Spraying Systems TeeJet Aeros 9040 User manual

USER GUIDE
AEROS9040
Software version 4.21

Table of contents
START SIMPLE GUIDANCE 1
NO.1 POWER ON 1
NO.2 HOME SCREEN 1
System Setup .................................................................................................................................................................1
Simple or Advanced Mode.........................................................................................................................................1
NO.3 GO TO CONFIGURATION 2
1) Set Up the Local Cultural Settings.......................................................................................................................................................2
3) Set Up the Implement..............................................................................................................................................................................3
Implement Settings per Equipment Present...............................................................................................................3
Single Section Setup ......................................................................................................................................................3
Section(s) with ISOBUS Sprayer/Spreader Setup...........................................................................................................4
Multiple Sections with SDM/SFM and DCM with ISM/ASB Setup...................................................................................5
Additional Settings per Implement Type ....................................................................................................................5
Section Numbers .............................................................................................................................................................6
Straight ............................................................................................................................................................................6
Spreader – TeeJet............................................................................................................................................................7
Lateral Implement Offset Distance Adjustment ..........................................................................................................8
GNSS Offset Adjustment Calculation...............................................................................................................................8
Lateral Implement Offset Adjustment...............................................................................................................................9
NO.4 START NEW JOB OR CONTINUE JOB 10
Simple Mode ................................................................................................................................................................................................. 10
New Job..................................................................................................................................................................10
Continue Job...........................................................................................................................................................10
Close Job................................................................................................................................................................10
Advanced Mode........................................................................................................................................................................................... 10
New Job..................................................................................................................................................................10
Start Job .................................................................................................................................................................10
Close Job................................................................................................................................................................10
NO.5 SET UP GUIDANCE 11
1) Choose a Guidance Mode.................................................................................................................................................................... 11
2) Establish an AB guideline .................................................................................................................................................................... 12
3) Create an Application Boundary....................................................................................................................................................... 12
ADD RATE CONTROL 14
ISOBUS UNIVERSAL TERMINAL 14
Overview......................................................................................................................................................................................................... 14
Guidance Screen Options......................................................................................................................................................................... 14
Congure Product....................................................................................................................................................................................... 15
TEEJET DUAL CONTROL MODULE 16
Rate Control Screen Overview................................................................................................................................................................ 16
Congure Control Channels .................................................................................................................................................................... 17
Device Setup...........................................................................................................................................................17
Product Control Channels .......................................................................................................................................18
TankMatic ...............................................................................................................................................................18

iii
98-01504-EN R1
Aeros 9040 Field Computer
Congure Product....................................................................................................................................................................................... 19
APPLICATION MAPPING 20
Duplicating and Transferring Maps ..........................................................................................................................20
Coverage Map............................................................................................................................................................................................... 20
Prescription Map.......................................................................................................................................................................................... 20
Application Map........................................................................................................................................................................................... 21
Target Rate Map ........................................................................................................................................................................................... 21
Target Rates ...........................................................................................................................................................21
INFORMATION ON GUIDANCE MODES 22
Vehicle View................................................................................................................................................................................................... 22
Field View........................................................................................................................................................................................................ 23
RealView Guidance ..................................................................................................................................................................................... 24
GUIDANCE MODES 25
GUIDANCE SCREEN ICONS 26
GUIDANCE BAR 28
STATUS BAR 29
GUIDANCE FEATURES DETAILS 30
A+ Nudge Feature....................................................................................................................................................................................... 30
Azimuth Degree........................................................................................................................................................................................... 30
Return to Point.............................................................................................................................................................................................. 31
Marking a Return Point............................................................................................................................................31
Delete the Return Point...........................................................................................................................................31
Guidance to a Return Point .....................................................................................................................................31
Next Guideline Feature.............................................................................................................................................................................. 32
BOOMPILOT 32
No Section Control Module ..................................................................................................................................................................... 33
Console Only ..........................................................................................................................................................33
With Optional Work On/Off Switch...........................................................................................................................33
Using the Console..........................................................................................................................................................33
ISOBUS Sprayer............................................................................................................................................................................................. 33
Console and ECU Only ...........................................................................................................................................33
With Switchbox .......................................................................................................................................................34
With an ISOBUS Implement Status Module (ISO ISM).............................................................................................34
ISOBUS Spreader.......................................................................................................................................................................................... 34
Console Only ..........................................................................................................................................................34
With Optional Spreader On/Off Switch.....................................................................................................................35
With TeeJet Section Control Module and Switchbox or ISM........................................................................................................ 35
With TeeJet Section Control Module .................................................................................................................................................... 35
ADDITIONAL IMPLEMENT OPTIONS 36
NOZZLE SELECTION 36
Preset .....................................................................................................................................................................36
Current Nozzle ........................................................................................................................................................37
DROPLET SIZE MONITOR 37

