Southern Enterprises Boyle HZ103700TX User manual

HZ103700TX
Boyle Bar Cabinet
Assembly Instructions
Page 1
For assistance with assembly, contact:
Southern Enterprises Inc.
Customer Service 1-800- 33-509
[e-mail]
www.seidal.com

A.
Quantity
of 1
Top Panel
B.
Quantity
of 1
Bottom Panel
C.
Quantity
of 1
Left Side Panel
D.
Quantity
of 1
Right Side Panel
E.
Quantity
of 1
Middle Vertical Panel
F.
Quantity
of 1
Left Fixed Shelf Panel
.
Quantity
of 1
Right Fixed Shelf Panel
H.
Quantity
of 2
Wine Rack Panel
I.
Quantity
of 1
Left Door
J.
Quantity
of 1
Right Door
K.
Quantity
of 1
Left Back Panel
L.
Quantity
of 1
Right Back Panel
Boyle Bar Cabinet
Parts list
Please check packaging for all parts and hardware before discarding. Unpack and lay parts on clean,
padded surface like carpet or blanket. Check that you have all parts indicated. Call customer service if
hardware is missing. Before beginning assembly, carefully study the diagrams below and sort your
hardware according to the pictures. Using the incorrect hardware will cause damage.
Page 2

M.
Quantity
of 2
Wood Handle
N.
Quantity
of 2
Front Leg
O.
Quantity
of 2
Back Leg
1
Quantity
of 20
Cam Bolt
2
Quantity
of 20
Cam Lock
3
Quantity
of 20
Wood Dowel: Dia5/16”x1-1/4”
4.
Quantity
of 44
Screw: 1/8”x1/2”
5.
Quantity
of 4
Small Bolt: Dia5/32”x1”
6.
Quantity
of 2
Screw: 1/8”x5/8”
7
.
Quantity
of
inge
8.
Quantity
of 1
Bolt: 5/16”x1”
9.
Quantity
of 1
Allen Wrench
10
.
Quantity
of 2
Magnet
11.
Quantity
of 2
Metal Plate
12.
Quantity
of 4
Screw: 1/8”x5/8”
13.
Quantity
of 4
Screw: 1/8”x1-5/8”
14.
Quantity
of 4
Brackets
15.
Quantity
of 2
Plastic Straps
Page 3

16.
Quantity
of 4
Plastic Anchor
17.
Quantity
of 20
Covers
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Periodically apply furniture wax to renew
the finish. Avoid rubbing or scratching the
surface with rough or abrasive objects.
Call customer service at 1-800- 33-509
for assistance, questions, or Parts.
Assembly Tool Required No.2 Phi
Tool List: 3/16" Drill Bit, Drill, Tape Measure and encil.
Page 4
Assembly Tool Required No.2 Phillips
Screwdriver (Not included)

Figure 1
Attach Magnets (10) to Top Panel
(A) with Screw (6).
Tighten Screws with Phillips
screwdriver.
Figure 2
Distinguish which side is the front of
Bottom Panel (B).
Attach Front Legs (N) towards the
front of Bottom Panel (B) and the
Back Legs (O) towards the rear with
Bolt (8).
Tighten bolts with Allen Wrench (9).
Notice: Each Leg has a slight
taper. Make sure the Front Legs
(N) are tapered towards the front
of the Bottom Panel (B) while the
Back Legs (O) are tapered
towards the rear.
Boyle Bar Cabinet
Assembly Instructions
Page 5
front

Figure 3
Insert Cam Locks (2) into
corresponding holes on Left Fixed
Shelf Panel (F) and Right Fixed
Shelf Panel ( ).
Screw Cam Bolts (1) into threaded
holes and insert Wood Dowels (3)
into both sides of Middle Vertical
Panel (E).
Attach Left Fixed Shelf Panel (F)
and Right Fixed Shelf Panel ( ) to
Middle Vertical Panel (E) by
inserting Wood Dowels (3) and Cam
Bolts (1) into corresponding holes
until panels meet.
Tighten Cam Locks (2) by rotating
clockwise with Phillips screwdriver.
Figure 4
Insert Cam Locks (2) into
corresponding holes on the
assembled unit from Figure 3.
Screw Cam Bolts (1) into threaded
holes on Left Side Panel (C) and
Right Side Panel (D). Then, insert
Wood Dowels (3) into the
corresponding holes between the
Cam Bolts.
Attach Left Side Panel (C) and
Right Side Panel (D) to the
assembled unit from Figure 3 by
inserting Wood Dowels (3) and Cam
Bolts (1) into corresponding holes
until panels meet.
Tighten by rotating Cam Locks (2)
clockwise with Phillips screwdriver.
FE
Page 6

Figure 5
Insert Cam Lock (2) into the
corresponding holes on the
assembled unit from Figure 4.
Screw Cam Bolts (1) into threaded
holes on Top Panel (A) and Bottom
Panel (B). Then, insert Wood
Dowels (3) into the corresponding
holes between the Cam Bolts.
Attach the assembled unit from
Figure 4 to Top Panel (A) and
Bottom Panel (B) by inserting Wood
Dowels (3) and Cam Bolts (1) into
corresponding holes until panels
meet.
Tighten by rotating Cam Locks (2)
clockwise with Phillips screwdriver.
Figure 6
Attach Back Panels (L/K) to the
assembled unit Screws (6).
Tighten screws with Phillips
screwdriver.
Page 7
2
3
3

Figure 7
Attach Hinges (7) and Metal Plates
(11) to Left Door (I) with Screws (4).
Attach Wood Handle (M) to Left
Door (I) with Bolts (5).
Tighten bolts and screws with
Phillip screwdriver.
Figure 8
Attach Hinges (7) and Metal Plates
(11) to Right Door (J) with Screws
(4).
Attach Wood Handle (M) to Right
Door (J) with Bolts (5).
Tighten bolts and screws with
Phillip screwdriver.
Page 8
4
11
7
7
7
J
11
7
7
7

Figure 9
Attach Doors (I/J) to the assembled
unit with Screws (4).
Tighten screws with Phillips
screwdriver.
Cover all cam lock holes with
Covers (17).
Figure 10
Insert Wine Rack Panels (H) into
the assembled unit as shown.
Page 9
17

Figure 11
Mark two desired locations on wall.
Drill two 3/1 " holes on wall for
each Bracket (14) matching the
distance of the Brackets installed to
the back of the unit (see Figure 11)
.
Insert Plastic Anchors (16) into the
holes on wall as shown. (When
doing this, you will need a hammer
help you).
Then, attach the Brackets (14) to
wall using Screws (13).
Tighten Screws (13) using Philips
screwdriver.
Figure 12
Attach Brackets (14) to Back
Panels using Screws (12).
Tighten Screws (12) using Philips
screwdriver.
Wall
16 14
13
13
14
16
Page 10
14
12
14
12