stellar labs 120-16-20 User manual

120-16-20
Shuttle Hooklift
Owner’s Manual
Stellar Industries, Inc.
190 State Street
PO Box 169
Garner, IA 50438
800-321-3741
Fax: [phone]
www.stellarindustries.com
Subject to Change without Notification.
© 2021 Stellar Industries, Inc.
Rev 1
PN 24254
Installation • Assembly Drawings • Parts

Page ii | Stellar®120-16-20 Shuttle Owner’s Manual
Model 120-16-20 Manual Revisions
Date of Revision Section Revised Description of Revision

Stellar®120-16-20 Shuttle Owner’s Manual | Page iii
Table of Contents
Introduction.............................................................................................................................................................iv
Hooklift Nomenclature........................................................................................................................................... v
Serial Tag Location .................................................................................................................................................vi
Chapter 1 - Specifications.......................................................................................................................................... 1
Model 120-16-20 Shuttle Specifications ............................................................................................................... 1
Acceptable Subframe Dimensions - Model 120-16-20 ...................................................................................... 2
Chapter 2 - Installation ............................................................................................................................................... 3
General Installation ................................................................................................................................................ 3
Installer Notice ..................................................................................................................................................... 3
Torque Data Chart .............................................................................................................................................. 4
Installation Note................................................................................................................................................... 5
Step 1: Set the hooklift onto the truck frame. ..................................................................................................... 5
Step 2: Bolt tie-down castings to mounting plates. ............................................................................................ 6
Step 3: Drill mounting holes into frame rail........................................................................................................... 7
Step 4: Bolt tie-down castings to truck frame. .................................................................................................... 7
Step 5: Install bumper............................................................................................................................................. 8
Step 6: Install tarper tower (If applicable). .......................................................................................................... 8
Step 7: Install hydraulic reservoir and valve bank. ............................................................................................. 8
Reservoir Assembly (Cable Controls) - PN 87078............................................................................................. 9
Reservoir Assembly (Air Controls) - PN 87081 ................................................................................................. 10
Reservoir Subassembly - PN 86117................................................................................................................... 11
Valve Bank Parts Drawing.................................................................................................................................... 13
Step 8: Install PTO and pump. ............................................................................................................................. 14
Face Seal/O-Ring Size Chart ............................................................................................................................... 15
Step 9: Route hydraulic hoses. ............................................................................................................................ 15
Hose Kit - PN 81682 ............................................................................................................................................ 16
Power Beyond VDM8 Valve ............................................................................................................................. 17
Step 10: Route Electrical Components .............................................................................................................. 18
Step 11: Install cab and PTO controls................................................................................................................. 19
Cable Controls................................................................................................................................................... 19
Air Controls ......................................................................................................................................................... 20
Step 12: Install Hoist Up Alarm - PN 83115 .......................................................................................................... 21
Step 13: Install mud flaps and fenders. .............................................................................................................. 22
Poly Fender Assembly - PN 6170 ...................................................................................................................... 22
Step 14A: Apply Hooklift Assembly Decals ........................................................................................................ 23
Step 14B: Apply Chassis Decals .......................................................................................................................... 24
Step 15: Fill reservoir and activate hydraulic flow............................................................................................. 25
Step 16: Operate hooklift..................................................................................................................................... 25
Set System Relief Pressure................................................................................................................................. 26
Chapter 3 - Assembly Drawings .............................................................................................................................. 27
Base Assembly - PN 81684 ................................................................................................................................... 27
Dump Assembly - PN 81460................................................................................................................................. 28
Secondary Assembly - PN 81461......................................................................................................................... 29
Tilt Assembly 54” Hook Height - PN 79418 .......................................................................................................... 30
Tilt Assembly 61.75” Hook Height - PN 85778 ..................................................................................................... 31
Main Cylinder - PN 19026..................................................................................................................................... 32
Tilt Cylinder - PN 23159 ......................................................................................................................................... 33
Optional Tab Alarm Kit - PN 43120...................................................................................................................... 34
Optional Tab Alarm (cont.) - PN 43120 .............................................................................................................. 35
Optional Tab Alarm Wire Harness - PN 26291 .................................................................................................... 36
Optional Proximity Switch Wire Harness - PN 26416 .......................................................................................... 37

