stellar labs Slider34 User manual

Slider34 Hooklift
Owner’s Manual
Stellar Industries, Inc.
190 State Street
PO Box 169
Garner, IA 50438
800-321-3741
Fax: [phone]
www.stellarindustries.com
Subject to Change without Notification.
© 2021 Stellar Industries, Inc.
Rev 1
PN 41994
Installation • Assembly Drawings • Parts

Page ii | Stellar®Slider34 Owner’s Manual
Slider Hooklift Manual Revisions
Date of Revision Section Revised Description of Revision

Stellar®Slider34 Owner’s Manual | Page iii
Table of Contents
Introduction iv
Serial Tag Location...................................................................................................................................................................... v
Chapter 1 - Specifications...............................................................................................................................................................1
Slider34 Specifications................................................................................................................................................................ 1
Slider34 Latch Locations for Skid Compatibility....................................................................................................................... 2
Slider34 Grease Zerk Locations.................................................................................................................................................. 3
Chapter 2 - Installation ....................................................................................................................................................................5
General Installation .................................................................................................................................................................... 5
Installer Notice ......................................................................................................................................................................... 5
Torque Data Chart .................................................................................................................................................................. 6
Installation Note....................................................................................................................................................................... 7
Step 1: Set the hooklift onto the truck frame........................................................................................................................... 7
Step 2: Drill mounting holes........................................................................................................................................................ 7
Step 3: Install bumper. ................................................................................................................................................................ 8
Step 4: Install tie-downs. ............................................................................................................................................................. 8
Step 5: Install tarper tower (If applicable). .............................................................................................................................. 8
Step 6: Install hydraulic reservoir and valve bank................................................................................................................... 8
Reservoir Assembly (2 Section Cable Controls) - PN 86463................................................................................................ 9
Reservoir Assembly (3 Section Cable Controls) - PN 86473.............................................................................................. 10
Reservoir Assembly (2 Section Air Controls) - PN 86466 .................................................................................................... 11
Reservoir Assembly (3 Section Air Controls) - PN 86477 .................................................................................................... 12
Reservoir Subassembly - PN 86006....................................................................................................................................... 13
Step 7: Install PTO and pump. ................................................................................................................................................. 16
Step 8: Route hydraulic hoses. ................................................................................................................................................ 17
Hose Kit - PN 58089 (Fixed Hook Height Models) ............................................................................................................... 17
Hose Kit - PN 84955 (Adjustable Hook Height Models)...................................................................................................... 18
Power Beyond VDM8 Valve ................................................................................................................................................. 19
Step 9: Route Electrical Components .................................................................................................................................... 20
Step 10: Install cab and PTO controls. .................................................................................................................................... 21
Cable Controls ...................................................................................................................................................................... 21
Air Controls............................................................................................................................................................................. 22
Step 11: Install Hoist Up Light Sensor - PN 83115 .................................................................................................................... 23
Step 12: Install mud flaps and fenders.................................................................................................................................... 24
Poly Tandem Fender Assembly - PN 58217......................................................................................................................... 24
Steel Tandem Fender Assembly - PN 100617 ..................................................................................................................... 25
Step 13A: Apply Hooklift Assembly Decals ............................................................................................................................ 26
Step 13B: Apply Chassis Decals............................................................................................................................................... 27
Step 14: Fill reservoir and activate hydraulic flow................................................................................................................. 28
Step 15: Operate hooklift......................................................................................................................................................... 28
Set System Relief Pressure..................................................................................................................................................... 29
Chapter 3 - Assembly Drawings ................................................................................................................................................... 31
Base Assembly - PN 59206........................................................................................................................................................ 31
Dump Assembly - PN 59208 ..................................................................................................................................................... 33
Secondary Assembly - PN 57788............................................................................................................................................. 34
Main Cylinder Assembly - PN 58053........................................................................................................................................ 35
Jib Assembly (54” Hook Height) - PN 47054 ........................................................................................................................... 36
Jib Assembly (54” Hook Height) w/Dock Latches- PN 55321............................................................................................... 37
Jib Assembly (61.75” Hook Height) - PN 46704 ...................................................................................................................... 38
Jib Assembly (61.75” Hook Height) w/Dock Latches - PN 57484......................................................................................... 39
Jib Assembly (61.75” Hook Height) - PN 56864 ...................................................................................................................... 40
Jib Assembly (54/61.75” Hook Height) - PN 43504 ................................................................................................................ 41
Hose Track - PN 59128............................................................................................................................................................... 43
Slider34 Cylinder Assemblies.................................................................................................................................................... 44
Valve Bank Parts Drawing ........................................................................................................................................................ 45
Toolbox Assembly - PN 8480..................................................................................................................................................... 46
Toolbox Assembly - PN 10401................................................................................................................................................... 46
Toolbox Assembly - PN 10402................................................................................................................................................... 46

