
with up to 8 GB “Memory Stick,” please note that the
operation is not guaranteed for every type of “Memory Stick.”
•In this manual, all types of media listed in “Supported Media”
are generically called memory cards.
•I/O cards that are not memory cards, such as GPS cards, are
not supported.
•MultiMediaCards and SD Memory Cards use the same slot, so
you cannot use them at the same time.
• The “Memory Stick” media all use the same slot, so you
cannot use them at the same time.
•The “Memory Stick Micro” (“M2”), microSD Card, and
microSDHC Card all use the same slot, so you cannot use
them at the same time.
•Only DOS format is supported. Memory cards in other
formats are not supported.
About “Memory Stick” media
What is “Memory Stick”?
“Memory Stick” is a compact-size IC recording media with a
high capacity. It has been designed not only exchanging/sharing
digital data among “Memory Stick” compliant products, but
also for serving as a removable external storage media that can
save data.
Notes on “Memory Stick”
On formatting (initialization)
•If you format media in which data has been already written,
all the data will be erased. Please be cautious not to
mistakenly erase any important data.
•Please make sure to format (initialize) media by the formatter
of a “Memory Stick” compliant product. If it is initialized by
Windows Explorer, it might become unusable on this
product.
About the size of “Memory Stick”
•This product has a slot that can take both standard size and
Duo size. All the products with such a slot as this are
equipped with a system which automatically measures the
size of an inserted media. That’s why both standard-size
“Memory Stick” media and smaller “Memory Stick Duo”
media can be used on this product without any Memory Stick
Duo Adaptor.
•Do not insert two or more pieces of media at the same time. It
might cause damage to the product.
•When you use “Memory Stick Duo” media and “Memory
Stick Micro” media on this product, please make sure to insert
it in the right direction.
•“Memory Stick Duo” media and “Memory Stick Micro”
media should be kept away from small children to prevent
them from accidentally swallowing it.
Usage Notes
“Memory Stick” Media
Notes on using “Memory Stick” media
•Do not remove “Memory Stick” media while data is being
read or written.
•Data may be damaged if:
–You remove “Memory Stick” media or disconnect the USB
cable while data is being read or written.
–You use “Memory Stick” media in a place where it is
susceptible to static electricity or electric noise.
•We recommend that you make a backup copy of important
data in “Memory Stick” media.
•Do not touch the terminal of “Memory Stick” media with
anything including your fingers or metalic objects.
•Do not bent, drop or put a big impact on “Memory Stick”
media.
•Do not disassemble or modify “Memory Stick “ media.
•Keep “Memory Stick” media away from water.
•Do not use or keep “Memory Stick” media under an
unfavorable condition as below:
–Extremely hot place (such as in a parked car with windows
closed in summer, a spot under direct sunlight, or near an
electrical appliance that radiates heat)
–Humid place
–Place near corrosive substances
•If you set Write-Protected switch “LOCK,” data cannot be
recorded, edited, or erased.
• Do not stick anything other than the supplied labels on the
label area of “Memory Stick” media.
•Stick a label precisely within the label area. Make sure that the
label does not go beyond the area.
Notes on using “Memory Stick Duo” media
•When you use “Memory Stick Duo” media without Write-
Protected switch, be careful not to edit or erase important data
by mistake.
•When you use “Memory Stick Duo” media with Write-
Protected switch, data cannot be recorded, edited, or erased
by “LOCK” the switch.
•Use an object with a sharp tip to move the Write-Protected
switch.
•Do not press on the memo area strongly when writing.
Other Points to Note
Media formatting
Do not format (initialize) memory cards with a computer. If you
format a memory card with a computer, devices such as digital
cameras and mobile phone may not be able to use it due to
differences in format type (FAT size, cluster size, hard disk type,
or super floppy disk type). If you use a digital camera, format
memory cards with your camera, instead.
Restrictions on DOS mode
In Windows, the reader/ writer does not operate in DOS mode.
To use the reader/writer, start up Windows.
