Southern Enterprises Larkin MS340500TX User manual

MS340500TX
Larkin Media Console
Assembly Instructions
For assistance with assembly, contact:
Southern Enterprises Inc.
Customer Service 1-800-633-5096
[email protected]om
www.seidal.com
Page 1

A.
Quantity
of 1
Top Panel
B.
Quantity
of 1
Bottom Panel
C.
Quantity
of 1
Middle Panel
D.
Quantity
of 1
Left Vertical Panel
E.
Quantity
of 1
Right Vertical Panel
F.
Quantity
of 1
Left Side Panel
G.
Quantity
of 1
Right Side Panel
H.
Quantity
of 1
Fixed Shelf Panel
I.
Quantity
of 1
Left Door
J.
Quantity
of 1
Right Door
K
.
Quantity
of 4
Leg
L.
Quantity
of 1
Back Panel
1
Quantity
of 20
Cam Bolt
2
Quantity
of 20
Cam Lock
3
Quantity
of 20
Wood Dowel: Dia5/16”x1-1/4”
4
.
Quantity
of 18
Screw: Dia 1/8”x1/2”
5
.
Quantity
of 4
Small Bolt: Dia5/32”x3/4”
6
.
Quantity
of 26
Screw: Dia 1/8”x1/2”
Larkin Media Console
Parts list
Please check packaging for all parts and hardware before discarding. Unpack and lay parts on clean,
padded surface like carpet or blanket. Check that you have all parts indicated. Call customer service if
hardware is missing. Before beginning assembly, carefully study the diagrams below and sort your
hardware according to the pictures. Using the incorrect hardware will cause damage.
Page 2

7
.
Quantity
of 4
Hinge
8
.
Quantity
of 2
Handle
9
.
Quantity
of 8
Bolt: Dia1/4”x2”
10.
Quantity
of 1
Allen Wrench
11
.
Quantity
of 4
Double
Sided Bolt: Dia5/16”x2-3/4”
12
.
Quantity
of 4
Half Moon Washer
13
.
Quantity
of 4
Nut
14
.
Quantity
of 1
Wrench
15
.
Quantity
of 2
Magnet
16.
Quantity
of 2
Magnet Plate
17
.
Quantity
of 4
Screw: Dia 1/8”x5/8”
18
.
Quantity
of 4
Screw: Dia1/8”x1-3/8”
19
.
Quantity
of 4
Bracket
20
.
Quantity
of 2
Plastic Strap
21
.
Quantity
of 4
Plastic Anchor
22.
Quantity
of 20
Cover
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Periodically apply furniture wax to renew
the finish.Avoid rubbing or scratching the
surface with rough or abrasive objects.
Call customer service at 1-800-633-5096
for assistance, questions, or Parts.
Assembly Tool Required No.2 Phi
Tool List: 3/16" Drill Bit, Drill, Tape Measure and Pencil.
Page 3
Assembly Tool Required No.2 Phillips
Screwdriver (Not included)

Figure
1
Screw Double Sided Bolts (11) into
each Leg (K) as shown.
Figure
2
Insert the attached Double Sided
Bolts (11) on the Legs (K) into the
corresponding holes on Bottom
Panel (B).
Insert the Half Moon Washers (12)
into the large holes on the bottom of
Bottom Panel (B) and insert them
onto the Double Sided Bolts (11).
Screw Nuts (13) onto the Double
Sided Bolts (11) to secure the Legs
(K) onto the Bottom Panel (B).
Tighten Nuts (13) with Wrench (14).
Larkin Media Console
Assembly Instructions


 