Page iv | Stellar®Slider34 Owner’s Manual
Introduction
A copy of this manual is provided with every hooklift and can be found in the hard plastic
manual case that is installed on the chassis. A copy of this manual shall remain with the
hooklift at all times.
Throughout the manual, three signal words will be used to bring attention to important
items:
A NOTICE signal word indicates a practice not related to physical injury.
A WARNING signal word indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
A DANGER signal word indicates a hazardous situation which, if not
avoided, will result in death or serious injury.
Information contained within this manual does not cover operation, maintenance, or trou-
bleshooting. Please refer to the General Slider Hooklift Manual for details on these items.
This manual is not binding. Stellar Industries, Inc. reserves the right to change, at any time,
any or all of the items, components, and parts deemed necessary for product improve-
ment or commercial/production purposes. This right is kept with no requirement or obliga-
tion for immediate mandatory updating of this manual.
In closing:
If more information is required or technical assistance is needed, or if you feel that any part
of this manual is unclear or incorrect, please contact the Stellar Customer Service Depart-
ment by phone at 800-321-3741 or email at [email protected].
WARNING
NOTICE
DANGER
For Technical Questions, Information, Parts, or Warranty, Call Toll-Free at
800-321-3741
Hours: Monday - Friday, 8:00 a.m. - 5:00 p.m. CST
Or email at the following addresses:
Technical Questions, and Information [email protected]
Order Parts [email protected]
Warranty Information [email protected]

Stellar®Slider34 Owner’s Manual | Page v
The serial tag should be located on the right side (passenger side) of the base assembly:
FOR SERVICE ON THIS EQUIPMENT
CONTACT:
STELLAR INDUSTRIES, INC.
190 STATESTREET, GARNER, IA 50438
641-923-3741
800-321-3741
4214
®
35234
ProudlyDesigned
andManufactured
inthe USA by
MODELNO. SERIALNO.
DATE
MADEIN THE U.S.A. BY STELLAR INDUSTRIES, INC. PN C5942
THEFOLLOWING U.S. OR FOREIGN PATENTSMAY APPLY:
U.S.PATENTS
6,749,389 6,558,104 5,427,495
5,108,247 6,065,942 5,082,417
CANADIANPATENTS
6,749,389
5,108,247
WARNING
25627 - Rev B
Moving parts can crush
and cut.
Keep hands and arms
clear when operating
equipment.
Crush Hazard
DANGER
Electrocution Hazard
Death or serious injury will result from
inadequate clearance if hooklift, load,
or vehicle becomes electrically
charged.
• Maintain safe clearance from high
voltage power sources.
• Never approach vehicle or load if
equipment is near a high voltage
power source.
55832 - RevA
Serial Tag Location
MODEL NO. SERIAL NO.
DATE
MADE IN THE U.S.A. BY STELLAR INDUSTRIES, INC.
PN C5942
®
PATENT INFORMATION
http://www.stellarindustries.com/ip

Page vi | Stellar®Slider34 Owner’s Manual
This page intentionally left blank.

