Southern Enterprises MS040700TX User manual

Page |
1
PO#:
MS040700TX
Blankenship Media Console
Assembly Instructions
For assistance with assembly, contact:
Southern Enterprises, Inc.
Customer Service: 1-800-633-5096
[email protected]om
www.seifurniturestore
.com

Page |
2
1) Quantity
of 1
Top Panel
2) Quantity
of 1
Left Side Panel
3) Quantity
of 1
Right Side Panel
4) Quantity
of 1
Shelf Panel
5) Quantity
of 1
Middle Panel
6)Quantity
of 1
Bottom Panel
7) Quantity
of 1
Back Panel
8) Quantity
of 2
Drawer Front Panel
9) Quantity
of 2
Drawer Left Side Panel
10) Quantity
of 2
Drawer Right Side Panel
11) Quantity
of 2
Drawer Back Panel
12) Quantity
of 2
Drawer Bottom Panel
Blankenship Media Console
Parts List
Please check packaging for all parts and hardware before discarding. Unpack and lay parts on clean, padded
surface like carpet or a blanket. Check that you have all parts indicated. Call customer service if any hardware is
missing. Before beginning assembly, carefully study the diagrams below and sort your hardware according to the
pictures. Using the incorrect hardware will cause damage.

Page |
3
13) Quantity
of 4
Leg
A) Quantity
of 16
Cam Bolts
B) Quantity
of 16
Cam Locks
C) Quantity
of 16
Wood Dowels Dia. 5/16"x1-1/4"
D)Quantity
o f 12
Bolt Dia. 1/4x3/4” L
E)Quantity
o f 12
Spring Washer Dia.1/4”
F)Quantity
o f 12
Flat washer Dia.1/4” x3/4”
G) Quantity
of 1
Allen Wrench
H ) Quantity
of 20
Screw Dia. 1/8” x 5/8”L
I) Quantity
of 8
Cam Bolts
J) Quantity
of 8
Cam Locks
K) Quantity
of 8
Screw
Dia. 5/32”x 1L
L) Quantity
of 2
Plastic Strap

Page |
4
M) Quantity
of 4
Bracket
N) Quantity
of 2
Screws Dia. 1/8”x1-1/2”L
O) Quantity
of 2
Screws Dia. 1/8”x5/8”L
P) Quantity
of 2
Anchor
Q) Quantity
of 14
Adhesive Pad
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Periodically apply furniture wax to renew the
finish. Avoid rubbing or scratching the surface
with rough or abrasive objects.
For replacement parts or questions, please call
SEI Customer Service at 1-800-633-5096.
Assembly Tool Required:
No.2 Phillips Screwdriver, Hammer
(Not Included)

Page |
5
Figure 1
Align Bolts (D) by hand.
Attach Legs (13) to the Bottom Panel (6)
with Bolts (D), Spring Washers (E), and
Flat Washers (F).
Tighten Bolts (D) with Allen Wrench (G).
Figure 2
Attach the Shelf Panel (4) to the Middle
Panel (5).
Blankenship Media Console
Assembly Instructions
D
E
F
G
13
13
4
5

Page |
6
Please do not overtighten cam locks. Stop when they feel
secure.
Figure 3
Align Cam Bolts (A) by hand.
Insert Cam Locks (B) into corresponding
holes on Shelf Panel (4).
Screw Cam Bolts (A) into threaded holes
on Side Panels (2/3).
Attach Side Panels (2/3) to Shelf Panel (4)
by inserting Cam Bolts (A) and Wood
Dowels (C) into corresponding holes until
all panels meet.
Tighten Cam Bolts (A) by rotating Cam
Locks (B) clockwise using Phillips
screwdriver (not included).
Figure 4
Align Cam Bolts (A) by hand.
Insert Cam Locks (B) into corresponding
holes on Side Panels (2/3) & Middle Panel
(5).
Screw Cam Bolts (A) into threaded holes
on Bottom Panel (6).
Attach Bottom Panel (6) to Side Panels
(2/3) & Middle Panel (5) by inserting Cam
Bolts (A) and Wood Dowels (C) into
corresponding holes until all panels meet.
Tighten Cam Bolts (A) by rotating Cam
Locks (B) clockwise using Phillips
screwdriver (not included).
Cover Cam Locks (B) with Cotton Mats
(Q) provided.
2
3
B
AC
6
A
C
QB
4

