SSV Works RG4-5K User manual

•
SSVWORKS ,201 N. Rice Ave Unit A, Oxnard , CA 93030
www . SSVWorks.com I Phone :[phone] I Fax :[phone]
WARRANTY I NF O RMATION:
All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or workmanship .
All SSV Works Electronics are covered by a limited 1 year warranty against defects in material or workmanship .
All Kicker Speakers are covered by a limited 1 year warranty against defects in material or workmanship. All
Ki c ker Amplifiers are covered by a limited 2 year warranty against defects in material or workmanship. Labor for
replacement of defective components is not covered. Contact SSV Works for further warranty information.
RG4-5K
Polaris Range r
Kicke r5-Sp eake r Au dio Kit
A
Please read and understand these
instructions completely before
installation to avoid possible Injury , or
damage to the accessory or vehicle .
TOOLS NEEDED FOR INSTALLATION
PARTS LIST IMAGES
-T-40/30/25 Torx Driver - Phillips Screwdriver - Drill - 3/32" Bit -9/16" Bit - Uni-Bit
1. MRB3 Dash Kit
6. Rear B-H 1151 Speaker
ExAansion
11. USB/ AUX Input Port
- ..
♦ - <>
e .. •• •
- .. - ~
2. MRB3 Controller
7. Amp Power Wire x2
12 . B-H1221 MRB3 Power
& Ground Connector
3. Mounting Plate with
MRB3 Brain and Amps
~
~
-~ -. "4
, ,,
.. ..
8. Fuse Holderwith 40A
Fusex2
I
13. 3-Pin T-harness
B0-SS- H PGAT
4. MRB3 Controller/Dash 5. Front B-H 1149 Speaker
Screws x6 Harness
9. BatteryTerminal
Cablex2
14. Antenna
.?
10. ZipTies
II
A. Remove hood by turning locking pins and lifting up. B. Use a panel t ool toextract push pins circled in pink.

C. With push pins extracted ,lift to remove the cup holder.
E. Unscrew (4) tone screws located in upper glove box and
remove box.
G. Extract push pins exposed from cup holder removal.
I. Extract push pins located above driver and passenger side cup
holders .
D.Lift and disconnect gauge cluster for removal.
F. Extract push pins that are now exposed from removing the
upper glove box.
H. Extract push pins exposed from gauge cluster removal .
J. Lift to remove the dash .

K. Extract push pins located beneath 12v sockets.
M. Unscrew (2) tone screws that were behind the front dash panel.
----
L. Remove front dash panel and disconnect the 12v socket ha mess .
N. Unscrew the two (2) tone screws connecting the dash bracket at the rear of
the dash cavity . Remove the under dash bracket.
NOTE: ITWILL NOT BE RE - INSTALLED .
MRB3 / AMP MOUNTING PLATE AND DASH CONTROLLER INSTALLATION
- - - -
0. Move the factory wiring to the rear of the dash cavity. Place the
mounting plate in the former location of the factory bracket
Q. Fasten down the plate with the factory hardware .
P. With the mounting plate set in place, check for any pinched
wiring.
R. Run amp power, and speaker extension cables out through the
grommet that is fixed into the firewall (circled in pink). Be sure
to run the correct end of the cable out through the firewall to
avoid the inability to connect to the speakers. ,

S. With the cables now through the firewall , route them down the front of the machine to be full through the into the cabin of the
machine . NOTE: A1" hole may need to be drilled to run the cables down the front of the chassis .
T. Follow the air ducts and factory wiring and feed cables
towards the battery compartment. (use provided zip ties to
secure cables to factory wiring , away from the drive shaft) .
U. Feed power/ground and (2) H1151 harness down towards
the center console until you get the wires to the inside of the
vehicle.
'\ \- --- . ,~_ . tt . ..
.r\ '- - ._ \f ·
,~ , ·., .. \
' .
.. >.;
"1 \ V
V. Route the H 1149 harness towards the driver and passenger
side of the dash. Secure the harness with zip ties away from
any moving parts and any sharp metal .