Stellar®Slider34 Owner’s Manual | Page 1
L
K
A
G
J
EB
C
C
D
H
I
Chapter 1 - Specifications
54” (1,372mm) Fixed Hook Height 61.75” (1,569mm) Fixed Hook
Height
54” (1,372mm) to 61.75” (1,569mm)
Adjustable Hook Height
Lifting Capacity 28,800 lbs (13,063 kg) 34,000 lbs (15,422 kg) 28,800 lbs - 34,000 lbs (13,063 kg - 15,422
kg)
Dumping Capacity 34,000 lbs (15,422 kg) 34,000 lbs (15,422 kg) 34,000 lbs (15,422 Kg)
A Dump Angle 50° 50° 50°
B Lowest Hook Height 48” (1,219 mm) 42” (1,067 mm) 48” or 42” (1,219 mm or 1,067 mm)
C Effective Length 168” to 208” (4,267 mm to 5,283
mm)
168” to 208” (4,267 mm to 5,283
mm) 168” to 208” (4,267 mm to 5,283 mm)
D Truck Frame Height 41” (1,041 mm) 41” (1,041 mm) 41” (1,041 mm)
E Hooklift Height 52.63” (1,337 mm) 52.63” (1,337 mm) 52.63” (1,337 mm)
F Hooklift Length 216” (5,486 mm) 216” (5,486 mm) 216” (5,486 mm)
G Hooklift Center of Gravity 101” (2,565 mm) 101.45” (2,577 mm) 97” (2,464 mm)
H Chassis Cab to Axle 180” to 188” (4,572 mm to 4,775
mm))***
180” to 188” (4,572 mm to 4,775
mm))*** 180” to 188” (4,572 mm to 4,775 mm)***
I Chassis Cab to Trunion 160” to 174” (4,064 mm to 4,420
mm))***
160” to 174” (4,064 mm to 4,420
mm))*** 160” to 174” (4,064 mm to 4,420 mm)***
J Max. Height When Loading 164” (4,166 mm) 164” (4,166 mm) 164” (4,166 mm)
K Longest Body When Dumping 252” (6,401 mm) 252” (6,401 mm) 252” (6,401 mm)
L Max. Height When Dumping 252” (6,041 mm) 252” (6,041 mm) 252” (6,041 mm)
Maximum Operating Pressure 4,265 psi (29.4 MPa) 4,265 psi (29.4 MPa) 4,265 psi (29.4 MPa)
Hydraulic Flow 24 gpm (91 lpm) 24 gpm (91 lpm) 24 gpm (91 lpm)
Shipping Weight 4,300 lbs (1,950 kg) 4,300 lbs (1,950 kg) 4,475 lbs (2,030 kg)
Shipping Dimensions (LxWxH) 211” x 78” x 53” 211” x 78” x 53” 211” x 78” x 53”
Minimum Truck GVWR 32,000 lbs (14,515 kg) 32,000 lbs (14,515 kg) 32,000 lbs (14,515 kg)
Load Angle w/Shortest Body
Length 38° 36° 38° or 36°
Recommended Container
Lengths* 14’ to 20’ (4.9 to 6.7 m) 14’ to 20’ (4.9 to 6.7 m) 14’ to 20’ (4.9 to 6.7 m)
Recommended Flatbed
Lengths** 14’ to 21’ (4.9 to 7.3 m) 14’ to 21’ (4.9 to 7.3 m) 14’ to 21’ (4.9 to 7.3 m)
*Assumes 3 ft. overhang from
center of rear roller pin (Bumper
typically 12” from center of
roller pin)
**Assumes 5 ft. overhang from
center of rear roller pin (May re-
quire bumper and latch options)
***Weight Distribution Required
Slider34 Specifications

Page 2 | Stellar®Slider34 Owner’s Manual
Slider34 Latch Locations for Skid Compatibility

Stellar®Slider34 Owner’s Manual | Page 3
Slider34
QTY. (2) QTY. (2)
QTY. (2)
QTY. (2)
QTY. (2)
QTY. (2)
QTY. (2)
QTY. (2)
QTY. (2)
Note: Grease After Every 100 Cycles.
Slider34 Grease Zerk Locations

Page 4 | Stellar®Slider34 Owner’s Manual
This page intentionally left blank.