Page |
7
Figure 5
Start with finger to help align Cam Bolts.
Insert Cam Locks (B) into corresponding
holes on Side Panel (2/3) & Middle Panel
(5).
Screw Cam Bolts (A) into threaded holes
on Top Panel (1).
Attach Top Panel (1) to Side Panel (2/3) &
Middle Panel (5) by inserting Cam Bolts
(A) and Wood Dowel (C) into
corresponding holes until all panels meet.
Tighten Cam Bolts (A) by rotating Cam
Locks (B) clockwise using Phillips
screwdriver.
Cover Cam Locks (B) with Adhesive Pads
(Q).
Figure 6
Attach Back Panels (7) to back of the unit
with Screws (H).
Tighten Screws (H) with Phillips
screwdriver (not included) .
C
1
B
A
C
Q

Page |
8
Figure 7
Attach Drawer Side Panels (9/10) to
Drawer Front Panel (8) using Cam Bolts (I)
and Cam Locks (J).
Cover Cam Locks (J) with Adhesive Pads
(Q).
Attach Drawer Back Panel (11) to Side
Panels (9/10) using Screws (K).
Insert Drawer Bottom Panel (12) into
grooves of Panels (9/10/11).
Repeat this step for additional drawers.
Figure 8
Insert assembled drawers into assembled
unit from Figure 6.
Make sure drawers glide smoothly in and
out.
Note: There is a lever located on male
slide for bottom drawer slide. Push
lever to either side in order to detach
male slide from female slide.
Note: If drawer heights are off, loosen
screws on male slide to adjust height of
drawer(s).
JQ
8
9
10
I
K

Page |
9
Figure 9
Attach Brackets (M) to Back Panel using
Screws (O).
Tighten Screws (O) using a Philips
screwdriver (not included).
Mark two desired locations on wall.
Drill two 3/16" holes.
Insert Plastic Anchors (P) into the holes,
tap lightly with hammer (not included) as
needed.
Attach Brackets (M) to wall using Screws
(N).
Tighten Screws (N) using a Philips
screwdriver (not included).
Figure 10
Move the media stand close to the wall.
Tie Brackets (M) together with Plastic
Straps (L).
Warning: Anti-tipping hardware must
be used for this product to avoid
tipping and injury.

Page |
10
Figure 11
Now your Blankenship Media Console is
ready to use!

Page |
11
CAUTION
The top shelf of this cabinet is intended for plasma/LCD televisions. Max TV size is 50" flat screen and Max
weight limit is 85 lb.
The top shelf is NOT INTENDED for tube televisions.
Each shelf should not be loaded with more than 20 lb. Each drawer should not be loaded with more than 15 lb.
DO NOT EXCEED RECOMMENDED LOAD. Use with products heavier than the maximum sizes and weights
indicated may result in instability causing possible injury.
This unit contains a permanent warning sticker located on back panel.
Do not allow children under 16 years to move the media stand.
Model: MS040700 TX
Blankenship Media Console
Southern Enterprises, Inc
600 Freeport Parkway, Suite 200
Coppell, Texas, 75019
Manufacture Date: 11/25/2015

Page |
12
Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/Website/Catalog
Please indicate color/size/style number:
Style No Parts Letter Parts Description Quantity Needed
Please immediately examine this product carefully. Any request for missing parts or damage replacement must be
received within 90 days of your receipt of the product. Replacement, if available, will be honored within this time
frame.Parts will not be available for items arriving fully assembled. We do not recommend modifying product(s)
and we are not responsible for any damages due to product modification(s). If damages or missing parts are not
reported within 90 days of your receipt, we are under no obligation to provide parts or replacement merchandise.
For product issues, please contact Southern Enterprises at 800-633-5096 (toll-free) / 972-869-0111 (Dallas),
Mon-Fri 9am – 4pm CST, or email us at [e-mail]. Please ask for customer service representative for
issues involving damages or replacement parts. Please ask for technical assistance representative for any issues
with product and assembly/construction.
Please contact the retailer that you purchased from for returns.
Parts Replacement Form
Customer Service: 1-800-633-5096
[email protected]
Southern Enterprises, Inc.
600 Freeport Parkway, Suite 200
Coppell, Texas 75019