iv www.teejet.com
Aeros 9040 Field Computer
Setup................................................................................................................................................................................................................ 37
Enable/Disable DSM ...............................................................................................................................................37
Nozzle Selection / Current Nozzle ...........................................................................................................................37
Input/Output Module Pressure Sensor.....................................................................................................................37
Operation ....................................................................................................................................................................................................... 38
Status Bar...............................................................................................................................................................38
Droplet Size Chart..........................................................................................................................................................38
Guidance Bar ..........................................................................................................................................................38
REVERSE SENSE MODULE 38
Reverse on Guidance Screens................................................................................................................................39
GROUND SPEED OVERRIDE 39
BOOMPILOT 40
BoomPilot Start Mode .............................................................................................................................................40
BoomPilot Icon........................................................................................................................................................40
NOZZLE FLOW MONITOR 41
DATA MANAGEMENT 41
Job Data .......................................................................................................................................................................................................... 42
Machine Settings......................................................................................................................................................................................... 42
SYSTEM CONFIGURATIONS 43
Safety information
TeeJet Technologies is not responsible for damage or physical harm caused by failure to adhere to the following safety
requirements.
As the operator of the vehicle, you are responsible for its safe operation.
The Aeros 9040 in combination with any assisted/auto steering device is not designed to replace the vehicle’s operator.
Do not leave a vehicle while the Aeros 9040 is engaged.
Be sure that the area around the vehicle is clear of people and obstacles before and during engagement.
The Aeros 9040 is designed to support and improve efciency while working in the eld. The driver has full responsibility for the quality and
work related results.
Disengage or remove any assisted/auto steering device before operating on public roads.

1
98-01504-EN R1
Aeros 9040 Field Computer
START SIMPLE GUIDANCE
NO.1 POWER ON
Integrated RAM Mount
(assembly required)
Speed Digital (LAN)
Connection
with Rubber Cover
Camera Connection
with Rubber Cover
Power Connection
Speakers
GNSS Antenna Connection
WiFi Antenna Connection
USB Ports with Rubber
Covers
USB Ports with Rubber Covers
Bright Touch Screen
Power Button
Favorites Button
Home Button
Recommended Antenna Installation
The GNSS antenna should be mounted as far forward as possible on
top of the cab on a metal surface of at least 4 in / 10 cm square.
Home Button
The Home button provides a shortcut to the Home screen.
Power On/Off Button
On – Press the POWER button to power on the console. Upon
power up, the Aeros will begin its start up sequence.
Off – Press and briey hold the POWER button until a
conrmation screen acknowledges shut down mode.
WARNING! Wait 10 seconds before restarting the console.
NO.2 HOME SCREEN
Once the power up sequence has completed, the Home screen will
appear with the options to start a new job or continue an existing job.
Home/Job Screen (or press Home Button)
Unit Setup
RealView Camera Full Screen Video View
ISOBUS Universal Terminal
System Setup
System Setup is used to congure the console, the machine and its
implements. Four side tabs access options for Machine/Implement
Conguration, Data Management, Console Settings, and Tools.
RealView Camera Full Screen Video View
View video feed(s) and setup cameras without GNSS available.
Options for RealView Guidance are not available on this screen.
ISOBUS Universal Terminal View
Access to an ISOBUS Electronic Control Unit (ECU) options and
operation. This provides crop sprayer or spreader control when
integrated into the implement of either capability.
Simple or Advanced Mode
To change between simple mode and advanced mode, see the
conguration chapter under Data –> Options.
►Simple Mode – only one job will be available at a time. Only
bounded area and coverage areas are displayed on the home
screen. Only the current job is available for saving in Reports.
Use with Fieldware Link is not available.
►Advanced Mode – more than one job will be available at any
time. Client, farm, eld and job names; bounded and coverage
areas; application time; and distance from selected job are
displayed on the home screen. All saved job proles can be
exported as a PDF, SHP or KML le to a USB drive using
Data -> Reports.