Southern Enterprises HZ8864A0TX User manual

Page | 1
PO: 13588
Each shelf supports up to lb.
HZ8864A0TX / HZ8864B0TX
Metal/Glass Sliding-Door Display
Cabinet
Assembly Instructions
For assistance with assembly, contact:
Southern Enterprises Inc.
Customer Service: 1-800-633-5096
[email protected]om
www.seidal.com

Page | 2
1) 2PCS
Legs
2) 1PC
Stretcher
3) 1PC
Bottom Frame
4) 1PC
Left Rear Support
5) 1PC
Right Rear Support
6) 1PC
Left Front Support
7) 1PC
Right Front Support
8) 1PC
Top Frame
9) 1PC
Glass Back Panel
10) 2PCS
Glass Side Panels
11) 3PCS
Glass Shelves
12) 2PCS
Glass Doors
Metal/Glass Sliding-Door Display Cabinet
Parts List
Please review all parts and hardware before disposing of any packaging. Before beginning assembly, separate each type
of hardware. Carefully study the diagrams below and check that you have all parts indicated. Call Customer Service if
missing hardware. Using incorrect hardware will cause damage. You may receive extra hardware with your unit.

Page | 3
A) 16PCS
Bolts 1/4”x3/4”
B) 16PCS
Spring Washers
C) 16PCS
Flat Washers
D) 12PCS
Glass Pads
E) 4PCS
L Metal Chips
F) 2PCS
Plastic Straps
G) 2PCS
Screws 4x16mm
H) 4PCS
Bolts 1/4”x1-1/2”
I) 4PCS
Sliding Wheels
J) 2PCS
Plastic Anchors
K) 2PCS
Screws 4x38mm
L) 4PCS
Pads
**Pre-attached to glass doors**
M) 1PC
Wrench
Assembly Tool Required:
No.2 Phillips Screwdriver
(Not Included)
For replacement parts or questions, please c all
Customer Service at 1-800-633-5096.
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Avoid rubbing or scratching the surface with
rough or abrasive objects.

Page | 4
Figure 1
Note: Do not fully tighten bolts
until Step 6 is complete.
Step 1:
Unit assembly should begin
with parts turned upside down
for Step 1.
Attach Legs (1) to Stretcher (2)
using Bolts (A), Spring Washers
(B), and Flat Washers (C).
Figure 2
Step 2:
Attach assembled parts to
Bottom Frame (3) using Bolts (A),
Spring Washers (B) and Flat
Washers (C).
Figure 3
Step 3
Attach Left Rear Support (4),
Right Rear Support (5), Left Front
Support (6), and Right Front
Support (7) to Bottom Frame (3)
using Bolts (H), Spring Washers
(B) and Flat Washers (C).
Metal/Glass Sliding-Door Display Cabinet
Assembly Instructions

Page | 5
Figure 4
Step 4
Insert Glass Back Panel (9) along
grooves of Left Rear Support (4)
and Right Rear Support (5).
Figure 5
Step 5
Insert Glass Side Panels (10)
along the grooves of Left Rear
Support (4), Right Rear Support
(5), Left Front Support (6) and
Right Front Support (7).
Figure 6
Step 6
Attach Top Frame (8) to Left Rear
Support (4), Right Rear Support
(5), Left Front Support (6) and
Right Front Support (7) using
Bolts (A).

Page | 6
Figure 7
Step 7
Turn assembled unit upright.
Stick Glass Pads (D) to brackets on
Left Rear Support (4), Right Rear
Support (5), Left Front Support (6)
and Right Front Support (7).
Place Glass Shelves (11) onto
brackets of each Support (4/5/6/7).
Figure 8
Step 8
Attach Sliding Wheels (I) to
pre-attached Pads (L) on Glass
Doors (12).
Figure 9
Step 9
Insert Glass Doors (12) into grooves
of Top Frame (8) and Bottom Frame
(3).
Note: In order to insert doors into
grooves, insert top of door first,
then insert bottom of door into
bottom groove.
8
3
I
I
I
7
5
6
4

Page | 7
Figure 10
Anti-tipping Hardware
Tip: At least one screw must be
directly mounted into a wall stud.
Wall anchor is not needed when
mounting into a wall stud.
Find ideal location on wall and mark
location of each mounting hole.
Using a power drill and a 3/16″drill
bit, drill one 3/16″hole on wall.
Note: Make sure not to drill into
electrical wiring or plumbing
pipes.
Insert Wall Anchor (J) into 3/16″hole.
Make sure that wall anchors are flush
with wall.
Tip: It may be necessary to use a
hammer to gently tap anchors into
place.
Attach L Metal Chips (E) in pre-drilled
holes on back of Left Rear Support
(4) and Right Rear Support (5) using
Screws (G).
Attach L Metal Chip (E) to Wall
Anchor (J) using Screws (K) and
Phillips Screwdriver.
Attach Plastic Straps (F) to L Metal
Chips (E) on wall and Tower.
Now your Metal/Glass Sliding-Door
Display Cabinet is ready to use!
Screw (K)
(E)
(J)

Page | 8
Please immediately examine this product carefully. Any request for missing parts or damage replacement must be
received within 90 days of your receipt of the product. Replacement, if available, will be honored within this time frame.
Parts will not be available for items arriving fully assembled. We do not recommend modifying product(s) and we are not
responsible for any damages due to product modification(s). If damages or missing parts are not reported within 90 days
of your receipt, we are under no obligation to provide parts or replacement merchandise.
For product issues, please contact Southern Enterprises at 800-633-5096 (toll-free) / 972-869-0111 (Dallas), Mon-Fri
9am – 4pm CST, or email us at [email protected]m. Please ask for customer service representative for issues
involving damages or replacement parts. Please ask for technical assistance representative for any issues with product
and assembly/construction.
Please contact the retailer that you purchased from for returns.
Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/Website/Catalog
Please indicate color/size/style number:
Style No Parts Letter Parts Description Quantity Needed
Parts Replacement Form
Customer Service: 1-800-633-5096
[email protected]om
Southern Enterprises, Inc.
600 Freeport Parkway, Suite 200
Coppell, Texas 75019