SSV Works RZR XP1000 User manual

RZ3-BSSB10
RZR XP1000
Behind Seat 10” Subwoofer Enclosure
SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030
www.SSVworks.com | Phone: [phone] | Fax: [phone]
!
Please read and understand these
instructions completely before
installation to avoid possible injury, or
damage to the accessory or vehicle.
WARRANTY INFORMATION:
All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or
workmanship. All SSV Works Electronics are covered by a limited 1 year warranty against defects in
material or workmanship. All SSV Works Speakers are covered by a limited 1 year warranty against
defects in material or workmanship. Labor for replacement of defective components is not covered.
Contact SSV Works for further warranty information.
1. RZ3-BSSB10 Enclosure x 1
2. M6 x 1.0 Screws x 10
3. M6 Washers x 10
4. 1/4”x 20 Screws x 4
5. 1/4” Washers x 4
TOOLS NEEDED FOR INSTALLATION PARTS LIST
PARTS LIST IMAGES
6. 7/16” Nuts x 4
7. Top Mounting Bracket x 1
8. Bottom Mounting Bracket x 1
9. Subwoofer Grill x 1
2. M6 x 1.0 Screws x 10
6. 7/16” Nuts x 4
1. RZ3-BSSB10 Enclosure x 1
5. 1/4” Washers x 4
9. Subwoofer Grill x 1
3. M6 Washers x 10
7. Top Mounting Bracket x 1
4. 1/4 x 20 Screws x 4
8. Bottom Mounting
Bracket x 1
- Wire Crimpers
- Wire Strippers
- T-30 Torx Wrench
- 5/32” Allen Wrench
- 7/16” Socket or Wrench
- Panel Removal Tool
- Drill with 1/8” and ¼” Drill bit
- Wrench for Battery Terminal
- #3 Phillips Screwdriver

C. The 2 holes in the top bracket will line up with the 2 holes in
the vehicle crossbar behind the plastic panel, the enclosure
can shift left or right to align these holes
D. Once the enclosure is in position, loosely install the lower
bracket
B. Place the enclosure in the vehicle bottom rst and rotate
the top into place. The top bracket is in the proper location
when it is behind the plastic top panel (NOTE: For proper t on
2016+ models you may need to reverse the nut/bolt on the
rear crossbar, the bolt head should face downward and the
nut should be on the top of the bar)
RZ3-BSSB10
C D
B
A. Loosely install the top mounting bracket onto the enclosure
A
INSTALLATION NOTES
The use of a thread locker is recommended on all screws to prevent loosening due to vibration. This enclosure will not work with some
aftermarket headers, conrm t before beginning installation. Begin by unlatching the seats from the vehicle; remove the center hump using
the panel removal tool on the 5 plastic panel clips and the T-30 Torx for the top 2 bolts. Remove the rear panel that sits behind the seats
using a T-30 to remove the 7 Torx bolts, and a panel removal tool to remove the 4 plastic panel clips. Once the panel is loosened, unplug the
computer harness then “push” the panel down behind the seat belt retractors, after it is free from behind the top panel; pull up and away from
the vehicle. Once the panel is out, remove the 2 seat belt bolts that hold the center seat belt receivers.

E. After the enclosure is properly aligned, tighten the 2 seat belt
receiver bolts and the screws on the face of the enclosure
G. On the rear panel that was removed for installation of the
subwoofer enclosure, remove the access door. Align the SSV
Works grill over the door opening and mark the 4 mounting
locations, drill the holes using the ¼” drill bit. Mount the grill
to the panel using the 5/32” Allen and the 7/16” wrench.
F. Drill a ¼” hole for the speaker wire to exit the enclosure, seal
this hole using silicone sealer. Drill the 8 mounting locations for
the subwoofer using the 1/8” drill bit, then connect the speaker
wires to the subwoofer, be sure to connect the “+” speaker wire
to the “+” subwoofer terminal and the “-“ speaker wire to the “-“
subwoofer terminal. Mount the subwoofer in the enclosure.
H. Route the speaker wire away from any moving parts and any
sharp metal, then connect to the amplier, after the system has
been tested, re assemble any vehicle parts that were removed.
RZ3-BSSB10
E
G
F
H
WIRING INSTRUCTIONS
For proper sound, ensure the speaker polarity is correct connect the “+” to the “+” and the “-“to the “-“from the speaker wire to the amplier. If using with
an SSV Works complete system refer to the amplier wiring instructions for more detailed wiring information.
“+”
“+”
“ - ”
“ - ”
Amplier
© 2017 SSV Works, Oxnard, CA 93030 RZ3-BSSB10 Rev. C 5-3-17