Standby
The reader/writer supports standby functions based on the
PC2000 standard, which may not cover the standby function of
all computers. Disable the standby function of your computer if
it causes any problems. While the computer is in standby, do not
insert or remove any media.
Do not attempt to dismantle, repair, or alter the
reader/writer yourself
Do not, under any circumstances, attempt to dismantle, repair,
or alter the reader/writer yourself. You may not only
permanently damage the reader/writer and/or your computer,
but may also cause fire or personal injury through electrical
shock.
Operating and storage environments
•Do not place the reader/writer close to heat sources or in
direct sunlight; in dusty, dirty, or humid locations; under
precipitation such as rain; or leave it in a hot vehicle with the
windows closed.
•If the reader/writer interferes with the reception of radio or
television signals, move the reader/writer away from the
radio or television.
•When using the reader/writer, do not wrap it in cloth, sheets,
or covers as this may cause a malfunction or fire.
Specifications
USB transfer rate
Full-speed (Up to 12 Mbps)
High-speed (Up to 480 Mbps)
This high-speed transfer rate is a theoretical value for the USB
standard.
Actual performance is dependent on the device.
Power requirements
4.75 to 5.25 V DC
Current consumption
Max. 500 mA *1
Access indicator
Always lit.
Blinks on access.
Operating environment
Temperature: 5oC to 40oC (41oF to 104oF)
Humidity: 30% to 80% RH
Storage environment
Temperature: -30oC to +60oC (-22oF to +140oF)
Humidity: No condensation
Dimensions (W x H x D)
Approx. 86 ×15.7 ×50 mm
(3 3/8×5/8×2 inches) (excluding protrusions)
Mass
Approx. 57g (2.0 o.z.)
*1 Consumption may be higher when using Microdrive
End User License Agreement
IMPORTANT NOTICE
The following “END USER LICENSE AGREEMENT” applies to
the Drive Letter Recognition Software provided by Sony. Please
read the following “END USER LICENSE AGREEMENT” before
installing. By installing the Drive Letter Recognition Software,
you agree to the “END USER LICENSE AGREEMENT”.
END USER LICENSE AGREEMENT
This is a legal agreement between you
(hereafter referred to as the User) and Sony Corporation
(hereafter referred to as Sony) pertaining to the right to use the
software (hereafter referred to as the PROGRAM). Using the
PROGRAM indicates your acceptance of these terms and
conclusion of the Agreement between the User and Sony.
1 Copyright and all other rights relating to the PROGRAM and
documents accompanying the PROGRAM are owned by Sony
or the original rightful person or organization (hereafter
referred to as the original rightful person) granting Sony the
right to use the PROGRAM. The User is granted no rights
other than those specified in this agreement.
2Sony grants the User the non-exclusive, indivisible and non-
transferable right to use the PROGRAM for the purpose of
using the Sony product Multi-Card Reader/Writer for which
the PROGRAM designates.
3The User may not transfer the Right of Use described above to
any third party nor allow for any third party to use the
PROGRAM unless the User obtains the advance written
permission of Sony.
4The User may not export or transport the PROGRAM or
documents accompanying the PROGRAM from the country
where the User installed the PROGRAM to any other country.
5The User may not (i) update, add to, or modify nor (ii) de-
assemble or de-compile the PROGRAM either in whole or in
part.
6THE PROGRAM IS PROVIDED “AS IS” WITHOUT EXPRESS
OR IMPLIED WARRANTIES, INCLUDING WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE OR NON-DEFECTIVENESS.
7If any dispute relating to infringement of copyright, patent, or
other intangible property rights arises between the User and a
third party as a consequence of use of the PROGRAM, the
User shall settle the dispute at the User’s own expense, and
shall make no claim against Sony or the original rightful
person.
8 Sony may terminate your license upon notice for failure to
comply with any of these Terms. Any such termination shall
not affect any payments, any compensation for damage. Upon
termination, you must immediately destroy the Software
together with all copies in any form.