Page 4

Figure
3
Turn the assembled unit from
Figure 2 right side up.
Attach Middle Panel (C) onto the
unit from Figure 2 with Bolts (9).
Tighten Bolts with Allen Wrench
(10).
Figure 4
Screw Cam Bolts (1) into threaded
holes on Left Vertical Panel (D) and
Right Vertical Panel (E).
Insert Wood Dowels (3) into
corresponding holes on Fixed Shelf
Panel (H).
Attach Left Vertical Panel (D) and
Right Vertical Panel (E) onto Fixed
Shelf Panel (H) by inserting
attached Wood Dowels (3) and
Cam Bolts (1) into corresponding
holes until all panels meet.
Insert Cam Locks (2) into
corresponding holes on Fixed Shelf
Panel (H).
Rotate Cam Locks (2) clockwise
with Phillips screwdriver to secure
panels.
P
age
5






















Figure 5
Screw Cam Bolts (3) into
corresponding threaded holes on
Middle Panel (C). Insert Wood
Dowels (3) into corresponding holes
on Middle Panel (C).
Attach assembled unit from Figure
4 onto Middle Panel (C) by inserting
Wood Dowels (3) and Cam Bolts (1)
into corresponding holes until all
panels meet.
Insert Cam Locks (2) into the
corresponding holes on the
assembled unit from Figure 4.
Tighten by rotating Cam Locks (2)
clockwise with Phillips screwdriver.
Figure 6
Screw Cam Bolts (1) into
corresponding threaded holes and
insert Wood Dowels (3) on the four
corners of assembled unit from
Figure 5.
Attach Left Side Panel (F) and Right
Side Panel (G) to assembled unit
from Figure 5 by inserting Wood
Dowels (3) and Cam Bolts (1) into
corresponding holes until all panels
meet.
Insert Cam Locks (2) into
corresponding holes on Left Side
Panel (F) and Right Side Panel (G).
Tighten by rotating Cam Locks (2)
clockwise with Phillips screwdriver,
Page 6
















Figure
7
Attach Magnet (15) to Top Panel
(A) with Screws (6).
Tighten screws with Phillips
screwdriver.
Figure
8
Screw Cam Bolts (1) and insert
Wood Dowels (3) into Top Panel
(A).
Attach Top Panel (A) to the
assembled unit from Figure 6 by
inserting Wood Dowels (3) and
Cam Bolts (1) into corresponding
holes until all panels meet.
Insert Cam Locks (2) into
corresponding holes on the
assembled unit from Figure 6.
Tighten by rotating Cam Locks (2)
clockwise with Phillips screwdriver.
Page 7








Figure 9
Attach Back Panel (L) to the
assembled unit from Figure 8 with
Screws (6).
Tighten screws with Phillips
screwdriver.
Figure 10
Attach Hinge (7) and Magnet Plate
(16) to Left Door (I) with Screws
(4).
Tighten screws with Phillips
screwdriver.
Attach Handle (8) to Left Door (I)
with Bolts (5).
Tighten bolts with Phillips
screwdriver.
Figure 11
Attach Hinge (7) and Magnet Plate
(16) to Right Door (J) with Screws
(4).
Tighten screws with Phillips
screwdriver.
Attach Handle (8) to Right Door (J)
with Bolts (5).
Tighten bolts with Phillips
screwdriver.



















Page 8

Figure 12
Attach doors to the assembled
unit from Figure 9 with Screws
(4).
Tighten screws with Phillips
screwdriver.
Cover cam lock hole with Cover
(22).
Figure 13
Attach Brackets (19) to Back
Panel using Screws (17).
Tighten Screws (17) using Philips
screwdriver.



Page 9

Figure 14
Mark two desired locations on the
wall matching the distance of the
Brackets (19) on the back of the
unit and Drill them with a 3/16"
drill bit.
Insert Plastic Anchors (21) into
the 2 holes on wall as shown.
(When doing this, you will need a
hammer help you).
Then, attach the Brackets (19) to
the wall using Screws (18).
Tighten Screws (18) using Philips
screwdriver.
Figure
1
5
Move this item close to the wall
Brackets (19) and tie in both
Brackets (19) with Plastic Straps
(20) as shown in diagram.
Anti-tipping hardware
must be used for this
produ t to avoid tipping
and injury.
Wall





Page 10