Stellar®Slider34 Owner’s Manual | Page 5
Chapter 2 - Installation
Installer Notice
According to Federal Law (49 cfr part 571), each final-stage manufacturer shall complete the vehi-
cle in such a manner that it conforms to the standards in effect on the date of manufacture of the
incomplete vehicle, the date of final completion, or a date between those two dates. This require-
ment shall, however, be superseded by any conflicting provisions of a standard that applies by its
terms to vehicles manufactured in two or more stages.
Therefore, the installer of Stellar®Hooklifts is considered one of the manufacturers of the vehicle.
As such a manufacturer, the installer is responsible for compliance with all applicable federal and
state regulations. They are required to certify that the vehicle is in compliance with the Federal
Motor Vehicle Safety Standards and other regulations issued under the National Traffic and Motor
Vehicle Safety Act.
Please reference the Code of Federal Regulations, title 49 - Transportation, Volume 5 (400-999), for
further information, or visit http://www.gpoaccess.gov/nara/index.html for the full text of Code of
Federal Regulations.
General Installation
This chapter is designed to serve as a general guide for the installation of a Stellar®Slider34
Hooklift. Each installation is considered unique so certain portions of this chapter may or
may not apply to your direct application. If a question should arise during the installation
process, please contact Stellar Customer Service at [phone].
PTO and Pump installation instructions are provided by the corresponding manufacturers.
For more information on which PTO and Pump fit your application, please contact your
local Stellar Distributor or Stellar Customer Service.
Do not install this hooklift on a chassis not capable of handling the loads
imposed on it. Failure to do so may result in serious injury or death.
Do not weld or drill holes into the side wall of the base tubes.
Hooklift Mounting and Assembly
Study names and locations of the parts and familiarize yourself with the hooklift before
starting the assembly . Reading the step-by-step instructions that follow will be helpful.
Assembly
Select an area for assembly that will be large enough to accommodate the completed
unit. The surface of the work area should be as level as possible. Use the proper hand
tools to ensure proper bolt tightness. Refer to the torque data chart in this chapter for the
recommended torque values for different sizes of bolts.
Model Number
Know the model number of the Stellar®Hooklift being mounted. Use this model number
whenever referring to the assembly or parts listing pages. The number is stamped on the
name plate which is located on the front frame member.
WARNING
NOTICE

Page 6 | Stellar®Slider34 Owner’s Manual
When using the torque data in the
chart, the following rules should be
observed:
• Bolt manufacturer’s particular
specifications should be consulted
when provided.
• Flat washers of equal strength
must be used.
• All torque measurements are giv-
en in foot-pounds. To convert to
inch-pounds, multiply by 12.
• Torque values specified are for
bolts with residual oils or no special
lubricants applied. If special lubri-
cants of high stress ability, such as
Never-Seez compound graphite
and oil, molybdenum disulphite,
colloidal copper or white lead are applied, multiply the torque values in the charts by the
factor .90. The use of Loctite does not affect the torque values listed above.
• Torque values for socket-head capscrews are the same as for Grade 8 capscrews.
• Do not use these values if a different torque value or tightening procedure is given for
a specific application. Torque values listed are for general use only. Check tightness of
fasteners periodically.
• Sheer bolts are designed to fail under predetermined loads. Always replace shear bolts
with identical grade.
• Fasteners should be replaced with the same or higher grade. If higher grade fasteners
are used, these should only be tightened to the strength of the original.
• Tighten plastic insert or crimped steel-type lock nuts to approximately 110 percent of the
dry torque values shown in the chart below, applied to the nut, not to the bolt head.
Tighten toothed or serrated-type lock nuts to the full torque value. Note: “Lubricated”
means coated with a lubricant such as engine oil, or fasteners with phosphate and oil
coatings. “Dry” means plain or zinc plated without lubrication. Tighten lubricated bolts
to approximately 80% of dry bolts.
Size Bolt DIA Plain Plated Plain Plated Plated
(DIA-TPI) (Inches) (Ft-Lb) (Ft-Lb) (Ft-Lb) (Ft-Lb) (Ft-Lb)
5/16-18 0.3125 17 13 25 18 22
3/8-16 0.3750 31 23 44 33 39
7/16-14 0.4375 49 37 70 52 63
1/2-13 0.5000 75 57 105 80 96
9/16-12 0.5625 110 82 155 115 139
5/8-11 0.6250 150 115 220 160 192
3/4-10 0.7500 265 200 375 280 340
7/8-9 0.8750 395 295 605 455 549
1-8 1.000 590 445 910 680 823
1 1/8-7 1.1250 795 595 1290 965 1167
1 1/4-7 1.2500 1120 840 1815 1360 1646
1 3/8-6 1.3750 1470 1100 2380 1780 2158
1 1/2-6 1.500 1950 1460 3160 2370 2865
GRADE 5 GRADE 8 GRADE 9
Torque Data Chart

