Speco Intensifier OiD4 User manual

Intensifier
®
HD Megapi
Vandal Resistant Dome IP Camera
OiD4
HD Megapi
xel Indoor/Outdoor
Vandal Resistant Dome IP Camera
xel Indoor/Outdoor
Vandal Resistant Dome IP Camera

O
Oi iD D4 4 U Us se er r’ ’s s G Gu ui id de e
Rev.1.0.2 (Jul. 2014) 2
Caution
Any changes or modifications in construction of this device which are not explicitly approved by the
party responsible for compliance could void the user’s warranty.
Note
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generate, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into and outlet on a circuit different from that to which the receiver is
connected
Consult the dealer or an experienced radio/TV technician for help.
Directions
Be careful not to cause any physical damage by dropping or throwing the camera. Especially keep the
device out of reach from children.
Do not disassemble the camera. No after service is assumed when disassembled.
Use only power adapters compatible with the unit.
Be careful to prevent moisture or water penetration into the unit. Particular attention is needed when
installing the unit. The screw holes for the installation screws and pipe should be maintained water tight
during the whole life time of the product.
All the electrical connection wires running into the unit should be prepared so that water from the outside
cannot flow into the unit through the surface of the wires. Penetration of the moisture through the wire for
extended period can cause malfunction of the unit or deteriorated image.

O
Oi iD D4 4 U Us se er r’ ’s s G Gu ui id de e
Rev.1.0.2 (Jul. 2014) 3
Revision History
Date Revision Details
Jun 1
st
, 2014 1.0 First manual revision creation.
Jul 9
th
, 2014 1.0.1 Minor revisions
Jul 11
th
, 2014 1.0.2 Minor revisions

O
Oi iD D4 4 U Us se er r’ ’s s G Gu ui id de e
Rev.1.0.2 (Jul. 2014) 4
Contents
1. Introduction .................................................................................................................................................... 5
1.1. Overview ............................................................................................................................................... 5
1.2. Specifications ........................................................................................................................................ 6
1.3. Applications of OiD4 ............................................................................................................................. 8
2. Product Description ...................................................................................................................................... 9
2.1. Contents................................................................................................................................................ 9
2.2. Product Preview.................................................................................................................................... 9
2.3. Physical description ............................................................................................................................10
2.3.1. External View............................................................................................................................10
2.3.2. Dimensions ...............................................................................................................................10
2.3.3. External Connector ................................................................................................................... 11
2.3.4. Factory Default Switch.............................................................................................................. 11
2.4. Functional Description ........................................................................................................................12
3. On Site Installation ......................................................................................................................................14
4. Getting Started.............................................................................................................................................15
4.1. PC Requirement .................................................................................................................................15
4.2. Quick Installation Guide ...................................................................................................................... 16
4.2.1. Connect PC and OiD4 to network. ...........................................................................................16
4.2.2. Install Speco-NVR and set IP parameters on OiD4 .................................................................16
4.2.3. Remote video connection to OiD4............................................................................................18
4.2.4. Additional settings through connection to the Admin Page ......................................................20
5. Trouble Shooting .........................................................................................................................................21
5.1. No power is applied ............................................................................................................................21
5.2. Cannot connect to the Video...............................................................................................................22
5.3. Windows Vista or Windows 7..............................................................................................................23
5.4. Technical Assistance...........................................................................................................................26
Appendix A– Important Notice in Exchanging SD Card (Micro SD).........................................................................27

O
Oi iD D4 4 U Us se er r’ ’s s G Gu ui id de e
Rev.1.0.2 (Jul. 2014) 5
1. Introduction
1.1. Overview
The ONSIP OiD4 is a state-of-the-art mega-pixel, dual-codec (H.264, MJPEG) IP/network camera built with
embedded software and hardware technology. It enables real time transmission of synchronized video of HD
resolution and audio data. Remote clients can connect to ONSIP OiD4 for the real time video/audio data
through various client solutions running on PC, PDA or mobile phones. Real time 2-way communication is
available through bidirectional audio communication feature.
Intensifier® technology is the most optimized solution for indoor and outdoor surveillance in low-light conditions
by using superior CMOS sensor with low-light sensitivity ISP sensor. Intensifier® is especially beneficial in poor
lighting environments, efficiently reducing noise and ghosting while maintain a color image without the use of IR
LEDs.
Designed to be a stand-alone streaming audio & video transmission device, ONSIP OiD4 can be applied to
various application area such as video security, remote video monitoring, distance education, video conference
or internet broadcasting system.
IP66 compliant housing will extend the application area to harsh environments of wide temperature range.
Embedded PoE (Power over Ethernet, IEEE 802.3af) will enable the owner to reduce TCO (Total Cost of
Ownership) by reducing on-site wiring works for the installation.

