Southern Enterprises Sofia HZ103600TX User manual

Page |
1
PO#:
HZ103600TX
Sofia Bar Cabinet
Assembly Instructions
For assistance with assembly, contact:
Southern Enterprises Inc.
Customer Service: 1-800-633-5096
[email protected]om
www.seidal.com

Page |
2
1) Quantity
of 1
Top Panel
2) Quantity
of 1
Left Side Panel
3) Quantity
of 1
Right Side Panel
4) Quantity
of 1
Bottom Panel
5) Quantity
of 1
Upper Back Panel
6) Quantity
of 1
Lower Shelf Panel
7) Quantity
of 2
Middle Panels
8) Quantity
of 2
Shelf Panels
9) Quantity
of 8
Article Wine Racks
10) Quantity
of 2
Side Small Middle Panels
11) Quantity
of 3
Small Middle Panels
12) Quantity
of 1
Lower Back Panel
Sofia Bar Cabinet
Parts List
Please review all parts and hardware before disposing of any packaging. Before beginning assembly, separate each
type of hardware. Carefully study the diagrams below and check that you have all parts indicated. Call Customer
Service if missing hardware. Using the incorrect hardware will cause damage.

Page |
3
13) Quantity
of 2
Wood Connect Bars
14) Quantity
of 1
X Wood Connect Bar
15) Quantity
of 2
Leg Frames
16) Quantity
of 1
Left Door
17) Quantity
of 1
Right Door
18) Quantity
of 1
Glass shelf
A) Quantity
of 28
Cam Bolts
B) Quantity
of 28
Cam Locks
C) Quantity
of 22
Cotton Mats
D) Quantity
of 8
Cam Bolts
E) Quantity
of 8
Cam Locks
F) Quantity
of 43
Wood Dowels Dia. 5/16”x1-1/4”L
G) Quantity
of 2
Door Handles
H) Quantity
of 2
Bolts Dia. 5/32’’x 3/4"L
I) Quantity
of 16
Screws Dia. 5/32”x1"L

Page |
4
J) Quantity
of 10
Screws Dia. 1/8”x1/2”L
K) Quantity
of 20
Bolts Dia. 1/4"x1-1/4”L
L) Quantity
of 16
Flat Washers Dia. 1/4”x3/4”
M) Quantity
of 16
Spring Washers Dia. 1/4”
N) Quantity
of 1
Magnet
O) Quantity
of 2
Magnet Plates
P) Quantity
of 2
Screws Dia. 1/8” x 1/2”L
Q) Quantity
of 4
Hinges
R) Quantity
of 24
Screws Dia. 1/8” x 5/8”L
S) Quantity
of 4
Shelf Pins
T) Quantity
of 4
Wood Plugs
U) Quantity
of 1
Allen Wrench
V) Quantity
of 2
Anti-Tipping Hardware
W) Quantity
of 1
Cam Tool
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Periodically apply furniture wax to renew the
finish. Avoid rubbing or scratching the surface
with rough or abrasive objects.
For replacement parts or questions, please call
Customer Service at 1-800-633-5096.
Assembly Tool Required:
No.2 Phillips Screwdriver
(Not Included)

Page |
5
Figure 1
Start with fingers to help align screws
before using screwdriver.
Use Screws (I) and Wood Dowels (F) to
attach Article Wine Racks (9) to Top Panel
(1) and both Shelf Panels (8).
Tighten screws with Phillips screwdriver.
Figure 2
Start with fingers to help align cam bolts
before using screwdriver.
Insert Cam Locks (B) into holes on Middle
Panels (7).
Screw Cam Bolts (A) into threaded holes on
Lower Shelf Panel (6).
Attach Lower Shelf Panel (6) to Middle
Panels (7) using Cam Bolts (A) and Wood
Dowels (F).
Tighten by rotating Cam Locks (B) clockwise
using Phillips screwdriver or Cam Tool (W).
Cover Cam Locks (B) with Cotton Mats (C).
Sofia Bar Cabinet
Assembly Instructions

