Southern Enterprises HZ104100TX User manual

For assistance with assembly contact:
Southern Enterprises, Inc.
Customer Service 1-800- 33-509
[e-mail]
www.seidal.com
HZ104100TX
Black Contemporary Bar
Cabinet
ASSEMBLY I STRUCTIO
PO#：
P
age 1

A.
Quantity
of 1
top panel
B.
Quantity
of 1
bottom panel
C.
Quantity
of 1
left side panel
D.
Quantity
of 1
right side panel
E.
Quantity
of 2
Fixed shelf panel
F.
Quantity
of 1
Back panel
G.
Quantity
of 3
Wine rack shelf panel
H.
Quantity
of 4
Wine rack vertical panel
I.
Quantity
of 1
Left door
J.
Quantity
of 1
Right door
K.
Quantity
of 4
Wine rack shelf panel
L.
Quantity
of 1
drawer front
M.
Quantity
of 1
Drawer side left
N.
Quantity
of 1
Drawer side right
O.
Quantity
of 1
Drawer back
Black Contemporary Bar Cabinet
Parts list
Please review all parts and hardware before disposing of any packaging.
Call Customer Service if missing hardware.
Using a screw that is too long will cause damage.
Before beginning assembly, separate each type of screw. Carefully study the
diagrams below. You may receive extra hardware with your unit.
Page 2
up

P
Quantity
of 1
Drawer bottom
Q
Quantity
of 4
Middle glass rack
R
Quantity
of 2
Side Glass rack
S
Quantity
of 4
Legs
T
Quantity
of 4
Metal rack
1
Quantity
of 32
Wood Dowel
Dia5/16”x1-3/16”L
2
Quantity
of 32
cam bolt
3.
Q
uantity
of 32
Cam lock
4.
Quantity
of 6
hinge
5.
Quantity
of 86
screw :Dia1/8”x1/2”L
.
Quantity
of 22
screw :Dia1/8”x1/2”L
7
.
Quantity
of 2
knob
8
.
Quantity
of 2
Small bolt
9.
Quantity
of 2
Door catch
10.
Quantity
of 1
Female slide left
11
.
Quantity
of 1
male slide left
1
2
.
Quantity
of 1
Female slide right
13.
Quantity
of 1
male slide right
Page 3

14.
Quantity
of 4
Metal bracket
15
.
Quantity
of 18
screw :Dia1/8”x1-1/4”L
1
.
Quantity
of 4
screw :Dia1/8”x1”L
17.
Quantity
of 4
screw :Dia1/8”x5/8”L
18.
Quantity
of 2
bracket
19.
Quantity
of 2
Plastic chain
20
.
Quantity
of 2
anchor
21.
Quantity
of 4
screw :Dia1/8”x1-3/8”L
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Periodically apply furniture wax to renew
the finish. Avoid rubbing or scratching the
surface with rough or abrasive objects.
For replacement parts or questions, please
Call Customer Service at 1-800-633-5096
please call Manufacturer for assistance, questions or
Parts.
Assembly Tool Required No.2 Phi
Tool List: 3/1 " drill bit, drill, tape measure and pencil.
Page 4
Assembly Tool Required No.2 Phillips
Screwdriver (Not included)

Figure 1
Assembly Instructions:
Wood may scratch easily, Be careful
when assembling. Do not scratch.
Attach female slide left (10) to
left side panel(C) with screw
(5).
Tighten screws with a phillips
screwdriver (not included)
Figure
2
Attach female slide right (12)
to right side panel (D) with
screw (5),
Tighten screws with a phillips
screwdriver.
Black Contemporary Bar Cabinet
Assembly Instructions
Page 5