9This Agreement has several non-English language versions
for the reference purpose only. In the event of any
discrepancy between the English language version and any
other language version, the English language version shall
prevail.
Package Contents
When you unpack the box, make sure that it contains all the
accessories listed below.
If anything is missing or damaged, contact your retailer.
•MRW-EA7 Multi-Card Reader/Writer
•USB cable
•Operating Instructions
Parts and Functions
Front
1Access Indicator
This indicator is always lit. The indicator blinks when the
reader/writer accesses data on a memory card.
2xD-Picture Card Slot
Insert xD-Picture Card here.
3“Memory Stick” Slot
Insert a “Memory Stick” media here.
4CompactFlash / Microdrive Slot
Insert either a CompactFlash or Microdrive memory card
here.
Remove all other memory cards before using a Microdrive,
because of its large power consumption.
5MultiMediaCard / SD Memory Card Slot
Insert either a MultiMeidaCard or an SD Memory Card here.
When inserting a miniSD Card, use an adaptor (not
supplied).
6“Memory Stick Micro” (“M2”) / MicroSD and
microSDHC Card Slot
Insert either a Memory Stick Micro (“M2”) or microSD Card,
and microSDHC Card here.
Rear
7USB Port (mini B)
Connect to a computer using the supplied USB cable.
Connecting the Reader/Writer to
a Computer
Simply connect the reader/writer to a computer using the
supplied USB cable.
1 Start the computer.
2Connect the smaller connector of the USB cable to
the USB port on the rear of the reader/writer.
3Connect the larger connector of the USB cable to
the USB port on the computer.
The computer recognizes the reader/writer as a removable
disk, and the reader/writer is ready for use.
Notes
•Do not connect to the USB port on the computer via an
external USB hub.
•Depending on the computer and the status of its operating
system, the reader/writer may not operate or may become
unstable. If this occurs, refer to the “Troubleshooting” section.
• After disconnecting the USB cable, wait at least 5 seconds
before reconnecting it. (Otherwise, the reader/writer may not
be recognized.)
•When two or more USB devices are connected to one
computer, the reader/writer is not guaranteed to operate
simultaneously with some types of USB device.
•You cannot access two or more memory cards simultaneously
on a single computer by connecting additional memory card
devices. Remove any memory cards from the reader/writer or
turn off the other devices.
Notes for Windows
•On some computers, a message may appear asking you to
insert the operating system disc. When this happens, follow
the computer’s instructions.
• On some computers, the USB Mass Storage will function at
reduced speed message may appear, indicating that a hi-
speed USB device has been connected to a USB which does
not support hi-speed USB. If your computer has multiple USB
ports, try connecting to a different port. Otherwise, close the
message and continue using the reader/writer with the
current port.
WARNING
Keep the unit away from children. If any part of the
unit is swallowed, promptly see a doctor.
To reduce the risk of fire or electric shock, do not
expose this apparatus to rain or moisture.
To avoid electrical shock, do not open the cabinet.
Refer servicing to qualified personnel only.
Caution
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for
help.
You are cautioned that any changes or modifications not
expressly approved in this manual could void your authority to
operate this equipment.
Note
If you have any questions about this product, you may call the
telephone number listed in “Technical Support.” The telephone
number below is not for customer service but only for official
purposes.
Declaration of Conformity
Trade Name: SONY
Model No.: MRW-EA7
Responsible Party: Sony Electronics Inc.
Address: 16530 Via Esprillo, San Diego, CA 92127
U.S.A.
Telephone No.: 858-942-2230
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including
interference that may cause undesired operation.
NOTICE TO USERS
Drive Letter Recognition Software ©2010 Sony Corporation.
Documentation ©2010 Sony Corporation.
All rights reserved. This manual or Drive Letter Recognition
Software described herein, in whole or in part, may not be
reproduced, translated to any machine-readable form without
prior written approval from Sony Corporation.
