Southern Enterprises HZ102800TX User manual

Page | 1
For assistance with assembly, contact:
Southern Enterprises Inc.
Customer Service 1-800-633-5096
[email protected]m
www.seidal.com
HZ102800TX
Dowd Cabinet
Assembly Instructions
PO#:

Page | 2
Dowd Cabinet
Assembly Instructions
Please check packaging for all parts and hardware before discarding. Unpack and lay parts on clean, padded
surface like carpet or blanket. Check that you have all parts indicated. Call customer service if hardware is missing.
Before beginning assembly, carefully study the diagrams below and sort your hardware according to the pictures.
Using the incorrect hardware will cause damage.
A.
Quantity
of 1
Top Panel
B.
Quantity
of 1
Bottom Panel
C.
Quantity
of 1
Left Side Panel
D.
Quantity
of 1
Right Side Panel
E.
Quantity
of 1
Lower Fixed Shelf Panel
F.
Quantity
of 1
Upper Fixed Shelf Panel
G.
Quantity
of 1
Middle Vertical Panel
H.
Quantity
of 1
Front Crosspiece
I.
Quantity
of 1
Back Crosspiece
J.
Quantity
of 1
Left Door
K.
Quantity
of 1
Right Door
L.
Quantity
of 2
Drawer Front Panel

Page | 3
M.
Quantity
of 2
Drawer Left Panel
N.
Quantity
of 2
Drawer Right Panel
O.
Quantity
of 2
Drawer Right Panel
P.
Quantity
of 2
Drawer Bottom Panel
Q.
Quantity
of 1
Back Panel
R.
Quantity
of 4
Leg
1.
Quantity
of 22
Cam Bolt
2.
Quantity
of 22
Cam Lock
3.
Quantity
of 18
Wood Dowel Ø 8 x 30mm
4.
Quantity
of 56
Flat Head Screw
∅
1/8"x
1/2"
5.
Quantity
of 4
Bolt for Handle
∅
5/32"x3/4"
6.
Quantity
of 28
Round Head Screw
Ø 1/8” x 5/8”L
(for Back Panel and Magnet)
7.
Quantity
of 6
Hinge
8.
Quantity
of 8
Bolt
∅
1/4"x2-3/4"L
9.
Quantity
of 1
Allen Wrench

Page | 4
10.
Quantity
of 21
Screw
∅
1/8"x
1
"
11.
Quantity
of 4
Handle
12.
Quantity
of 2
Magnet
13.
Quantity
of 2
Magnet Plate
14.
Quantity
of 4
Screw
∅
1/8"x5/8"
15.
Quantity
of 4
Screw
Ø 1/8” x 1-5/8”L
16.
Quantity
of 4
Bracket
17.
Quantity
of 4
Anchor
18.
Quantity
of 2
Plastic Strap
19.
Quantity
of 8
Cover
20.
Quantity
of 4
Drawer Slide
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Periodically apply furniture wax to renew
the finish. Avoid rubbing or scratching the
surface with rough or abrasive objects.
For replacement parts or questions, please
call customer service at 1-800-633-5096.
Assembly Tool Required No.2 Phillips
Screwdriver (Not Included)

Page | 5
Figure 1
Please separate Drawer Slides (20) into
male and female components as shown.
Note: There is a lever located on the
male slide. Push the lever to the
either side while pulling in order to
detach the male slide from the female
slide.
Figure 2
Screw with fingers to help align screws
before using screwdriver.
Attach Female Drawer Slide (20)
components to Left Side Panel (C) using
Flat Head Screws (4).
Tighten Flat Head Screws (4) with
Phillips screwdriver.
Note: When attaching the female
slides, make sure to insert wood
screws through the first opening
starting from the front, then align
the openings to the pre-drilled
holes on the panels.
Dowd Cabinet
Assembly Instructions

Page | 6
Figure 3
Attach Female Drawer Slide (20) to
Right Side Panel (D) using Flat Head
Screws (4).
Tighten Flat Head Screws (4) with
Phillips screwdriver.
Figure
4
Attach two Female Drawer Slides (20) to
Middle Vertical Panel (G) using Flat
Head Screws (4).
Tighten Flat Head Screws (4) with
Phillips screwdriver.

