Sony BDX-D1000 User manual

MPEG DECODER UNIT
BDX-D1000
DESCRAMBLER BOARD
BDKP-D1003
DESCRAMBLER BOARD
BDKP-D1004
INSTALLATION MANUAL
1st Edition (Revised 5)
Serial No. 10001 and Higher: BDX-D1000
Serial No. 10001 and Higher: BDKP-D1003
Serial No. 10001 and Higher: BDKP-D1004

BDX-D1000
!WARNING
This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so. Refer all servicing to
qualified service personnel.
!WARNUNG
DieAnleitung ist nur für qualifiziertes Fachpersonal bestimmt.
Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die
Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei
Wartungsarbeiten strikt dieAngaben in der Anleitung zu befolgen. Andere als die angegeben
Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung
dazu besitzen.
!AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin
de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les
réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.
Pour toute réparation faire appel à une personne compétente uniquement.
Attention-when the product is installed in Rack:
(For BDX-D1000)
1. Prevention against overloading of branch circuit
When this product is installed in a rack and is
supplied power from an outlet on the rack, please
make sure that the rack does not overload the supply
circuit.
2. Providing protective earth
When this product is installed in a rack and is
supplied power from an outlet on the rack, please
confirm that the outlet is provided with a suitable
protective earth connection.
3. Internal air ambient temperature of the rack
When this product is installed in a rack, please make
sure that the internal air ambient temperature of the
rack is within the specified limit of this product.
4. Prevention against achieving hazardous
condition due to uneven mechanical loading
When this product is installed in a rack, please make
sure that the rack does not achieve hazardous
condition due to uneven mechanical loading.

1 (E)
BDX-D1000
Table of Contents
Manual Structure
Purpose of this manual ........................................................................................ 3 (E)
Related manuals................................................................................................... 3 (E)
Contents ............................................................................................................... 3 (E)
Trademark............................................................................................................ 3 (E)
1. Installation
1-1. Installation Environment.......................................................................1-1 (E)
1-2. Power Supply ........................................................................................1-1 (E)
1-2-1. Power Specifications ............................................................1-1 (E)
1-2-2. Power Cord...........................................................................1-1 (E)
1-3. External Dimensions .............................................................................1-2 (E)
1-4. Rack Mounting......................................................................................1-2 (E)
1-5. Matching Connectors and Cables..........................................................1-5 (E)
1-6. Input and Output Signal of Connector ..................................................1-6 (E)
1-7. Switch Setting of Connector Panel .......................................................1-7 (E)
1-8. Settings of Internal Switches.................................................................1-8 (E)
1-8-1. DAC-31 Board .....................................................................1-8 (E)
1-8-2. DEC-99 Board (SUFFIX -14 and Higher) ...........................1-9 (E)
1-8-3. DEC-99 Board (SUFFIX -11 through -13) ........................1-10 (E)
1-9. Settings of Parameters.........................................................................1-11 (E)
2. Installation of Optional Boards
2-1. General Information for Installation .....................................................2-1 (E)
2-2. BDKP-D1003/D1004 Installation.........................................................2-2 (E)
3. Service Overview
3-1. Cleaning of Air Filter ............................................................................3-1 (E)
3-2. Description of Internal Indicators .........................................................3-2 (E)
3-2-1. DAC-31 Board .....................................................................3-2 (E)
3-2-2. DEC-99 Board (SUFFIX -14 and Higher) ...........................3-2 (E)
3-2-3. DEC-99 Board (SUFFIX -11 through -13) ..........................3-4 (E)
3-3. ISR.........................................................................................................3-4 (E)
3-3-1. Functions Overview .............................................................3-4 (E)
3-3-2. Usage of ISR Functions .......................................................3-5 (E)
3-3-3. Supported Commands ..........................................................3-8 (E)
3-3-4. Functions of Commands ......................................................3-8 (E)
3-4. Indicator on the Front Panel................................................................3-10 (E)