IN NO EVENT SHALL SONY CORPORATION BE LIABLE
FOR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL
DAMAGES, WHETHER BASED ON TORT, CONTRACT, OR
OTHERWISE, ARISING OUT OF OR IN CONNECTION WITH
THIS MANUAL, THE DEVICE DRIVERS OR OTHER
INFORMATION CONTAINED HEREIN OR THE USE
THEREOF.
Sony Corporation reserves the right to make any modification to
this manual or the information contained herein at any time
without notice.
SONY CORPORATION IS NOT RESPONSIBLE FOR ANY
DAMAGE TO OR LOSS OF ANY PROGRAMS, DATA, OR
OTHER INFORMATION STORED ON ANY MEDIA.
Copyright law prohibits unauthorized use of any recorded
audio/video for any other purpose than personal enjoyment.
Please be warned that the “Memory Stick” containing images
and data protected by copyright shall be strictly used within
copyright law.
Trademarks
•, “Memory Stick,” “Memory Stick Duo,” “MagicGate
Memory Stick,” “Memory Stick PRO,” “Memory Stick PRO
Duo,” “Memory Stick PRO-HG Duo,” “Memory Stick Micro,”
and “M2” are registered trademarks or trademarks of Sony.
• Microsoft®, Windows®, and the Windows logo are trademarks
or registered trademarks of Microsoft Corporation in the
United States of America and/or other countries.
• Macintosh®and Mac OS®are registered trademarks of Apple,
Inc. in the United States of America and/or other countries.
• Other system names, product names, and company names
appearing in this manual are trademarks or registered
trademarks of their respective holders, even though not
indicated by the ® or ™ marks.
4-209-215-01 (1)
Operating Instructions
Before operating the unit, please read this document
thoroughly, and retain it for future reference.
Multi-Card
Reader/Writer
© 2010 Sony Corporation Printed in China
http://www.sony.net/
MRW-EA7
Terminal
Label area
Write-Protected
switch
Terminal
Memo area
Write-Protected
switch

MRW-EA7 4-209-215-01(1)
Using the Reader/Writer
Inserting a Memory Card
Insert a memory card into the corresponding slot on the reader/
writer.
When inserting a card, push it in as far as it can go.
Notes
•Each card slot is designed so a card can only be inserted in the
correct direction.
•Insert only one memory card into the corresponding slot. Do
not insert multiple cards at the same time.
•When inserting a mini SD Card, use an appropriate adaptor
(not supplied).
•Do not insert a card upside down.
•Forcibly inserting the card may damage the card or the slot.
Notes
•If a memory card is inserted incorrectly, you may not be able
to remove it. In the unlikely event that a memory card
becomes stuck in the reader/writer, consult your local Sony
dealer.
Reading and Writing Data on a Memory Card
For Windows
The following explanation is illustrated with screens from
Windows XP.
The screens may differ for other versions of Windows.
1Open [My Computer].
2Make sure the removable disk icons appear in [My
Computer].
Drive letters for the removable disk icons are assigned in
alphabetical order to the CompactFlash / Mircodrive Slot,
xD-Picture Card Slot, MultiMediaCard / SD Memory Card
Slot, “Memory Stick” Slot and “Memory Stick Micro”
(“M2”) media / microSD Card Slot.
For example, if the computer has an A:, C:, and D: drive
before connecting the reader/writer, the drive letters will be
assigned as follows when the reader/writer is connected:
Computer drive name Corresponding memory card
Removable Disk (E:) CompactFlash
MicroDrive
Removable Disk (F:) xD-Picture Card
Removable Disk (G:) MultiMediaCard
SD Memory Card
Removable Disk (H:) “Memory Stick” media
Removable Disk (I:) “Memory Stick Micro” (”M2”) media
mircoSD Card
3Insert a memory card into the corresponding slot.
When a volume label has been assigned to the memory card,
the volume label will be displayed together with the
removable disk icon.
4 Use the removable disk icon to read or write data
on the memory card.