Page | 7
Figure 5
Screw with fingers to help align cam
bolts before using screwdriver.
Insert Cam Locks (2) into corresponding
holes on Middle Vertical Panel (G).
Screw Cam Bolts (1) and insert Wood
Dowels (3) into corresponding holes on
Lower Fixed Shelf Panel (E) and Upper
Fixed Shelf Panel (F).
Attach Lower Fixed Shelf Panel (E) and
Upper Fixed Shelf Panel (F) to Middle
Vertical Panel (G) by inserting Wood
Dowels (3) and Cam Bolts (1) into
corresponding holes until panels meet.
Tighten by rotating Cam Locks (2)
clockwise with Phillips screwdriver.
Attach Back Crosspiece (I) to Middle
Vertical Panel (G) using Screws (10).
Tighten Screws (10) with Phillips
screwdriver.
Notice: Make sure that all finished
edges are facing towards the front of
the unit.
Figure 6
Attach Magnets (12) to Front Crosspiece
(H) using Round Head Screw (6) as
shown.
Tighten Round Head Screw (6) with
Phillips screwdriver.

Page | 8
Figure 7
Insert Cam Locks (2) into corresponding
holes on assembled unit from Figure 5
Screw Cam Bolts (1) and insert Wood
Dowels (3) into corresponding holes on
Left Side Panel (C) and Right Side
Panel (D).
Attach Left Side Panel (C), Right Side
Panel (D) and Front Crosspiece (H) to
assembled unit from Figure 6 by
inserting Wood Dowels (3) and Cam
Bolts (1) into corresponding holes until
Left Side Panel (C), Right Side Panel
(D) and Front Crosspiece (H) and
assembled unit from Figure 5 meet.
Tighten by rotating Cam Locks (2)
clockwise with Phillips screwdriver.
Figure 8
Attach Legs (R) to Bottom Panel (B)
using Bolt (8) as shown.
Tighten Bolt (8) with Allen Wrench (8).

Page | 9
Figure 9
Insert Cam Locks (2) into corresponding
holes on assembled unit from Figure 7.
Screw Cam Bolts (1) and insert Wood
Dowels (3) into corresponding holes on
Top Panel (A) and Bottom Panel (B).
Attach Top Panel (A) and Bottom Panel
(B) to assembled unit from Figure 7 by
inserting Wood Dowels (3) and Cam
Bolts (1) into corresponding holes until
Top Panel (A) and Bottom Panel (B) and
assembled unit from Figure 7 meet.
Tighten by rotating Cam Locks (2)
clockwise with Phillips screwdriver.
Figure 10
Attach Back Panel (Q) to backside of the
assembled of the unit with Round Head
Screws (6).
Tighten Screws (6) with a Phillips
screwdriver.

Page | 10
Figure 11
Attach the Metal Plate (13) on the inner
inside of the Left Door (J) using Flat
Head Screws (4)
Attach the Hinges (7) to the Door (I)
using Flat Head Screws (4)
Tighten Flat Head Screws (4) with
Phillips screwdriver.
Attach the Door Handle (11) on the door
using Bolt for Handle (5).
Tighten Bolt (5) with Phillips screwdriver
Figure 12
Attach the Metal Plate (13) to the inner
inside of the Right Door (K) using Flat
Head Screws (4)
Attach the Hinges (7) to the Door (I)
using Flat Head Screws (4)
Tighten Flat Head Screws (4) with
Phillips screwdriver.
Attach the Door Handle (11) to the door
using Bolt for Handle (5).
Tighten Bolt (5) with Phillips screwdriver