O
Oi iD D4 4 U Us se er r’ ’s s G Gu ui id de e
Rev.1.0.2 (Jul. 2014) 6
1.2. Specifications
Camera
Image sensor Progressive scan 1/3 inch CMOS 1.3M pixels
Full resolution 1,280 x 720 pixels (HD)
Min. illumination Color : 0.0005 Lux (F1.2)
Sync System Internal
S/N Ratio 62dB or more
Lens 3.6~16mm
Day & Night AWB
Sensitivity
(F1.2, 30 IRE , ICR B/W)
Intensifier OFF - 0.12 Lux
Intensifier Max – 0.0005 Lux
Back Light Compensation ON / OFF
White Balance ATW(2.000 K ~ 10,000 K) / MANUAL / PUSH
Exposure DC / ESC
WDR ON - 15 Frames / OFF - 30 Frames
3D-DNR DAY : 0~20, NIGHT : 0~20
Intensifier AUTO ON (Max 128x) / OFF
Privacy Mask ON / OFF (10 Programmable Zones)
Motion Detection ON / OFF (4 Programmable Zones)
Digital Zoom 1x ~ 12x
Mirror H / V / Rotate
DEFOG OFF / AUTO
OSD BUILT IN
Video
Compression method Simultaneous Dual Codec (H.264 / MJPEG)
Resolution 1,280 x 720@60fps
Multi-Profile Streaming - 5 simultaneous video profiles
- Select the codec type, resolution and frame rates for each profile.
Intelligent Bit-Rate Control VBR or CBR
PTZ Digital PTZ & Video crop
Image Setting Text overlay, Privacy mask, De-interlace filter
Motion detection 3 regions

O
Oi iD D4 4 U Us se er r’ ’s s G Gu ui id de e
Rev.1.0.2 (Jul. 2014) 7
Audio
Mono Upstream 32Kbps G.726 ADPCM, 64Kbps 16bit µ-law PCM ~ MIC/Line-in
Mono Downstream 64Kbps 16bit µ-law PCM ~ Line-out
Network
Network Protocol
- IPv4, TCP, UDP, IGMP, ICMP, ARP, RARP, PPPoE, RTCP
- RTP, RTSP, SDP, HTTP, SMTP, FTP, DHCP, UPnP
- NTP, DNS, DynDNS
Dynamic IP Speco DDNS (free of charge)
Security - User ID & Password protection, IP address filtering
- Digest Authentication, User Access Log
Streaming method
- RTSP streaming with proprietary format for control information
- standard RTSP streaming
- HTTP streaming
External Terminals
LAN 10/100BaseT LAN (auto MDIX)
Alarm input / output Alarm I/O (1 Sensor input & 1 Relay output)
Factory Reset Supported
Audio MIC/Line in, Line out
Power DC 12V input
Alternate Power
Standard PoE IEEE802.3af Supported
Alarm & Event
Intelligent Video Motion Detection
Alarm Triggers Intelligent Video + Sensor Input
Alarm Events Video file upload(FTP), Still Image transmission(Email), Relay output
Alarm Buffer (Audio/Video) Configurable Pre-alarm (5~15 sec) & Post-alarm (10~60 sec)
Client Software
Speco NVR Windows XP/Vista/7 (free of charge)
Speco ONSIP Android™, iPhone®, iPad® (free of charge)
Miscellaneous
Operating Temperature -20
°
C ~ 45
°
C (-4
°
F~113
°
F)
Operation Humidity 8~80% RH
Power DC 12V, 0.6A
Dimensions(W x H x D) Ø130mm(5.11”) x 92mm(3.62”)
Weight 1kg (2lbs)
Casing AL, PC, Vandal resistant, IP66
Approvals FCC, RoHS
Package information Unit, CD, mounting screws

O
Oi iD D4 4 U Us se er r’ ’s s G Gu ui id de e
Rev.1.0.2 (Jul. 2014) 8
1.3. Applications of OiD4
Security surveillance (buildings, stores, manufacturing facilities, parking lots, banks, government facilities,
military, etc.)
Remote monitoring (hospitals, kindergartens, traffic, public areas, etc.)
Teleconference (Bi-directional audio conference). Remote Learning, Internet broadcasting
Weather and environmental observation