3 (E)
BDX-D1000
Purpose of this manual This manual is the installation manual of the BDX-D1000 MPEG Decoder Unit and
the following optional boards.
.Descrambler Board BDKP-D1003
.Descrambler Board BDKP-D1004
This manual is intended for use by trained system and service engineers, and
describes information regarding installation.
Related manuals Besides this installation manual, the following manuals are available for the
BDX-D1000.
..
..
.Operation Manual (Supplied with the BDX-D1000)
This manual explains the overview of the BDX-D1000, and the system configura-
tion examples.
..
..
.Maintenance Manual (Not supplied with the BDX-D1000)
This manual describes information that premise the service based on board
replacement and parts replacement (adjustments, board layouts, schematic dia-
grams, parts list, etc.).
If this manual is required, contact your local Sony Sales Office/Service Center.
Contents The following is a summary of all the sections for understanding the contents of this
manual.
Section 1 Installation
Explains the operating environment, the connector information for peripheral
equipment connections and how to rack mounting, etc.
Section 2 Installation of Optional Boards
Explains how to install the optional boards.
Section 3 Service Overview
Explains the description of internal indicators and summary of ISR.
Trademark
.Ethernet is a registered trademark of Xerox Corporation.
Manual Structure

1-1 (E)
BDX-D1000
Section 1
Installation
1-1. Installation Environment
Operating temperature : 5 dC to 40 dC
Storage temperature : _20 dC to +55 dC
Operating humidity : 20 % to 90 % (non-condensing)
Do not install the BDX-D1000 in the following locations:
.Areas where the unit will be exposed to direct sun light
or any other strong lights.
.Areas near heat sources.
.Dusty areas or areas where it is subject to vibration.
.Areas with strong electric or magnetic fields.
.Areas where is subjected to electricity noise.
.Areas where is subjected to static electricity noise.
To prevent the temperature rise inside the BDX-D1000,
pay careful attention to circulation of air in the place where
the BDX-D1000 is installed.
The rear side of the BDX-D1000 should be at least 20 cm
(8 inches) away from walls for ventilation and maintenance.
c
Do not block the ventilation holes.
If the ventilation holes are blocked, overheating inside the
unit may cause fire.
1-2. Power Supply
1-2-1. Power Specifications
Power requirements : AC 100 to 240 V
50/60 Hz
Current consumption : maximum 2.0 A (at 100 V)
maximum 1.0 A (at 240 V)
A switching regulator is used for the power supply of the
BDX-D1000. The voltage within the range of 100 V to
240 V can be used without changing the supply voltage.
n
As the inrush current at turn-on is maximum 20 A (at 100
V)/maximum 40 A (at 240 V), the capacity of the AC
power must be adequate with the inrush current of maxi-
mum 20 A (at 100 V)/maximum 40 A (at 240 V).
If the capacity of the AC power is not the adequately large,
the breaker of the AC power at the supply side will operate
or the BDX-D1000 will abnormal operate.
1-2-2. Power Cord
w
To avoid a fire or an electric shock, be sure to use the
designated power cord. And do not damage to the power
cord.
n
For the customer outside of the area as shown above or in a
part of Europe, the above-mentioned power cords can not
be used.
Use the power cord that is applicable to the places in the
world.
1 2
2
2
Power cord for the customer in the U.S.A. and Canada.
1Power cord set !1-557-377-11
2Plug holder (Black) 2-990-242-01
Power cord for the customer in the United Kingdom.
1DK-2401 (UK) (approx. 2.4 m)
2Plug holder (Black) 2-990-242-01
Plug holder is included in DK-2401 (UK).
Power cord for the customer in Europe except the
United Kingdom.
1DK-2401 (AE) (approx. 2.4 m)
2Plug holder (Brown) 3-613-640-01
Plug holder is included in DK-2401 (AE).
AC inlet
AC inlet
1
AC inlet
1

