SSV Works RZ3-FKP65 User manual

RZ3-FKP65
RZR XP1000 & 2015+ RZR900
6.5” Speaker Front Kick Panels
SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030
www.SSVworks.com | Phone: [phone] | Fax: [phone]
!
Please read and understand these
instructions completely before
installation to avoid possible injury, or
damage to the accessory or vehicle.
WARRANTY INFORMATION:
All SSV Works enclosures are covered by a limited lifetime warranty against defects
in material or workmanship. All SSV Works Electronics are covered by a limited 1 year
warranty against defects in material or workmanship. All SSV Works Speakers are
covered by a limited 1 year warranty against defects in material or workmanship. Labor
for replacement of defective components is not covered. Contact SSV Works for further
warranty information.
1. RZ3-FKP65-U Enclosures (1 pair)
2. 1/4” x 20 Allen Bolt x 6
TOOLS NEEDED FOR INSTALLATION
INSTALLATION NOTES
PARTS LIST
PARTS LIST IMAGES
3. 1/4” Washers x 6
4. 7/16” Nut x 6
The use of a thread locker is recommended on all screws to prevent loosening due to vibration. If installing an SSV Works RZ3-GBSB10 Glove
Box subwoofer enclosure, install the subwoofer enclosure rst, then complete the passenger side kick panel installation. The removal of the
fender are is not required; however it will make the installation easier.
2. 1/4 x 20 Allen Bolt x 6
1. RZ3-FKP65 Enclosures
(1 pair)
3. 1/4” Washers x 6 4. 7/16” Nut x 6
- Wire Crimpers
- Wire Strippers
- T-40 Torx Driver
- 7/16” Open End or Socket
- 5/32 Allen Wrench
- Drill with 1/4” and 1/8”
Drill bit
- #2 Phillips Screwdriver
- Utility Knife
- Scribe or Marker

C. Align the kick panel against the rewall and side of the vehicle
(under the glove box on the passenger side & mid way up the
rewall on the driver side), the pod is in the correct location
when it sits ush against the re wall and side walls. Using the
scribe, mark the 3 mounting holes
D. After marking the holes, drill the 3 mounting locations on
each side using the ¼” drill bit
F. Once the mounting holes and the speaker wire hole have
been drilled mount the kick panel in the vehicle, installing
the Allen bolt with the the nut on the inside of the enclosure is
recommended
E. Drill a hole in each kick panel for the speaker wire to exit
(seal this hole with silicone sealer for increased sound and
weatherproong). The hole can be on the top, or the side of the
enclosure, if the side is chosen, the side wall of the vehicle will
need to be drilled for the speaker wire to exit the interior
B. Using the utility knife or another cutting tool cut off the two
plastic factory nubs in the foot well, cut these as smooth as
you can to the panel
RZ3-FKP65
C D
FE
B
A. Remove the ten T40 Torx bolts that secure the 2 piece fender.
Note: there is one screw inside the fender well. Remove the
two additional screws from the striker plate, slide fender up
the cage rail and secure
A

H. Connect and install the speaker into the enclosure (be sure to connect the “+”
speaker wire to the “+” terminal on the speaker and the “-“ speaker wire to the “-“
terminal on the speaker) using the #2 Phillips screwdriver, repeat for other side
H. Route the speaker wire away from any moving parts and any
sharp metal, then connect to the amplier
RZ3-FKP65
HI H
WIRING INSTRUCTIONS
For proper sound, ensure the speaker polarity is correct connect the “+” to the “+” and the “-“to the “-“from the speaker wire to the amplier. If using with
an SSV Works complete system refer to the amplier wiring instructions for more detailed wiring information.
“+”
“+”
“+”
“+”
“ - ”
“ - ”
“ - ”
“ - ”
Amplier
© Copyright 2016 SSV Works, Oxnard, CA 93030 RZ3-FKP65 Rev. B 4-10-17
G. Place the speaker into the enclosure and mark the 4 mounting holes with a
scribe or marker, pre-drill these locations with the 1/8” drill bit
G G