Page |
6
Figure 3
Insert Cam Locks (B) into holes on Upper
Back Panel (5).
Screw Cam Bolts (A) into threaded holes on
Lower Shelf Panel (6).
Attach Upper Back Panel (5) to Lower Shelf
Panel (6) using Cam Bolts (A).
Tighten by rotating Cam Locks (B) clockwise
with Phillips screwdriver or Cam Tool (W).
Attach both Shelf Panels (8) to Middle
Panels (7) using Wood Dowels (F).
Figure 4
Insert Cam Locks (B) into holes on
assembled unit from Figure 3.
Screw Cam Bolts (A) into threaded holes on
Left Side Panel (2) and Right Side Panel (3).
Attach Left Side Panel (2) and Right Side
Panel (3) to assembled unit from Figure 3
using Cam Bolts (A) and Wood Dowels (F).
Tighten by rotating Cam Locks (B) clockwise
with Phillips screwdriver or Cam Tool (W).

Page |
7
Figure 5
Insert Cam Locks (B) into holes on Left Side
Panel (2) and Right Side Panel (3).
Insert Small Cam Locks (E) into Side Small
Middle Panels (10).
Screw Cam Bolts (A) into 4 corners of
Bottom Panel (4).
Screw Small Cam Bolts (D) and Wood
Dowels (F) into remaining holes on Bottom
Panel (4) and Lower Shelf Panel (6).
Attach unit from Figure 4 to Side Small
Middle Panels (10), Small Middle Panels
(11), and Bottom Panel (4) using both Cam
Bolts (A & D) and Wood Dowels (F).
Tighten by rotating Cam Locks (B/E)
clockwise with Phillips screwdriver or Cam
Tool (W). Cover Cam Locks (B/E) with
Cotton Mats (C).
Figure 6
Insert Cam Locks (B) into holes on
assembled unit from Figure 5.
Screw Cam Bolts (A) into threaded holes on
Top Panel (1).
Attach Top Panel (1) to assembled unit using
Cam Bolts (A) and Wood Dowels (F).
Tighten by rotating Cam Locks (B) clockwise
with Phillips screwdriver or Cam Tool (W).
Cover Cam Locks (B) with Cotton Mat (C).

Page |
8
Figure 7
Use Screws (J) to attach Lower Back Panel
(12) to unit.
Tighten screws with Phillips screwdriver.
Figure 8
Attach Wood Connect Bars (13) and X Wood
Connect Bar (14) to Leg Frames (15) with
Bolts (K).
Tighten bolts with Allen Wrench (U).
Cover Cam Locks (B) with Wood Plugs (T).

Page |
9
Figure 9
Connect assembled units from Figure 7 and
Figure 8 using Bolts (K), Flat Washers (L),
and Spring Washers (M).
Tighten bolts with Allen Wrench (U).
Figure 10
Attach Left Door (16) and Right Door (17) to
assembled unit using Hinges (Q) and
Screws (R).
Attach Magnet (N) to assembled unit using
Screws (J).
Attach Magnet Plates (O) to inside of door
panels using Screws (P).
Tighten screws with Phillips screwdriver.
Attach Door Handles (G) to doors using
Bolts (H).
Tighten bolts with Phillips screwdriver.

Page |
10
Figure 11
Insert Shelf Pins (S) into pre-drilled holes on
middle panels.
Insert adjustable Glass Shelf (18) in
direction of arrow. Make sure shelf pins
stably hold adjustable glass shelf.
Figure 12
Attach Brackets (V) to Back Panel using
Screws (V). Tighten screws with Phillips
screwdriver.
Mark two desired locations on wall, same
distance as Brackets (V) on back of unit. Drill
two 3/16" holes on wall. Insert Plastic
Anchors (V) into holes on wall. (Use hammer
to help.)
Attach Brackets (V) to wall using Screws (V).
Tighten using Phillips screwdriver.
Move this item close to wall Brackets (V) and
tie in both Brackets (V) with Plastic Straps
(V) as shown.
Anti-tipping hardware must be
used for this product to avoid
tipping and injury.