Southern Enterprises 349100TX User manual

1
HZ349100TX Shelf - Light Maple
HZ349200TX Shelf - Black
Assembly Instructions
For assistance with assembly, contact:
Southern Enterprises Inc.
Customer Service 1-800-633-5096
[e-mail]
www.seidal.com
PO#

2
Tool List: 3/16" drill bit, drill, tape measure and pencil
Shelf
Parts List
Please check packaging for all parts and hardware before discarding. Unpack and lay parts on clean, padded
surface like carpet or blanket. Check that you have all parts indicated. Call customer service if hardware is missing.
Before beginning assembly, carefully study the diagrams below and sort your hardware according to the pictures.
Using the incorrect hardware will cause damage.
A Quantity
Of 2
plastic anchor
Dia. 1/4” x 1-3/16”L
B Quantity
Of 12
screw
Dia. 5/16“ x 1-1/2”L
C Quantity
Of 10
sticker cover
D
Quantity
of 1
leveler
E Quantity
Of 1
board
F Quantity
Of 1
board
G Quantity
Of 1
board
H Quantity
Of 3
board
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Periodically apply furniture wax to renew
the finish. Avoid rubbing or scratching the
surface with rough or abrasive objects.
For replacement parts or questions, please
call customer service at 1-800-633-5096.
Assembly Tool Required
No.2 Phillips Screwdriver
Not Included

3
Figure 1
Connect board (E) to board (H)
with 2pcs screws (B).
Tighten screw with Philips
screwdriver.
Repeat step for board (F) and
board (G).
Figure 2
Connect assembled units together
with 4pcs screws (B) as shown in
figure 2.
Figure 3
Cover the screw holes with sticker
covers (C) as shown in figure 3.
Shelf
Assembly Instructions

4
NOTE: NO DRILLED HOLE OR PLASTIC ANCHOR
REQUIRED WHEN MOUNTING TO WOOD WALL.USE
SCREW ONLY. WE DO NOT SUPPLY HARDWARE FOR
MOUNTING ON CONCRETE WALLS
Figure 4
Find a desired location on the wall and
mark two locations for the screws.
One screw (for each unit) must be
attached directly into a wall stud. Wall
anchors are not needed when mounting
onto a wall stud.
Drill one 3/16" hole (for each unit) on the
marked location.
Insert a plastic anchor (A) into the hole
on the wall as shown; you will need a
hammer when doing this.
Using the phillips head screwdriver,
install screw (B) into the anchor (A) and
the other screw installed into the wall
stud.
Turn the screws (B) until there is a gap
of approximately 13 mm between the
head of the screw and the wall as
shown in figure 4.
Figure 5
Hang the assembled unit onto the
screws (B) and verify the shelf is resting
securely on the mounting screw (B).
Use a leveler to insure the product is
level.
Now you shelf is ready to use.
T
he hole
measurement
s
on
the
wall must match with the hole
measurements on back of the
unit"

5
Please immediately examine this product carefully. Any request for missing parts or damage replacement
must be received within 90 days of your receipt of the product. Replacement, if available, will be honored
within this time frame.Parts will not be available for items arriving fully assembled. We do not recommend
modifying product(s) and we are not responsible for any damages due to product modification(s). If
damages or missing parts are not reported within 90 days of your receipt, we are under no obligation to
provide parts or replacement merchandise.
Please contact Southern Enterprises at 800-633-5096 or in Dallas 972-869-0111/ 9am – 4pm Mon-Fri
Central time if you have product issues or email us at serv[email protected]. Please ask for customer service
representative for issues involving damages or replacement parts. Please ask for technical assistance
representative for any issues with product and assembly/construction.
Please contact the retailer that you purchased from for returns.
Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/Website/Catalog
Please indicate color/size/style number:
Style No Parts Letter Parts Description Quantity
Needed
Customer Service 1-800-633-5096
[e-mail]
Southern Enterprises Inc.
600 Freeport Parkway, Suite 200
Coppell, Texas 75019
Parts Replacement Form

6
CAUTION
Max shelf load capacity is achieved by mounting screw into studs or cement
walls.
If mounting to sheet rock (cavity wall) it is advisable to mount at least 1 screw
(without anchor) directly to a wall stud or studs However do not leave either end of
mounting bracket unsupported by at least one anchor For hollow wall mounting you
can use any of the holes in the back plate to suit where you require the mounting
screws positioned