Southern Enterprises CM862200TX User manual

PO#:
Page 1
CM862200TX
Hendrik Apothecary Console
Cabinet
Assembly Instructions

1 Quantity
of 1
Top Panel
2 Quantity
of 1
Left Side Panel
3 Quantity
of 1
Right Side Panel
4 Quantity
of 1
Back Panel
5 Quantity
of 1
Front Panel
6 Quantity
of 2
Middle Panel
7 Quantity
of 1
Bottom Panel
8 Quantity
of 1
Left Drawer Front
9 Quantity
of 1
Middle Drawer Front
10 Quantity
of 1
Right Drawer Front
11 Quantity
of 3
Left Drawer Side Panel
12 Quantity
of 3
Right Drawer Side Panel
Page 2
Hendrik Apothecary Console
Parts List
Please check packaging for all parts and hardware before discarding. Unpack and lay parts on clean, padded
surface like carpet or blanket. Check that you have all parts indicated. Call customer service if hardware is
missing. Before beginning assembly, carefully study the diagrams below and sort your hardware according to the
pictures. Using the incorrect hardware will cause damage.

13 Quantity
of 3
Drawer Back Panel
14 Quantity
of 3
Drawer Bottom Panel
A Quantity
of 23
Cam Bolt
B Quantity
of 23
Cam Lock
C Quantity
o f 11
Bolt Dia. 1/4x1-1/4” L
D Quantity
o f 4
Spring Washer Dia. 1/4”
E Quantity
o f 4
Flat Washer Dia. 1/4”x3/4”
F Quantity
o f 1
Allen Wrench
G Quantity
of 24
Screw Dia. 5/32” x 1L
H Quantity
of 6
Knob
I Quantity
o f 12
Bolts Dia. 5/32” x 1-1/8”L
J Quantity
of 2
Anti-tipping hardware
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Periodically apply furniture wax to renew
the finish. Avoid rubbing or scratching the
surface with rough or abrasive objects.
For replacement parts or questions, please
call Customer Service at 1-800-633-5096.
Page 3
Assembly Tool Required
No.2 Phillips Screwdriver
(Not Included)

Figure 1
Start with finger to help align Cam Bolts
before using screwdriver.
Insert Cam Locks (B) into corresponding
holes on Middle Panel (6).
Screw Cam Bolts (A) into threaded holes
on Back Panel (4) and Front Panel (5).
Attach Back Panel (4) and Front Panel
(5) to Middle Panel (6) by inserting Cam
Bolts (A) into corresponding holes until
all panels meet.
Tighten Cam Bolts (A) by rotating Cam
Locks (B) clockwise using Phillips
screwdriver.
Figure 2
Insert Cam Locks (B) into corresponding
holes on Back Panel (4).
Screw Cam Bolts (A) into threaded holes on
Left Side Panel (2) and Right Side Panel (3).
Attach Left Side Panel (2) and Right Side
Panel (3) to Back Panel (4) by inserting Cam
Bolts (A) into corresponding holes until all
panels meet.
Tighten Cam Bolts (A) by rotating Cam
Locks (B) clockwise using Phillips
screwdriver.
Use Bolts (C) to connect Side Panels (2/3)
to Front Frame (5).
Use Bolts (C) with Flat Washers (E) and
Spring Washers (D) to connect Side Panels
(2/3) to Bottom (7).
Tighten Bolts (C) with Allen Wrench (8).
Page 4
Hendrik Apothecary Console
Assembly Instructions

Figure 3
Insert Cam Locks (B) into corresponding
holes on Left Side Panel (2), Right Side
Panel (3), Middle Panel (6) and Back
Panel (4).
Screw Cam Bolts (A) into threaded holes
on Top Panel (1).
Attach Top Panel (1) to Left Side Panel
(2), Right Side Panel (3), Middle Panel
(6) and Back Panel (4) by inserting Cam
Bolts (A) into corresponding holes until
all panels meet.
Tighten Cam Bolts (A) by rotating Cam
Locks (B) clockwise using Phillips
screwdriver.
Use Bolts (C) to connect Top Panel (1) to
Front Frame (5).
Tighten Bolts (C) using Allen Wrench
(F)
.
Figure 4
Start with finger to help align Screws.
Attach Drawer Side Panels (11/12) to
Drawer Back Panel (13) using Screws
(G).
Tighten Screws (G) with Phillips
screwdriver.
Insert Drawer Bottom Panel (14) into the
grooves of Panels (11/12/13).
Attach Drawer Front Panel (9) to the
assembled unit using Screws (G).
Finally, attach Knobs (H) to the Drawer
Front Panel (9) using Bolts (I).
Tighten Bolts (I) with Phillips screwdriver.
Repeat step for additional drawers using
Drawer Front Panels (8/10).

Page 5
Page 6
Figure 4
Insert drawers into assembled unit as
shown.
Make sure all slides glide smoothly in
and out.
Figure 5
Attach Brackets (J) to back panel using
Screws (J).
Tighten Screws (J) using Philips screwdriver.
Mark two desired locations in the same
distance as the Brackets (7) located on the
back of the unit onto the wall and drill two
3/16" holes for each Bracket (J).
Insert Plastic Anchors (J) into the holes for
each Bracket (J) on wall as shown. Use a
hammer to insert plastic anchors until they
are flush with wall.
Then, attach Brackets (J) onto wall using
Screws (J).
Tighten Screws (J) using Philips screwdriver.
Move this item close to the wall Brackets (J)
and tie in all Brackets (J) together with
Plastic Straps (J) as shown in diagram.
Anti-tipping hardware must be used for
this product to avoid tipping and injury.

Page 7
Figure 7
Now your Hendrik apothecary console
is ready to use.

Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/Website/Catalog
Please indicate color/size/style number:
Style No Parts Letter Parts Description Quantity Needed
Please immediately examine this product carefully. Any request for missing parts or damage replacement must be received within 90
days of your receipt of the product. Replacement, if available, will be honored within this time frame.Parts will not be available for items
arriving fully assembled. We do not recommend modifying product(s) and we are not responsible for any damages due to product
modification(s). If damages or missing parts are not reported within 90 days of your receipt, we are under no obligation to provide parts or
replacement merchandise.
For product issues, please contact Southern Enterprises at 800-633-5096 (toll-free) / 972-869-0111 (Dallas) Mon-Fri 9am – 4pm CST, or
email us at [email protected]. Please ask for customer service representative for issues involving damages or replacement parts.
Please ask for technical assistance representative for any issues with product and assembly/construction.
Please contact the retailer that you purchased from for returns.
Page 8
Parts Replacement Form
Customer Service: 1-800-633-5096
[email protected]om
Southern Enterprises, Inc.
600 Freeport Parkway, Suite 200
Coppell, Texas 75019