SSV Works SS-FKP652 User manual

SS-FKP652
Polaris Slingshot
Front Kick Panels
SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030
www.SSVworks.com | Phone: [phone] | Fax: [phone]
!
Please read and understand these
instructions completely before
installation to avoid possible injury, or
damage to the accessory or vehicle.
WARRANTY INFORMATION:
All SSV Works enclosures are covered by a limited lifetime warranty against defects in
material or workmanship. All SSV Works Electronics are covered by a limited 1 year
warranty against defects in material or workmanship. Labor for replacement of defective
components is not covered. All SSV Works Speakers are covered by a limited 1 year
warranty against defects in material or workmanship. Contact SSV Works for further
warranty information.
1. SS-FKP652-U Enclosures
(1 pair)
2. Triangle Block off Plates x 2
3. Tweeter Mounting Plates x 2
TOOLS NEEDED FOR INSTALLATION PARTS LIST
PARTS LIST IMAGES
4. “J” Bracket x 2
5. M6 x 1 x 20mm Screws x 6
6. M6 Washers x 12
7. M6 x 1 x 16mm Screws x 6
2. Triangle Block Off Plates x 2
1. SS-FKP652-U Enclosures (1 pair)
4. “J” Bracket x 2 5. M6 x 1 x 20mm Screws x 6 6. M6 Washers x 12 6. M6 x 1 x 16mm Screws x 6
3. Tweeter Mounting Plates x 2
- Wire Crimpers
- Wire Strippers
- Drill with 1/8” and 1/4” Drill bit
- #2 Phillips Screwdriver
- #3 Phillips Screwdriver
- Scribe or Marker
INSTALLATION NOTES
The use of a thread locker is recommended on all screws to prevent loosening due to vibration. If the vehicle is equipped with factory speaker
enclosures, remove those prior to beginning the installation.

B. Place the speaker into the enclosure and mark the 4 mounting
holes with a scribe or marker, Pre-drill the marked mounting
locations using a 1/8” drill.
B. If using a coaxial speaker, connect and install the speaker into the enclosure using the #2
Phillips screwdriver (be sure to connect the “+” speaker wire to the “+” terminal on the speaker
and the “-“ speaker wire to the “-“ terminal on the speaker), then install the triangle block off
plate using the 16mm (smaller) screws, repeat for other side.
SS-FKP652
B
C C
A. Drill a 1/4” hole in the enclosure for the speaker wire to run
out of, we recommend the at side under the logo, toward the
top of the enclosure.
A
D. If mounting a component tweeter, mount the tweeter into the tweeter mounting plate using the
16mm (smaller) screws, install into the enclosure, then connect and install the speaker into the
enclosure using the #2 Phillips screwdriver (be sure to connect the “+” speaker wire to the “+” terminal
on the speaker and the “-“ speaker wire to the “-“ terminal on the speaker), repeat for other side.
D D

SS-FKP652
For proper sound, ensure the speaker polarity is correct connect the “+” to the “+” and the “-“to the “-“from the speaker wire to the amplier. If using
with an SSV Works complete system refer to the amplier wiring instructions for more detailed wiring information.
© 2017 SSV Works, Oxnard, CA 93030 SS-FKP652 Rev. C 4-11-17
E. Loosen the screws for the 2 mounting brackets on the
enclosure and place into the cage.
G. Attach the “J” bracket to the underside of the enclosure, be
sure the bracket hooks tight around the cage bar, then tighten.
H. Route the speaker wire away from any moving parts and any
sharp metal, then connect to the amplier.
E
G H
B. Mount the enclosure brackets into the vehicle using the M6 screws provided,
once the brackets are tight to the cage, re-tighten the brackets to the enclosure.
F F
WIRING INSTRUCTIONS
“+”
“+”
“ - ”
“ - ”
Amplier