W. Place MRB3 dash mount onto the center cup holder panel , and scribe the 4
comer mounting points . Make pilot holes using a3/32" drill bit.
Y. Place MRB3 controller in controller mount and fasten down
with provided screws .
X. Drill out the center of the cup holder for the controller cable
to be routed through with a9/16" drill bit.
NOTE : Control drill bit depth to avo id puncturing through
other side of cup holder .
II
Z. Route MRB3 controller cable through cup holder
Al. Fasten the dash mountto cup holder with provided screws .
• I
B2. Connect the antenna.
B2. Connect the MRB3 controller to the brain .
B3 . Connect the power/ground wire .

SSV WORKS , 201 N. Ri ce Ave Unit A, Oxnard , CA 93 030
www . SSVworks .c om I Phone : 818 - 991 - 1778 I Fa x: 86 6- 29 3- 6751
RG4-US10K
Polaris Ranger
Underseat 10" Subwoofer Enclosure
TOOLS NEEDED FOR INSTALLATION
PARTS LIST IMAGES
- T-30 & T-40 Torx Driver - 4mm Allen Key - Panel Removal Tool - Drill -13/64" Drill Bit
•
•
•
•
1. RG4-US10 Enc l osures 2. Enclosure Bracket A
2. Enclosure Bracket B 4. M6 Flathead 4mm 5. M6 Allen Torx 5. Foam Circles
Hex Screws x4 Screws x2 x4
NOTE: To avoid subwoo_fer damage, do not face the subwoofer down or rest the ~nclosure on the subwoofer when
installing bracket to the bottom of the enclosure.
A. Align bracket A's holes wi th the dimples/recess' circled in pink on the
bottom of the enclosure . Using four (4) flathead 4mm screws, mount
the A bracket to the bottom of the enclosure. After the bracket is secure ,
cover the screw heads with the (4) foam circles .
C. Using a panel removal tool , extract the (8) push pins to
remove the center drive line center column cover .
B. Flip up passenge r seat and remove center tray to access
battery. Disconnect the negat i ve battery cable from the battery .
D. Located on the floorboard to the right of the battery
compartment , remove the (3) T40 torx screws circled in pi nk .

E. Place SSV bracket B over the factory screw holes and refasten
down with the (3) factoryT40 torx screws removed in the
previous step.
F. With the bracket secured to the floorboard , place the enclosure in front of
the floorboard bracket. To allow proper engagement ,tilt the enclosure back
slightly and slide its bottom bracket into the floorboard bracket catch.
G. With the brackets seated into one another ,
use the front mounting tabs as a template
to mark with a scribe or punch the needed
placement to drill pilot holes.
H. Once marked , remove the enclosure. Using a
13/64" drill bit,drill pilot holes at your marked
points . Be sure to penetrate through the
chassis lying beneath the floorboard.
I.. Re-install the sub-enclosure . Secure the front
mounting tabs with . the kit provide T30 torx
self-tapping screws .
J. Connect sub to harness B-H1151 from the battery compartment.
K. Connect the dash end of the B-H 1151 harness to the amp .

SSVWORKS , 201 N. Rice Ave Unit A, Oxnard , CA 93030
www . SSVworks .c om I Phone : 818 - 991-1778 I Fax :[phone]
RG4-F65K
Po la r is Ranger
6.5" Speaker Front Ki ck Panels
TOOLS NEEDED FOR INSTALLATION
PARTS LIST IMAGES
- T-30 Torx Driver - Panel Removal Tool - Phillips Screwdriver
-
' ~
l- I
" ,,
. -
-
1. RG4-F65 Enclosures
(1 pair)
,,
,,
2. Enclosure Brackets x4 3. M6 x 16mm Screws
X 10
0
4. M6 Washers x8 (small) 4. M6 Washers x2 (large)
II
A. Using the supplied M6 screws and small washers, install the
brackets to kick pods.
II
C. Remove factoryT25 torx screws located underneath the dash.
B. Remove factory T40 torx screws located from the front of the
dash next to the cup holders.
II
D. Located on the inside top of the pocket you will have two
holes, route speaker wire though the larger hole. The smaller
hole will be used to mount the pod in Step P.