If the following message appears, the memory card has not
been recognized correctly, even though the access indicator
lights up. Remove the card and insert it again.
For Window 7 and Macintosh
1Insert a memory card into the corresponding slot.
The removable disk icon appears on the desktop.
When a volume label is assigned to the memory card, the
volume label will be displayed together with the removable
disk icon.
2 Use the removable disk icon to read or write data
on the memory card.
For Macintosh
For Windows 7
Removing a Memory Card
Notes
•Do not remove a memory card while the access indicator is
blinking. Doing so may cause damage to the data stored on
the memory card.
•Be sure to follow the steps described below.
Sony accepts no responsibility for any damage or loss that
results from removing a memory card without following the
procedure described below.
For Windows
1Make sure the access indicator is not blinking.
2Open [My Computer].
3Right-click the removable disk icon, and select
[Eject].
4Pull the memory card straight out.
For Windows 7
1Click the Start Button.
2Click [Devices and Printers].
3Right click [USB2.0 Card R/W] drive icon.
4Go to [Eject] with selection option.
5Pull the memory card straight out.
For Macintosh
1 Close the files saved on the memory card, and exit
any currently running applications.
2Make sure the access indicator is not blinking.
3Drag the removable disk icon to the [Trash].
Alternatively, select the removable disk icon, access the
[File] menu on the menu bar, and select [Eject “Untitled”]*.
*Depending on the memory card, a different label than “Untitled”
may be shown.
4Pull the memory card straight out.
Notes
•Use the removable disk icon for the memory card you are
using.
•It may take a while for the removable disk icons to appear.
•If the removable disk icons do not appear, follow the steps
under “Disconnecting the Reader/Writer From the
Computer” in the Operating Instructions (this manual) to
disconnect the reader/writer, and then wait at least 5 seconds
before reconnecting it.
If the [Safely Remove Hardware] icon mentioned in step 1 of
“Disconnecting the Reader/Writer From the Computer” is not
displayed, skip the rest of the procedure and immediately
disconnect the reader/writer.
•Depending on your operating system and the type of memory
card you are using, the reader/writer drives may be
recognized as “Local Disks” instead of “Removable Disks,”
but this will not affect their operation.
Insert one of the following
“Memory Stick” media in
this slot:
• “Memory Stick”
(without MagicGate)
• “MagicGate Memory Stick”
• “Memory Stick”
(with MagicGate)
• “Memory Stick Duo” (without
MagicGate)
• “MagicGate Memory Stick Duo”
• “Memory Stick Duo”
(with MagicGate)
• “Memory Stick PRO”
• “Memory Stick PRO Duo”
• “Memory Stick PRO-HG Duo”
Insert one of the following cards in this slot:
•MultiMediaCard
•RS-MMC
•SD/SDHC Memory Card
•mini SD Card*
* Use an appropriate
adapter (not supplied).
Insert one of the following
cards in this slot:
•
CompactFlash
•Microdrive
Insert one of the following
cards in this slot:
•xD-Picture Card
Reading the Access Indicator
The access indicator changes according to the status of the
reader/writer, as follows:
Reader/writer status Access indicator
Connected to a computer Lights up
Reading/writing data Blinks
Note
If data cannot be read from or written to the memory card while
the access indicator is lit, make sure the card is fully inserted
into the slot.
Disconnecting the Reader/Writer
From the Computer
Notes
•Do not disconnect the reader/writer from the computer while
the access indicator is blinking. Doing so may cause damage
to the data stored on the memory card.
•Be sure to follow the steps described below.
Sony accepts no responsibility for any damage or loss that
results from disconnecting the reader/writer without
following the procedure described below.
For Windows
The following explanation is illustrated with screens from
Windows XP, and assumes that drive names E:, F:, G:, H: and I:
are assigned to the four slots of the reader/writer.
The screens may differ for other versions of Windows.
1Click [Safely Remove Hardware] on the task tray,
located at the lower right corner of the screen.