Page iv | Stellar®120-16-20 Shuttle Owner’s Manual
Introduction
A copy of this manual is provided with every hooklift and can be found in the hard plastic
manual case that is installed on the chassis. A copy of this manual shall remain with the
hooklift at all times.
Throughout the manual, three signal words will be used to bring attention to important
items:
A NOTICE signal word indicates a practice not related to physical injury.
A WARNING signal word indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
A DANGER signal word indicates a hazardous situation which, if not
avoided, will result in death or serious injury.
Information contained within this manual does not cover operation, maintenance, or trou-
bleshooting. Please refer to the General Shuttle Hooklift Manual for details on these items.
This manual is not binding. Stellar Industries, Inc. reserves the right to change, at any time,
any or all of the items, components, and parts deemed necessary for product improve-
ment or commercial/production purposes. This right is kept with no requirement or obliga-
tion for immediate mandatory updating of this manual.
In closing:
If more information is required or technical assistance is needed, or if you feel that any part
of this manual is unclear or incorrect, please contact the Stellar Customer Service Depart-
ment by phone at 800-321-3741 or email at [email protected].
WARNING
NOTICE
DANGER
For Technical Questions, Information, Parts, or Warranty, Call Toll-Free at
800-321-3741
Hours: Monday - Friday, 8:00 a.m. - 5:00 p.m. CST
Or email at the following addresses:
Technical Questions, and Information [email protected]
Order Parts [email protected]
Warranty Information [email protected]

Stellar®120-16-20 Shuttle Owner’s Manual | Page v
Hooklift Nomenclature
The Stellar®Shuttle is a hydraulic, body-loading device when mounted on a truck chassis. It
can handle a multitude of bodies ranging from flatbeds to recycling containers and dump
bodies.
The Shuttle consists of four basic parts: the base, dump, secondary, and tilt sections. Please
take the time to familiarize yourself with the various components. Knowing the proper ter-
minology is necessary to get the full benefit of this manual.
HOOKLIFT
BASE
DUMP
SECONDARY
TILT

Page vi | Stellar®120-16-20 Shuttle Owner’s Manual
The serial tag should be located on the right side (passenger side) of the base assembly:
FOR SERVICE ON THIS EQUIPMENT
CONTACT:
STELLAR INDUSTRIES, INC.
190 STATE STREET,GARNER, IA 50438
641-923-3741
800-321-3741
4214
35234
Proudly Designed
and Manufactured
in the USA by
DANGER
Electrocution Hazard
Death or serious injury will result from
inadequate clearance if hooklift, load,
or vehicle becomes electrically
charged.
• Maintain safe clearance from high
voltagepower sources.
• Never approach vehicle or load if
equipmentis near a high voltage
powersource.
55832 - RevA
MODELNO.SERIALNO.
DATE
MADE IN THE U.S.A. BY STELLAR INDUSTRIES, INC.
PN C5942
®
PATENTINFORMAT ION
http://www.stellarindustries.com/ip
WARNING
25627 - Rev B
Moving parts can crush
and cut.
Keep hands and arms
clear when operating
equipment.
Crush Hazard
Serial Tag Location
MODEL NO. SERIAL NO.
DATE
MADE IN THE U.S.A. BY STELLAR INDUSTRIES, INC.
PN C5942
®
PATENT INFORMATION
http://www.stellarindustries.com/ip

Stellar®120-16-20 Shuttle Owner’s Manual | Page 1
A
G
E
I
D
H
C
L
J
B
K
Chapter 1 - Specifications
Model 120-16-20 Shuttle Specifications
Model 120-16-20 Shuttle
Lifting/Dumping Capacity 20,000 lbs (9,072 kg)
ADump Angle 48°
BLowest hook Height 41" (104 cm)
CEffective Length 146" (371 cm)
DTruck Frame Height 41" (104 cm)
EHooklift Height 50.38" (127.97 cm)
GHooklift Length 159" (404 cm)
HHooklift Center of Gravity 61" (155 cm)
IChassis Cab to Axle 114" to 130" (290 to 330 cm)
JMax Height When Loading 143" (363 cm)
KLongest Body to Dump 204" (518 cm)
LMax Height when Dumping 204" (518 cm)
Operating Pressure 4200 psi
Hydraulic Flow Not to exceed 16 GPM
Shipping Weight 2,600 lbs (1,179 kg)
Hook Height 54" (137 cm)
Shipping Dimensions (LxHxW) 159" x 74" x 47"
Minimum Truck GVWR 20,000
RBM 900,000
Load Angle w/Shortest Body Length 35º
Recommended Body Lengths* 12.5' to 15' (3.81 to 4.57 m)
Recommended Flatbed Body Lengths**to 17' (5.18 m)
* Assumes 3ft. overhang from center of rear roller pin.
* Assumes 5ft. overhang from center of rear roller pin - May require bumper and latch options.