II
E. Place the speaker pod in location and resecure the factory screws through the pod brackets on the front and underneath the dash .
P. From the inside - top of the dash , secure the top mounting M6 screw and large washer to the pod through the smaller hole next to the routed speaker
wire (figure Fl). Then connect the B-H 1149 harness to the speaker cable coming out of the speaker pods (figure P2) .
G. Connect the dash end of the B-H 1151 harness to the amp .

SSVWORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030
www.SSVworks.com I Phone: [phone] I Fax: [phone]
- 5mm Allen Key
PARTS LIST I MAGES
1. US2-C65 Enclosures (1 pai~
0
5. M6 Allen Socket Head Bolts
&Washersx4
- 3mm Allen Key
2. Ranger C_ la mp x4
6. M6 Set Screws x8
A. Find the best orientation for the speaker on your bar and
screw in the Set Screws in the OPPOSITE holes of where the
clamp will install Into.
- 8mm Open End Wrench
RG -C 65K
Polaris Ranger
6.5" Speaker Cage Mount Pods
- #2 Phillips Screwdriver
0
3. Aftennarket Speaker Adapter
(comes with unloaded pods only)
4. M6 Hex Head Bolts &
Washers"x4
B. Loosely install the clamp base to the cage mount pod with the
two (2) M6 Hex head bolts and washers, place the cage mount
pod in the desired mounting location and tighten the hex head
bolts using a 8mm wrench.

II
C. Position the clamp underneath the rear crossbar
E. Place screws in the clamp and use a 5mm hex driver to tighten
the bracket
AUX/USB PORT INSTALLATION
A. Using a Uni-bit, drill a1• hole through the blank circular panel
between the 12v ports.
II
C. Feed the plastic nut back through the wires and cables and
screw back on to the port Hand tighten only. Re-insert the fuse
and close the fuse holder.
D. Slide the top mount for the clamp into the top crossbar notch
and line up screw holes.
F. Route the speaker wire away from any moving parts and any
sharp metal, then connect to the amplifier.
B. Unscrew and remove the plastic nut from the port Make sure
to open the fuse holder and remove the fuse so the nut will fit
through it Feed in the wires through the hole. Keep the fuse
holder open and empty until it has passed through the hole.
D. Connect the Aux-in plug to the MRB3 brain.

CONNECTING POWER
H. Feed the power and ground wires from the B-H 1221 (MRB3
brain power) and the USB/AUX port through the grommet
that passes through the firewall from under the dash to
under the hood.
B. From the B-HPGAT Harness: use accessory red wire for power to USB/ Aux adapter, use yellow wire for power to B-H 1221 from the MRB3 brain, both
grounds from USB/ Aux adapter and B-H 1221 crimp to black wire.
C. Connect the HPGAT harness to an empty port on the factory
buss bar located under the hood.

CONNECTING POWER & GROUND CABLE TO BATTERY
Break
off tab
-+
Power
Wire
Battery
Tenninal
Cable
AL Remove the bottom cover of the fuse holder A2 . Extract both fuse holder screws . A3 . Attach both the Power Wire and Battery
Terminal Cable to the fuse holder. Reattach
the bottom cover .
by extracting the 2 screws. Break off the right
and left side tabs on the bottom cover .
II
B. Unscrew . the factory nut on the negative battery terminal. Install
the 2 ground cables to the screw on the ground battery tenninal.
Re-install the factory nut
D. Remove the top of the fuse holder and extract the 2 screws . Insert the
40A fuse, screw the 2 screws back in and reattach the fuse holder top.
■
C. Unscrew the factory nut on the positive battery terminal. Install the 2
power cables to the screw on the postive battery terminal. Re - install
the factory nut.
E. Zip tie all of the electrical cabling (factory and audio) along the cente r
column away from the drive shaft
, THIS CONCLUDES THE INSTALLATION PROCESS. REPLACE Tl-IE FACTORY PANELS AND SEATS.
QUESTIONS? PLEASE CONTACT SSV WORKS AT 818-991-1778 OR EMAIL [email protected]
© 2018 SSVWorks , Oxnard , CA 93030 RG4 - 5K Rev .A 12 -21-18