Southern Enterprises HE408000TX User manual

HE408000TX
Mission Hall Tree Bench
Assembly Instruction
For assistance with assembly,
contact:
Southern Enterprises Inc.
Customer Service 1-800-633-5096
[email protected]
www.seidal.com
PO#13112
250lb Max Seat Load
Page 1

HE408000TX
Mission Hall Tree Bench
Parts List
Please check packaging for all parts and hardware before discarding. Unpack and lay parts on
clean, padded surface like carpet or blanket. Check that you have all parts indicated. Call customer
service if hardware is missing. Before beginning assembly, carefully study the diagrams below and sort
your hardware according to the pictures. Using the incorrect hardware will cause damage.
A
Top Panel
B
Back Panel
C
Wooden Support Panel
D
Seat Panel
E
Left Side Panel
F
Front Top Stretcher
G
Back Top Stretcher
H
Bottom Stretcher
I
Right Side Panel
1
Cam Bolt ∮1/4”x1-1/2”
2
Cam Lock ∮5/8”x1/2”
3
Bolt ∮1/4” x1”
4
Bolts∮1/4”x 1-1/2”
5
T-Nut
∮1/4”
6
Allen Wrench
7
Hanger
8
Screw ∮1/8”x1/2”
9
Dowel 1/4 x1-1/4”
Quantity
Of 1 Quantity Of 1 Quantity
Of 4
Quantity
Of 1
Quantity
Of 2
Quantity
Of 1 Quantity
Of 1
Quantity
Of 1 Quantity
Of 2
Quantity
Of 1
Quantity
Of 19 Quantity
Of 19 Quantity Of 12
Quantity
Of 3 Quantity
Of 3
Quantity
Of 1
Quantity
Of 4
Quantity
Of 8 Quantity
Of 2
Page 2

Tool List: 3/16" drill bit, drill, tape measure and pencil.
10
Screw ∮5/32”x1”
11
Adhesive Pad
12
Dowel 5/16” x1-1/4”
13
Plastic Anchor
14
Screw∮5/32”x1-1/2”
15
Bolts∮1/4”x 1-1/4”
16
Spring Washer Dia.1/4”
17
Flat washer Dia.1/4” x3/4”
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Periodically apply furniture wax to renew the
finish. Avoid rubbing or scratching the
surface with rough or abrasive objects.
Call customer service at 1-800-633-5096
for assistance, questions, or Parts.
Assembly Tool Required
No.2 Phillips Screw Driver
Quantity
Of 3 Quantity Of 8
Quantity
Of 2
Quantity
Of 2 Quantity Of 2 Quantity Of 2
Quantity
Of
2
Quantity
Of
2
Page 3

HE408000
TX
Mission Hall Tree Bench
Assembly Instruction
Figure 1
Attach Wooden Support Panel
(C) to Back Panel (B) using
Bolts (3) as shown.
Tighten Bolts with Allen
Wrench (6).
Note: Make sure to
insert the bolts all the
way into the recessed
hole until it comes out
the other side of Panel
(B).
Figure 2
Attach Top Panel (A) to the top
of Back Panel (B) using
Dowels (9), Bolts (3) and
Screws (10).
Tighten Bolts with Allen
Wrench (6).
Tighten screw with Phillips
screwdriver.
Page 4

Figure 3
Attach Seat Panel (D) to the
bottom of Back Panel (B)
using Bolts (4) and T-Nuts (5).
Insert Bolts (3) through Seat
Panel (D) and into Wooden
Support Panels (C) as shown.
Tighten bolts with Allen
Wrench (6).
Note: Bolts (4) have to be
inserted into the T-Nuts
threaded hole and
tightened.
Please do not over-tighten cam bolts.
Please stop when you feel tight.
Figure 4
Insert Cam Locks (2) into
corresponding holes on Back
Top Stretcher (G) and Bottom
Stretcher (H).
Screw Cam Bolts (A) into the
threaded holes on Side Panels
(E/I).
Attach Side Panels (E/I) to
Back Top Stretcher (G) and
Bottom Stretchers (H) by
inserting Wood Dowels (12)
and Cam Bolts (1) into
corresponding holes until Side
Panels (E/I), Top Stretcher (G)
and Bottom Stretchers (H)
meet.
Tighten by rotating Cam Locks
(2) clockwise with Phillips
screwdriver.
Attach Front Top Stretcher (F)
to the assembled unit with
Bolts (15), Spring Washers
(16) and Flat Washers (17) as
shown.
Tighten Bolts (15) with Allen
Wrench (F).
Stick Adhesive Pads (11) onto
Cam Locks (2).

Figure 5
Insert Cam Locks (2) into
holes on the assembled unit
from Figure 4.
Screw Cam Bolts (1) into the
threaded holes on the
assembled unit from Figure 3.
Attach the assembled unit
from Figure 4 to the
assembled unit from Figure 3
by inserting Cam Bolts (1) into
corresponding holes until the
assembled units meet.
Tighten by rotating Cam Locks
(2) clockwise with Phillips
screwdriver.
Figure 6
Drill two 3/16" holes on the
wall with measurements as
shown.
Insert Plastic Anchors (13) into
the holes of wall as shown.
(When doing this, you will
need a hammer help you).
Using the Phillips head
screwdriver, install Screws
(14) into each of the Anchors
(13) as shown.
Page 6

Parts Replacement Form
Figure 7
Attach Hangers (7) to hall tree
bench by using Screws (8) as
shown.
Tighten screw with Phillips
screwdriver.
Page 7

Please immediately examine this product carefully. Any request for missing parts or damage replacement
must be received within 90 days of your receipt of the product. Replacement, if available, will be honored
within this time frame.Parts will not be available for items arriving fully assembled. We do not recommend
modifying product(s) and we are not responsible for any damages due to product modification(s). If
damages or missing parts are not reported within 90 days of your receipt, we are under no obligation to
provide parts or replacement merchandise.
Please contact Southern Enterprises at 800-633-5096 or in Dallas 972-869-0111/ 9am – 4pm Mon-Fri
Central time if you have product issues or email us at [e-mail]. Please ask for customer service
representative for issues involving damages or replacement parts. Please ask for technical assistance
representative for any issues with product and assembly/construction.
Please contact the retailer that you purchased from for returns.
Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/Website/Catalog
Please indicate color/size/style number:
Style No Parts Letter Parts Description Quantity Needed
Parts Replacement Form
Customer Service 1-800-633-5096
[e-mail]
Southern Enterprises, Inc.
600 Freeport Parkway, Suite 200
Coppell
, Texas
75019
Page 8