Figure 3
Insert cam lock (3) into predrilled
holes on fixed shelf panel (E)
Screw cam bolt (2) into pre-drilled
holes on left side panel (C). Attach
left side panel (C) to fixed shelf
panel (E) by inserting wood dowel
(1) & cam bolt (2) into
corresponding pre-drilled holes until
left side panel (C) & fixed shelf
panel (E) meet.
Tighten by rotating cam lock (3)
clockwise with a
Phillips screwdriver
Repeat above procedure to attach
right side panel (D) to (E)
Figure
4
Insert cam lock (3) into predrilled
holes on pre-assembled unit on
figure 3
Screw cam bolt (2) into pre-drilled
holes on top panel (A). Attach top
panel (A) to pre-assembled unit on
figure 3 by inserting wood dowel (1)
& cam bolt (2) into corresponding
pre-drilled holes until top panel (A)
& pre-assembled unit on figure 4
meet.
Tighten by rotating cam lock (3)
clockwise with a Phillips
screwdriver.
Attach door catch (9) to top panel
(A) with screw (6).
Tighten screws with a Phillips
screwdriver.
Figure
5
Insert cam lock (3) into predrilled
holes on pre-assembled unit on
figure 4.
Screw cam bolt (2) into pre-drilled
holes on bottom panel (B). Attach
bottom panel (B) to pre-assembled
on figure 4 by inserting wood dowel
(1) & cam bolt (2) into
corresponding pre-drilled holes until
bottom panel (B) & pre-assembled
unit on figure 4 meet.
Tighten by rotating cam lock (3)
clockwise with a Phillips screwdriver
Attach door catch (9) to bottom
panel (B) with screw (6).
Tighten screws with a Phillips
screwdriver.
Page 6
3
E
E
C
D
B
2
2166

Figure
Attach leg (S) to pre-assembled unit
on figure 5 by hand.
Attach middle glass rack (Q) & side
glass rack (R) to pre-assembled
unit on figure 5 with screw (15).
Tighten with a Phillips screwdriver.
Figure 7
Attach wine rack vertical panel (H)
& wine rack shelf panel (G) together
as shown.
Figure 8
Insert pre-assembled unit on figure
7 to pre-assembled unit on figure 6
from back as shown.
Page 7
R

Figure 9
Attach back panel (F) to back side
of pre-assembled unit on figure 8
with screw (6).
Tighten screws with a Phillips
screwdriver.
Figure 10
Attach metal rack (T) to left door (I)
& right door (J) with screw (5).
Attach knob (7) to left door (I) &
right door (J) with small bolt (8).
Tighten screws &small bolt with a
Phillips screwdriver.
Figure
11
Insert cam lock (3) into predrilled
holes on wine rack shelf (K)
Screw cam bolt (2) into pre-drilled
holes on pre-assembled unit on
figure10. Attach wine rack shelf (K)
to pre-assembled on figure 10 by
inserting wood dowel (1) & cam bolt
(2) into corresponding pre-drilled
holes until wine rack shelf (K) &
pre-assembled unit meet.
Tighten by rotating cam lock (3)
clockwise with a Phillips
screwdriver.
Page 8
F
up
6
6
6
66
6
6
6
6
6
6
7
8
I/J
T
T
22

Figure 12
Attach metal bracket (14) to
pre-assembled unit on figure
11 with screw 5.
Tighten screw with a phillips
screwdriver.
Figure 13
Attach hinge (4) to the inside
pre-assembled on figure 12 &
figure 9 with screw (5).
Tighten screws with a Phillips
screwdriver.
5
4
4
4
555
4
55
5
5
5
5
5
5
Page 9

Figure 14
Attach the drawer side panel left
(M) & drawer side panel right (N) to
drawer back panel (O) and line up
the groove. Secure them with
screw (16).
Insert drawer bottom panel (P) into
the corresponding groove of
drawer back panel (O) & drawer
side panel left (M) & drawer side
right (N).
Insert cam lock (2) into predrilled
hole on drawer side panel left (M) &
drawer side panel right (N). Screw
cam bolt into predrilled on drawer
front (L),
Attach drawer front (L) to drawer
box by inserting cam bolt (2) into
corresponding pre-drilled holes
until drawer front (L) & drawer box
meet.
Tighten by rotating cam lock (3)
clockwise with a Phillips
screwdriver.
Figure 15
Attach male slide left (11)& male
slide right (13) with screw (5) to
pre-assembled unit on figure 14.
Tighten screw with a Phillips
screwdriver.
2
5
55