Page 2 | Stellar®120-16-20 Shuttle Owner’s Manual
Acceptable Subframe Dimensions - Model 120-16-20

Stellar®120-16-20 Shuttle Owner’s Manual | Page 3
Chapter 2 - Installation
Installer Notice
According to Federal Law (49 cfr part 571), each final-stage manufacturer shall complete the vehi-
cle in such a manner that it conforms to the standards in effect on the date of manufacture of the
incomplete vehicle, the date of final completion, or a date between those two dates. This require-
ment shall, however, be superseded by any conflicting provisions of a standard that applies by its
terms to vehicles manufactured in two or more stages.
Therefore, the installer of Stellar®Hooklifts is considered one of the manufacturers of the vehicle.
As such a manufacturer, the installer is responsible for compliance with all applicable federal and
state regulations. They are required to certify that the vehicle is in compliance with the Federal
Motor Vehicle Safety Standards and other regulations issued under the National Traffic and Motor
Vehicle Safety Act.
Please reference the Code of Federal Regulations, title 49 - Transportation, Volume 5 (400-999), for
further information, or visit http://www.gpoaccess.gov/nara/index.html for the full text of Code of
Federal Regulations.
General Installation
This chapter is designed to serve as a general guide for the installation of a Stellar®Shuttle
120-16-20 Hooklift. Each installation is considered unique so certain portions of this chap-
ter may or may not apply to your direct application. If a question should arise during the
installation process, please contact Stellar Customer Service at [phone].
PTO and Pump installation instructions are provided by the corresponding manufacturers.
For more information on which PTO and Pump fit your application, please contact your
local Stellar Distributor or Stellar Customer Service.
Do not install this hooklift on a chassis not capable of handling the loads
imposed on it. Failure to do so may result in serious injury or death.
Do not weld or drill holes into the side wall of the base tubes.
Hooklift Mounting and Assembly
Study names and locations of the parts and familiarize yourself with the hooklift before
starting the assembly . Reading the step-by-step instructions that follow will be helpful.
Assembly
Select an area for assembly that will be large enough to accommodate the completed
unit. The surface of the work area should be as level as possible. Use the proper hand
tools to ensure proper bolt tightness. Refer to the torque data chart in this chapter for the
recommended torque values for different sizes of bolts.
Model Number
Know the model number of the Stellar®Hooklift being mounted. Use this model number
whenever referring to the assembly or parts listing pages. The number is stamped on the
name plate which is located on the front frame member.
WARNING
NOTICE

Page 4 | Stellar®120-16-20 Shuttle Owner’s Manual
When using the torque data in the
chart, the following rules should be
observed:
• Bolt manufacturer’s particular
specifications should be consulted
when provided.
• Flat washers of equal strength
must be used.
• All torque measurements are giv-
en in foot-pounds. To convert to
inch-pounds, multiply by 12.
• Torque values specified are for
bolts with residual oils or no special
lubricants applied. If special lubri-
cants of high stress ability, such as
Never-Seez compound graphite
and oil, molybdenum disulphite,
colloidal copper or white lead are applied, multiply the torque values in the charts by the
factor .90. The use of Loctite does not affect the torque values listed above.
• Torque values for socket-head capscrews are the same as for Grade 8 capscrews.
• Do not use these values if a different torque value or tightening procedure is given for
a specific application. Torque values listed are for general use only. Check tightness of
fasteners periodically.
• Sheer bolts are designed to fail under predetermined loads. Always replace shear bolts
with identical grade.
• Fasteners should be replaced with the same or higher grade. If higher grade fasteners
are used, these should only be tightened to the strength of the original.
• Tighten plastic insert or crimped steel-type lock nuts to approximately 110 percent of the
dry torque values shown in the chart below, applied to the nut, not to the bolt head.
Tighten toothed or serrated-type lock nuts to the full torque value. Note: “Lubricated”
means coated with a lubricant such as engine oil, or fasteners with phosphate and oil
coatings. “Dry” means plain or zinc plated without lubrication. Tighten lubricated bolts
to approximately 80% of dry bolts.
Size Bolt DIA Plain Plated Plain Plated Plated
(DIA-TPI) (Inches) (Ft-Lb) (Ft-Lb) (Ft-Lb) (Ft-Lb) (Ft-Lb)
5/16-18 0.3125 17 13 25 18 22
3/8-16 0.3750 31 23 44 33 39
7/16-14 0.4375 49 37 70 52 63
1/2-13 0.5000 75 57 105 80 96
9/16-12 0.5625 110 82 155 115 139
5/8-11 0.6250 150 115 220 160 192
3/4-10 0.7500 265 200 375 280 340
7/8-9 0.8750 395 295 605 455 549
1-8 1.000 590 445 910 680 823
1 1/8-7 1.1250 795 595 1290 965 1167
1 1/4-7 1.2500 1120 840 1815 1360 1646
1 3/8-6 1.3750 1470 1100 2380 1780 2158
1 1/2-6 1.500 1950 1460 3160 2370 2865
GRADE 5 GRADE 8 GRADE 9
Torque Data Chart