O
Oi iD D4 4 U Us se er r’ ’s s G Gu ui id de e
2. Product Description
2.1. Contents
The product package
contains followings :
Contents
OiD4
Accessories
CD
Quick Reference Guide
2.2. Product Preview
OiD4
Camera Unit
PC software to allocate an IP
address to the IP Camera
contains followings :
Description
OiD4 main unit
CVBS Cable 1EA,
Screws (3 pieces of 1 type),
Anchors (3 pieces of 1 type),
L-type wrench with six angles 1EA
Software & User’s Guide
Quick installation guide
ONSIP Installer VMS Software
PC software to allocate an IP
address to the IP Camera
PC software to
view and record the
A/V streaming data transmitted from
IP camera.
(Simultaneous support of up to 64
IP cameras@D1)
Remarks
(Speco NVR)
view and record the
A/V streaming data transmitted from
(Simultaneous support of up to 64

O
Oi iD D4 4 U Us se er r’ ’s s G Gu ui id de e
Rev.1.0.2 (Jul. 2014) 10
2.3. Physical description
2.3.1. External View
Figure 2-1. External view of OiD4
2.3.2. Dimensions
Figure 2-2. Dimensions
Unit : mm

O
Oi iD D4 4 U Us se er r’ ’s s G Gu ui id de e
Rev.1.0.2 (Jul. 2014) 11
2.3.3. External Connector
Figure 2-3. Connector for external connection
2.3.4. Factory Default Switch
Factory default switch is provided for returning the IP camera to factory default state. Unscrew the cover to
access the switch. There are two functions assigned to factory default switch.
1. Returning to Factory Default State : Press the switch about 5 seconds while power is applied to
return to factory default state.
2. Safe Removal of Micro-SD Card : Press the switch for 1 second to unmount the Micro SD Card for
safe removal.
Figure 2-4. Factory Default switch and Micro-SD Card slot
Micro SD Card slot
Factory Default Switch
Network (LAN)
Power
Sensor Input (white(+), Red(-))
Relay Output (Black(+), Yellow(-))
Mic/Line Input
Line Output

O
Oi iD D4 4 U Us se er r’ ’s s G Gu ui id de e
2.4. Functional Description
 Power :
Power input for supplying
Caution : If OiD4
is powered by PoE, do not plug in DC Jack with active DC power
into
DC power connector.
 Network (LAN)
100Mbps Ethernet connector (RJ-
45) with PoE standard (802.3af). LED on the Ethernet connector shows
the status of OiD4 as follows:
- Status LED (
It will be lit in green or red depending on the status
① Green :
Green color indicates that the camera is in normal operation mode. Continuous green
indicates that data transmission is possible. Blinking green means that someone is connected to
OiD4.
② Red :
Continuous or blinking red indicates that hardware is in abnormal condition.
 Micro SD Card slot
Please insert SD memory card when you want
card, please push the SD card.
 MIC/Line Input
Connect external audio source or microphone.
 Line Output
Connect speakers with built in amplifier. Audio from remote site is output through Line out
audio mode.
LED will be lit with red momentarily and it will be lit with green after a while when power is
applied into OiD4
Power input for supplying
12V DC power.
is powered by PoE, do not plug in DC Jack with active DC power
DC power connector.
45) with PoE standard (802.3af). LED on the Ethernet connector shows
It will be lit in green or red depending on the status
)
Green color indicates that the camera is in normal operation mode. Continuous green
indicates that data transmission is possible. Blinking green means that someone is connected to
Continuous or blinking red indicates that hardware is in abnormal condition.
Please insert SD memory card when you want
to use SD memory card. In case of pulling out SD memory
Connect external audio source or microphone.
Connect speakers with built in amplifier. Audio from remote site is output through Line out
LED will be lit with red momentarily and it will be lit with green after a while when power is
is powered by PoE, do not plug in DC Jack with active DC power
45) with PoE standard (802.3af). LED on the Ethernet connector shows
Green color indicates that the camera is in normal operation mode. Continuous green
indicates that data transmission is possible. Blinking green means that someone is connected to
Continuous or blinking red indicates that hardware is in abnormal condition.
to use SD memory card. In case of pulling out SD memory
Connect speakers with built in amplifier. Audio from remote site is output through Line out
in bi-directional
LED will be lit with red momentarily and it will be lit with green after a while when power is