Stellar®Slider34 Owner’s Manual | Page 7
• When positioning mounts to frame, tie-down castings are bolted to the underside of
each tie down plate located on the outside of the main rails of the base. The tie-down
plate closest to the front of the base requires one mount on each side of the pin. This
is the only time two tie down castings are required per a single tie-down plate. The tie-
down plates are designed with multiple slots to offer more flexibility in mounting locations.
Additional holes may not be added to the tie-down plates.
• Using the tie-down castings as a guide, drill 11/16” holes through the truck frame as
shown.
Step 2: Drill mounting holes.
• Visually inspect the truck and look for any potential issues. For example: Clearance
problems, cross members extending too high, insufficient room in front of the Slider for
tarpers, exhaust manifolds, etc., or insufficient room in the rear to allow for bumper se-
lection. Note: Stellar Industries recommends allowing 12” behind the start of clear truck
frame for installation of a tarping system.
• Be sure to square the Slider on the truck frame to allow for proper measurement. The
front of the hooklift needs to be at least 2.50” behind the cab or any equipment mount-
ed behind the cab. Note: On some Slider models, the jib may extend beyond the front
of the base.
Step 1: Set the hooklift onto the truck frame.
Every hooklift installation is unique. However, certain guidelines exist that apply to every
model. Listed below is a general set of chronological steps that may be followed when
installing a Stellar Hooklift. If any questions arise during the installation process, feel free to
contact your local dealer or Stellar Customer Service at 800-321-3741.
Installation Note
Note: Only the front angle mount requires four (4) bolts to install the angle mount to the truck frame
and four (4) bolts to install the hooklift to the angle mount.
The rear three (3) angle mounts require two (2) bolts each to install the angle mount to the truck frame
and two (2) bolts to install the hooklift to the angle mount.

Page 8 | Stellar®Slider34 Owner’s Manual
Note: See torque chart at beginning of chapter:
Step 4: Install tie-downs.
NOTE: MULTIPLE HOLES ARE PREDRILLED ON THE BASE MOUNTING FLATS. ADDITIONAL HOLES MAY NOT BE ADDED.
PN 58058
ITEM PART DESCRIPTION QTY.
1 57081PC ANGLE 4.00X6.00X.50WX22.00 SLOTS 2
2
57079PC
ANGLE FORMED 4.00X4.00X0.50X12.88
SLOTS
2
35199
CAP SCR 1.00X8X3.00 HHGR8 ZY 40
46538
WASHER 1.00 SAE FLAT YELLOW GR8 80
56294
NUT 1.00 HHGR8 NYLOC 40
6
57733PC ANGLE 4.00X6.00X.50WX11.00 SLOTS 4
758060 LOADER SLIDER34 TACOM 1
3
3
4
4
2
6
4
4
3
3
4
4
5
5
4
5
5
4
1
• See NHTSA (National Highway Truck Safety Administration) Regula-
tions for acceptable placement.
• Modify the truck frame as necessary so that it ends 2” from the
rear of the hooklift.
Step 3: Install bumper.
2.00
• Before drilling and bolting to the frame, confirm adequate room for cable routing be-
tween in-cab controls and the valve bank. Note: The top of the reservoir should not be
above the truck frame.
See brand specific installation instructions.
Step 5: Install tarper tower (If applicable).
Step 6: Install hydraulic reservoir and valve bank.

Stellar®Slider34 Owner’s Manual | Page 9
Reservoir Assembly (2 Section Cable Controls) - PN 86463
11
1
18
3
2
4
14
17
13
13
8
19
21
NOTE: ITEMS NOT SHOWN
25941 - DECAL LOADER VB VDM8 HOSE LOCATION X 1
42971 - DECAL OIL FILTER CHANGE X 1
ITEM PART DESCRIPTION QTY.
186006
RSRVR ASM 25GAL K MODEL W/ TANK
TOP FILTER
1
27353
FTG 32-32 MP-MP HEX NIPPLE STRAIGHT
1
3 C4750 VALVE BALL 2.00
1
4 C4730 FTG 32-32 MP-HB STRAIGHT
1
524611 VB 2-SECTION VDM8
1
60521 WASHER 0.25 LOCK
3
70339 CAP SCR 0.25-20X2.50 HHGR5
3
860395 FTG 16-20 MFS-MAORB 90 1
9
C2252 FTG 8-10 MFS-MORB STRAIGHT
2
10 16152 FTG 10-10 MFS-MORB STRAIGHT
2
11 27119 HOSE 0.75(78C-12-JC-JC-12-12-12-120)
1
12 10094 GAUGE OIL LF 2.5" 0-5000 BM
1
13 c4819 HOSE CLAMP 2.00
2
14 17766 HOSE SUCT 2.00 10FT
1
15 25630 FTG 10-4 MORB-FP STRAIGHT
1
16 d1435 FTG 12-10 MFS-MORB STRAIGHT
1
17 c4903 FTG 12-12 MFS-FFSS 90
1
18 83959 MNT KIT RSRVR 25G
1
19 86168
HOSE 0.75(300PSI)-16FFSS SHORT-12FFSS
90 SHORT-7.75CL
1
20
C2142 FTG 12-12 MFS-MORB STRAIGHT 1
21
C6327 FILTER STRAINER 35GAL TF-2030 1
PN 86463