1-2 (E) BDX-D1000
1-3. External Dimensions
1-4. Rack Mounting
The BDX-D1000 can be mounted in a 19-inch standard rack.
n
.When the BDX-D1000 or the peripheral equipment is mounted in a 19-inch standard rack, it is recom-
mended to install a ventilation fan to prevent a temperature rise in the rack.
Make sure that all the units in the rack should be operated within the temperature range of 5 dC to 40 dC.
.Connect the enough long cables on the rear panel, considering that the BDX-D1000 is pulled out.
.An installation manual is supplied with the RMM-30 rack mount rail. However follow the instructions
in this manual. Because the rack mounting procedures of the BDX-D1000 are different from the
procedures explained in RMM-30 installation manual.
.To prevent falling the rack, fix the rack on the horizontal firm floor with bolts.
1-3. External Dimensions
1-4. Rack Mounting
(Front view) (Right side view)
(Top view)
Front panel
Unit : mm
Mass : 14 kg
885.2
469
424
450
304.883.7
44
76.2
88 (2U)14.5
254
101.6
482
465
424
482

1-3 (E)
BDX-D1000
Required parts
.Rack Mount Rail, RMM-30
Rail with bracket : 2 pcs.
Screw (B5x8) : 8 pcs.
.Screw for inner rail (B4x8) (*1) : 6 pcs.
.Screw for rack mounting (RK5x16) : 4 pcs.
(Sony part number: 7-682-378-04)
.Washer for rack mounting : 4 pcs.
(Sony part number: 2-297-913-01)
(*1) : The BDX-D1000 comes with the eight screws. The
two screws of them are spare.
n
Be sure to use the RMM-30 Rack Mount Rail.
If a rack mount rail other than the RMM-30 is used, the
BDX-D1000 may be dropped by insufficient strength of
the rack mount rail. This may cause a injury.
Procedures
1. Turn the power off.
2. Remove the four feet from the bottom of the BDX-
D1000.
1-4. Rack Mounting
3. While pressing the stopper of the rail, pull out the
inner rail.
4. Attach the inner rails to the BDX-D1000 using the six
screws (B4x8) supplied with the BDX-D1000.
5. Loosen the screws fastening the rear bracket to the
outer rail, and adjust the position of the rear bracket
with the rack depth.
Feet
BVTT 3x12 Feet
BVTT 3x12
Inner rail
Inner rail
B 4x8
B 4x8
Rear bracket
Front bracket
Outer rail
Stopper
Inner rail
Outer rail

1-4 (E) BDX-D1000
6. Attach the front and rear brackets to the outside of the
rack temporarily using the eight screws (B5x8)
supplied with RMM-30.
7. While pressing the stoppers of the inner rails, slide the
inner rails fully into the outer rails.
w
.Be sure to mount the BDX-D1000 in the rack with two
or more persons.
Trying to handle this job by one-person could occur to
injury.
.Be careful not to get caught your hand and finger in the
rack mount rail when installing the unit in the rack.
8. After confirming that the BDX-D1000 can be moved
smoothly, tighten the screws (B5x8) secured tempo-
rarily in the step 6.
n
When securing the front brackets to the rack by
screws, pull out the BDX-D1000 about 20 cm (8
inches), and fasten the screws of the front brackets to
the rack.
9. After installing the BDX-D1000 in the rack, secure the
unit to the rack by the prepared four screws (RK5x16)
and four washers.
n
When the BDX-D1000 is mounted in a rack, the maximum
traveling distance is illustrated below.
1-4. Rack Mounting
RK 5x16
Washers
Washers
RK 5x16
Rack
Rack
Rack
Unit : mm
12.7
12.7
31.75
12.7
31.75
B 5x8B 5x8
Outer rails
Front bracket
Rear bracket
Rack
Stopper
Inner rail
Outer rail
88
44
581 (Maximum traveling distance)
Distance to the center of the side rail
Height of the unit mounted in a rack Unit : mm