O
Oi iD D4 4 U Us se er r’ ’s s G Gu ui id de e
Rev.1.0.2 (Jul. 2014) 13
 Sensor Input
Connect external alarm sensor. Examples of sensing devices are infrared sensor, motion sensor,
heat/smoke sensor, magnetic sensor, etc. Connect the two wires of the sensors to “Sensor Input”.
The sensor type (NC/NO) can be set in admin page. Multiple sensor devices can be connected in parallel.
Figure 2-6. SENSOR input and connection of the sensor
 Relay Output
Relay output is provided for connecting alarm devices or for remote on/off control of devices such as light.
Relay is normal open and it will be closed upon alarm annunciation or remote on. The relay is capable
of switching 30V AC/DC, 2A. For the application which needs power switching beyond this limit, use
additional relay switch as shown in the right of Figure 2-7.
* Left : switching requirement below 30V, 2A
* Right : switching requirement higher than 30V, 2A. Apply this connection when either voltage or
current exceed the limit.
Figure 2-7. RELAY Output connection
Alarm
Out
Device
Power
Supply
( ~30V)
( ~ 2A)
(DC/AC)
Alarm
Out
Device
Power
Supply
(30V~ )
( 2A~ )
(DC/AC)
Optional
Relay
Switch
Power
Supply
( ~30V)
( ~ 2A)
(DC/AC)
Relay Relay
Photo Coupler NO/NC Type Open Collector Type
Sensor1+
Sensor
Device
Sensor1-
Sensor
Device
Sensor
Power
Supply
Sensor
Power
Supply
GND
+12V

O
Oi iD D4 4 U Us se er r’ ’s s G Gu ui id de e
Rev.1.0.2 (Jul. 2014) 14
3. On Site Installation
Use cables and conduits that are suitable for the installation. Particular attention should be paid in the
installation so that no moisture is allowed to penetrate into the unit through the cables or conduits during the life
time of the product. Products of which the internal parts are exposed to moisture because of improper
installation are not covered by warranty
1. Open the dome cover
2. Make a hole for cables.
3. Connect cables
* After supplying power (DC or PoE), check the LED indicator
4. Fix the camera on wall or ceiling using screw provided.
5. Adjust direction and focus using two levers. First time levers are fastened. Unfasten the levers and then
adjust. After finishing focus control, fasten the lever to keep focus.
6. Assemble dome cover.
TILT : 90˚
Horizontal
Rotation :
360˚
PAN : 360˚
ZOOM
FOCUS

O
Oi iD D4 4 U Us se er r’ ’s s G Gu ui id de e
Rev.1.0.2 (Jul. 2014) 15
4. Getting Started
Brief information for first time operation of OiD4 is provided in this chapter.
4.1. PC Requirement
Audio/Video streaming data received from OiD4 can be displayed or stored in a PC running client programs.
Minimum requirement of the PC is described below:
ITEM Minimum Requirement Recommended Specification
CPU Intel Core i3 3Ghz Intel Core i7
Main Memory 2GB 4GB
Operating System
*
Windows XP Windows 7 (64bit)
Web Browser Internet Explorer 8, 9 Internet Explorer 8, 9
Graphic Card Video RAM 256MB
Resolution 1920x1080
Video RAM 1GB
Higher than 1920x1080
Network 10 Base-T Ethernet 100 Base-T Ethernet
* Operating Systems supported: Windows 2000 Professional, Windows XP / Vista / 7

O
Oi iD D4 4 U Us se er r’ ’s s G Gu ui id de e
4.2. Quick Installation Guide
4.2.1. Connect PC and OiD4
to network.
1.
Prepare a PC to run programs for the installation and video connection
(PC is needed to assign IP address to
2. In the case of using PoE
, connect the PC and
your LAN Switch does not support standard PoE, connect
The DC power is applied through DC adapter.
Figure 4
4.2.2. Install Speco-NVR
and set IP parameters on
Speco-NVR is a multi-
channel VMS program for the IP camera. Install Speco
connect to these
products. It is needed to assign connection information to Speco
connection. Insert the CD provided with product into the PC and install Speco
to network.
Prepare a PC to run programs for the installation and video connection
(PC is needed to assign IP address to
OiD4)
, connect the PC and
OiD4
to the network using one of the following ways. If
your LAN Switch does not support standard PoE, connect
OiD4
as shown in dotted line in Figure 4
The DC power is applied through DC adapter.
Figure 4
-1. Power and network connection
and set IP parameters on
OiD4
channel VMS program for the IP camera. Install Speco
-
NVR on remote PC to
products. It is needed to assign connection information to Speco
-
NVR program before
connection. Insert the CD provided with product into the PC and install Speco
-NVR.
Figure 4-2. Speco-NVR
LAN switch with
standard POE
(802.3af)
LAN switch
DC adaptor
Admin Page Button
ONSIP Installer
to the network using one of the following ways. If
as shown in dotted line in Figure 4
-1.
NVR on remote PC to
NVR program before
Admin Page Button