Page 10 | Stellar®Slider34 Owner’s Manual
Reservoir Assembly (3 Section Cable Controls) - PN 86473
NOTE: ITEMS NOT SHOWN
25941 - DECAL LOADER VB VDM8 HOSE LOCATION X 1
42971 - DECAL OIL FILTER CHANGE X 1
26182 - PORT RELIEF VDM8 2500 PSI X 2
ITEM PART DESCRIPTION QTY.
186006
RSRVR ASM 25GAL K MODEL W/ TANK
TOP FILTER
1
27353
FTG 32-32 MP-MP HEX NIPPLE STRAIGHT 1
3
C4750 VALVE BALL 2.00 1
4
C4730 FTG 32-32 MP-HB STRAIGHT 1
538230
VB 3-SECT VDM8 1
60521
WASHER 0.25 LOCK 3
760395
FTG 16-20 MFS-MAORB 90 1
8
C1855 FTG 6-10 MFS-MORB STRAIGHT 4
916152
FTG 10-10 MFS-MORB STRAIGHT 2
10 27119
HOSE 0.75(78C-12-JC-JC-12-12-12-120) 1
11 10094
GAUGE OIL LF 2.5" 0-5000 BM 1
12
C4819 HOSE CLAMP 2.00 2
13 17766
HOSE SUCT 2.00 10FT 1
14 25630
FTG 10-4 MORB-FP STRAIGHT 1
15
d1435 FTG 12-10 MFS-MORB STRAIGHT 1
16 c4903
FTG 12-12 MFS-FFSS 90 1
17 0339
CAP SCR 0.25-20X2.50 HHGR5 3
18 83959
MNT KIT RSRVR 25G 1
19 86168
HOSE 0.75(300PSI)-16FFSS SHORT-12FFSS
90 SHORT-7.75CL
1
20
C2142 FTG 12-12 MFS-MORB STRAIGHT 1
21
C6327 FILTER STRAINER 35GAL TF-2030 1
PN 86473
10
18
3
2
4
13
16
12
12
19
7
1
21

Stellar®Slider34 Owner’s Manual | Page 11
Reservoir Assembly (2 Section Air Controls) - PN 86466
NOTE: ITEMS NOT SHOWN
25941 - DECAL LOADER VB VDM8 HOSE LOCATION X 1
42971 - DECAL OIL FILTER CHANGE X 1
ITEM PART DESCRIPTION QTY.
186006
RSRVR ASM 25GAL K MODEL W/ TANK
TOP FILTER
1
27353
FTG 32-32 MP-MP HEX NIPPLE STRAIGHT 1
3
C4750 VALVE BALL 2.00 1
4
C4730 FTG 32-32 MP-HB STRAIGHT 1
525940
VB 2-SECTION VDM8 W/AIR ACTUATORS 1
60521
WASHER 0.25 LOCK 3
70339
CAP SCR 0.25-20X2.50 HHGR5 3
860395
FTG 16-20 MFS-MAORB 90 1
9
C1855 FTG 6-10 MFS-MORB STRAIGHT 2
10 16152
FTG 10-10 MFS-MORB STRAIGHT 2
11 27119
HOSE 0.75(78C-12-JC-JC-12-12-12-120) 1
12 10094
GAUGE OIL LF 2.5" 0-5000 BM 1
13
C4819 HOSE CLAMP 2.00 2
14 17766
HOSE SUCT 2.00 10FT 1
15 25630
FTG 10-4 MORB-FP STRAIGHT 1
16
d1435 FTG 12-10 MFS-MORB STRAIGHT 1
17 c4903
FTG 12-12 MFS-FFSS 90 1
18 83959
MNT KIT RSRVR 25G 1
19 86168
HOSE 0.75(300PSI)-16FFSS SHORT-12FFSS
90 SHORT-7.75CL
1
20
C2142 FTG 12-12 MFS-MORB STRAIGHT 1
21
C6327 FILTER STRAINER 35GAL TF-2030 1
PN 86466
11
1
18
3
2
4
14
17
13
13
19
8
21