2 Click [Safely remove USB Mass Storage Device -
Drives (E:, F:, G:, H:, I:)].
3Make sure the message “The 'USB Mass Storage
Device' device can now be safely removed from
the system.” appears, and then disconnect the
reader/writer.
Note
The above steps are not required when removing a memory card
from the reader/writer.
For Windows 7
1Click the Start Button
2Click Devices and Printers.
3Right click [USB2.0 Card R/W] drive icon.
4 One by one ejects all removable disks or select
eject when all medias are inserted to drive.
5Pull the USB Cable out from computer.
Task tray
Click here.
The 'USB Mass Storage Device'
device can now be safely removed
from the system.
Click this icon.
Insert one of the following
cards in this slot:
•“Memory Stick Micro” (“M2”)
•“microSD Card and
microSDHC Card”
Solution
,Your computer and the reader/
writer may not be properly
connected. Disconnect the reader/
writer from the computer and
reconnect it.
,Your computer and the reader/
writer may not be properly
connected. See “Connecting the
Reader/Writer to a Computer” and
make sure the connection is correct.
,In Windows 7 case, the removable
disk icon appears after a memory
card inserted.
,No memory card is inserted. Insert a
memory card into the proper slot.
,The memory card is not fully
inserted. Insert the card completely.
,The memory card is not inserted
straight. Remove the card and insert
it again.
,The speed may vary depending on
the environment or the memory
card being used. This is not a
malfunction.
For Macintosh
1 Close the files saved on the memory card, and exit
any currently running applications.
2Make sure the access indicator is not blinking.
3Drag the removable disk icon to the [Trash].
Alternatively, select the removable disk icon, access the
[File] menu on the menu bar, and select [Eject “Untitled”]*.
*Depending on the memory card, a different label than “Untitled”
may be shown.
If no memory card is inserted into the reader/writer, skip
this step.
4Disconnect the reader/writer from the computer.
Installing the Drive Letter
Recognition Software
(Windows Only)
Before starting installation, read the “End User License
Agreement.”
1 Download the installer file from the web site.
The installer file can be downloaded from the following
URL
http://sony.storagesupport.com/
2Close all program that are still running.
3Double-click the installer file.
(For windows Vista and Windows 7, User Account Control
window will appear, click on [Allow].)
4When the following window appears, the
installing is completed, and click [OK].
Notes on Icons
Once the Drive Letter Recognition Software is installed, the
Removable Disk icons and their descriptions change.
For example, if the computer has an A:, C:, and D: drive before
connecting the reader/writer, the drive letters will be assigned
as follows when the reader/writer is connected:
Computer drive name Corresponding memory card
CF/Microdrive (E:) CompactFlash
MicroDrive
xD (F:) xD-Picture Card
MMC/SD (G:) MultiMediaCard
SD Memory Card
Memory Stick (H:) “Memory Stick” media
M2/microSD (I:) “Memory Stick Micro” (“M2”) media
microSD Card
Notes
• The use of this software is intended only for this reader/
writer. Other readers/writers may not work with this
software.
•Uninstall any similar software before installation to ensure
that the software functions properly.
Troubleshooting
Before consulting your Sony representative, verify the following.
If the problem still persists, consult your local Sony dealer.
Problem
The computer does not
detect the reader/writer.
The removable disk icon
does not appear.
The memory card cannot be
accessed with Windows
Explorer or My Computer.
The computer does not
recognize the memory card
The read/write speed is
slow.
Technical Support
Local technical support service is only available in the
following sales regions.
sFor customers in the USA (Sony Electronics Inc.)
Monday to Saturday,
8:00 a.m. - 8:00 p.m. Central Time
•Toll free: 1-800-588-3847
•Free telephone support is offered for 90 days after your first
call.
USA technical support only: Web- based technical support
is free and available 24 hours a day, 7 days a week.
•Web site:
http://sony.storagesupport.com/
1-YEAR LIMITED WARRANTY
For purchases in the U.S. see details at
www.mediabysony.com