O
Oi iD D4 4 U Us se er r’ ’s s G Gu ui id de e
Follow the sequence below for setting the IP parameter
i) Run ONSIP installer
ii) Click
(1) in ONSIP installer window.> Double click on (2) > Fill in (4) > make a selection in (5) > Fill
the parameters in (6)
iii) Click on
(9) to apply the settings.
iv) You can connect t
o admin page by clicking on (10).
Click on the field in (3)
for sorting and rearranging the list.
Select network mode that best suits from the drop down list in
ADSL and Auto (DHCP), respectively. If ADSL and Auto
deactivated.
In case of ADSL, fill the User Name and Password in (8) with the values provided by your ISP.
If DDNS service is needed, Check at the box and fill the empty field with hostname you want in
(7).
2
4
7
Follow the sequence below for setting the IP parameter
(1) in ONSIP installer window.> Double click on (2) > Fill in (4) > make a selection in (5) > Fill
(9) to apply the settings.
o admin page by clicking on (10).
for sorting and rearranging the list.
Select network mode that best suits from the drop down list in
(5)
. You can choose either Static or
ADSL and Auto (DHCP), respectively. If ADSL and Auto
are selected, the fields in (6)
In case of ADSL, fill the User Name and Password in (8) with the values provided by your ISP.
If DDNS service is needed, Check at the box and fill the empty field with hostname you want in
3
(1) in ONSIP installer window.> Double click on (2) > Fill in (4) > make a selection in (5) > Fill
. You can choose either Static or
are selected, the fields in (6)
are
In case of ADSL, fill the User Name and Password in (8) with the values provided by your ISP.
If DDNS service is needed, Check at the box and fill the empty field with hostname you want in
1
6
9
5
8
10

O
Oi iD D4 4 U Us se er r’ ’s s G Gu ui id de e
4.2.3. Remote video connection to
OiD4
1. Connection through Web Viewer
Web Viewer offers simplest way of video connection to
address of OiD4
in the URL window of Internet Explorer as:
Note : Active-
X module should be installed on your PC before actual connection. If your PC is
not connected to the internet, you cannot download Active
installing the Active-
X module is
web site.
Default ID and password of Admin Page are
For more detailed information, please refer to the
Connection to Admin Page
[e.g.] Port 80
[e.g.] Port 8080
OiD4
Web Viewer offers simplest way of video connection to
OiD4
. For video connection, enter the IP
in the URL window of Internet Explorer as:
X module should be installed on your PC before actual connection. If your PC is
not connected to the internet, you cannot download Active
-
X module. Most convenient way of
X module is
installing Speco-NVR
which is available from the CD or our
Figure 4-3. Web Viewer
Default ID and password of Admin Page are
“admin”, “1234”.
For more detailed information, please refer to the
“Setup Guide”.
Connection to Admin Page
Basic Control
Default port 80 can be omitted
. For video connection, enter the IP
X module should be installed on your PC before actual connection. If your PC is
X module. Most convenient way of
which is available from the CD or our
Default port 80 can be omitted

O
Oi iD D4 4 U Us se er r’ ’s s G Gu ui id de e
2. Connection through Speco-NVR
Click the camera assignment button for setting the camera address. Input the description, address,
Ch#, User ID, Password and port and then click the save button. After assignment procedure, you must
click the SAVE button. You can see the live video when y
you exit Speco-
NVR, you have to input the ID/PW, admin/1234. Details for Speco
[Speco-NVR User’s Guide].
Example
Click the camera assignment button for setting the camera address. Input the description, address,
Ch#, User ID, Password and port and then click the save button. After assignment procedure, you must
click the SAVE button. You can see the live video when y
ou click the live view button as below. When
NVR, you have to input the ID/PW, admin/1234. Details for Speco
-
NVR can be found in
Figure 4-4. Speco-NVR
Camera Assignment
Live view
Exit Program
Default ID/PW: admin/1234
Camera Assignment
Example
Save
Click the camera assignment button for setting the camera address. Input the description, address,
Ch#, User ID, Password and port and then click the save button. After assignment procedure, you must
ou click the live view button as below. When
NVR can be found in
Camera Assignment

O
Oi iD D4 4 U Us se er r’ ’s s G Gu ui id de e
Rev.1.0.2 (Jul. 2014) 20
4.2.4. Additional settings through connection to the Admin Page
All parameters of the camera are factory default out of the box. For a more sophisticated target application,
parameters need to be changed through the admin page. The admin page can be connected through
“http://IP_Address:Port_Number/admin.htm”
ID and password of the administrator are required. Default ID and password are “admin”, “1234”.
It is highly recommended to change the ID and password to prevent illegal access to the IP camera.
For more detailed information, Please refer to the “Setup Guide”.