Page 12 | Stellar®Slider34 Owner’s Manual
Reservoir Assembly (3 Section Air Controls) - PN 86477
NOTE: ITEMS NOT SHOWN
25941 - DECAL LOADER VB VDM8 HOSE LOCATION X 1
42971 - DECAL OIL FILTER CHANGE X 1
26182 - PORT RELIEF VDM8 2500 PSI X 2
ITEM PART DESCRIPTION QTY.
186006
RSRVR ASM 25GAL K MODEL W/ TANK
TOP FILTER
1
27353 FTG 32-32 MP-MP HEX NIPPLE STRAIGHT
1
3 C4750 VALVE BALL 2.00
1
4 C4730 FTG 32-32 MP-HB STRAIGHT
1
547562 VB 3-SECTION VDM8 W/AIR ACTUATORS
1
60521 WASHER 0.25 LOCK
3
7 C1855 FTG 6-10 MFS-MORB STRAIGHT
4
816152 FTG 10-10 MFS-MORB STRAIGHT
2
927119 HOSE 0.75(78C-12-JC-JC-12-12-12-120)
1
10 10094 GAUGE OIL LF 2.5" 0-5000 BM
1
11 c4819 HOSE CLAMP 2.00
2
12 17766 HOSE SUCT 2.00 10FT
1
13 25630 FTG 10-4 MORB-FP STRAIGHT
1
14 d1435 FTG 12-10 MFS-MORB STRAIGHT
1
15 c4903 FTG 12-12 MFS-FFSS 90
1
16 0339 CAP SCR 0.25-20X2.50 HHGR5
3
17 83959 MNT KIT RSRVR 25G
1
18 60395 FTG 16-20 MFS-MAORB 90
1
19 86168
HOSE 0.75(300PSI)-16FFSS SHORT-12FFSS
90 SHORT-7.75CL
1
20 C2142 FTG 12-12 MFS-MORB STRAIGHT
1
21 C6327 FILTER STRAINER 35GAL TF-2030 1
PN 86477
9
3
2
4
12
15
11
11
1
19
18
21

Stellar®Slider34 Owner’s Manual | Page 13
Reservoir Subassembly - PN 86006
9
10
7
8
6
3
2
5
1
4
11
NOTE: REPLACEMENT OIL FILTER - PN 86010
ITEM PART DESCRIPTION QTY
1 C2126 MAGNETIC PLUG DRAIN 3/4" 1
2 15463
THERMO SIGHT GAUGE ZINGA SG-O5-A-T-N 1
3 73278
CAP FILL 1PSI ZINGA THREADED 1
4 13002
DECAL HYD OIL SPECIFICATION MOBIL 1
5 86007
RSRVR 25GAL K MODEL W/ TANK TOP FILTER 1
6 66656
FILTER PIPE TANK TOP 1
7 85928
FILTER TANK TOP 20 FORB 1
8 58396
GASKET RG-11 TANK TOP FILTER 1
9 0335
CAP SCR 0.38-16X1.25 HHGR5 4
10
C6353 WASHER 0.38 SAE FLAT YELLOW GR8 4
11
C4845 PLUG 0.75 NPT SQ HD BLK 1
PN 86006
NOTE: REPLACEMENT GASKET
UNDER FILTER CAP - PN 109546

Page 14 | Stellar®Slider34 Owner’s Manual
Step 6: Install hydraulic reservoir and valve bank continued...
ITEM PART DESCRIPTION QTY
19
26
27 13 12
11
10
29
9
NOTE:
PLUG TOP
#12 PORT
9 47562 VB 3-SECTION VDM8 W/AIR ACTUATORS
1
10 0521 WASHER 0.25 LOCK
3
11 C5968 FTG ADAPT 90 12-C5OLO-S
1
12
C1855
FTG ADAPT 6-10 F5OLO-S
4
13 16152 FTG ADAPT 10-F5OLO-S 2
19 10094
GAUGE OIL LF 2.5" 0-500 BM
1
26 25630 FTG ADAPT 10-1/4 F5OG
1
27 d1435 FTG ADAPT O'RING 12-10
1
29 0339 CAP SCR 0.25-20X2.50 HHGR5
3