Stellar®120-16-20 Shuttle Owner’s Manual | Page 5
• Visually inspect the truck and look for any potential issues. For example: Clearance
problems, cross members extending too high, insufficient room in front of the hooklift for
tarpers, exhaust manifolds, etc., or insufficient room in the rear to allow for bumper se-
lection. Note: Stellar Industries recommends allowing 12” behind the start of clear truck
frame for installation of a tarping system.
• Be sure to square the hooklift on the truck frame to allow for proper measurement. The
front of the hooklift needs to be at least 2.50” behind the cab or any equipment mount-
ed behind the cab.
Step 1: Set the hooklift onto the truck frame.
Every hooklift installation is unique. However, certain guidelines exist that apply to every
model. Listed below is a general set of chronological steps that may be followed when
installing a Stellar Hooklift. If any questions arise during the installation process, feel free to
contact your local dealer or Stellar Customer Service at 800-321-3741.
Installation Note
10.13
.40
2.50
4.78

Page 6 | Stellar®120-16-20 Shuttle Owner’s Manual
Bolt each tie-down casting to the underside of each mounting plate located on the out-
side of the main rails of the base (both sides):
Note: The mounting plates are designed with multiple slots to offer more flexibility in mount-
ing locations. Additional holes may not be added.
Step 2: Bolt tie-down castings to mounting plates.
ITEM PART DESCRIPTION
QTY.
1 24868 NUT 0.63-11 HHGR8 NYLOCK ZY 8
2
C5902 WASHER 0.63 SAE FLAT YELLOW GR8 16
3
C1026 CAP SCR 0.63-11X2.50 HHGR8 ZY 8
4
D0143 TIE DOWN CHANNEL 4
22
1
2
3
2
4

Stellar®120-16-20 Shuttle Owner’s Manual | Page 7
Bolt each tie-down angle to the truck frame (both sides):
Step 4: Bolt tie-down castings to truck frame.
ITEM PART DESCRIPTION QTY.
124868 NUT 0.63-11 HHGR8 NYLOCK ZY 8
2
C5902 WASHER 0.63 SAE FLAT YELLOW GR8 16
3
C1026 CAP SCR 0.63-11X2.50 HHGR8 ZY 8
22
1
3
22
Using the holes in the tie-down castings as guides, drill 11/16” mounting holes
through the truck frame as shown (both sides):
Step 3: Drill mounting holes into frame rail.
11/16"

Page 8 | Stellar®120-16-20 Shuttle Owner’s Manual
Mounting Kit - PN 1022
22
1
1
3
2
3
2
4
ITEM PART DESCRIPTION QTY.
124868 NUT 0.63-11 HHGR8 NYLOCK ZY 16
2
C5902 WASHER 0.63 SAE FLAT YELLOW GR8 32
3
C1026 CAP SCR 0.63-11X2.50 HHGR8 ZY 16
4
D0143 TIE DOWN CHANNEL 8
PN 1022
•See NHTSA (National Highway Truck Safety Administration) Regulations for acceptable
placement.
• Modify the truck frame as necessary so that it ends 2” from the rear of the hooklift.
Step 5: Install bumper.
2.00
See brand specific installation instructions.
• Before drilling and bolting to the frame, confirm adequate room for cable routing be-
tween in-cab controls and the valve bank. Note: The top of the reservoir should not be
above the truck frame. Refer to the Reservoir Assembly Drawings for details.
Step 6: Install tarper tower (If applicable).
Step 7: Install hydraulic reservoir and valve bank.

Stellar®120-16-20 Shuttle Owner’s Manual | Page 9
11
10
9
10
3
2
1
16
15
8
14
18
22
21
19
23
NOTE: ITEMS NOT SHOWN 25941 - DECAL LOADER VB VDM8 HOSE LOCATION X 1 42971 - DECAL OIL FILTER CHANGE X 1
ITEM
PART
DESCRIPTION
QTY.
11115
FTG 20-20 MP-MP HEX NIPPLE STRAIGHT
1
2
C5511
VALVE BALL 1.25
1
3
C2282
FTG 1.25 NPT TO 1.25 BARB
1
424611 VB 2-SECTION VDM8
1
50521
WASHER 0.25 LOCK
3
60339
CAP SCR 0.25-20X2.50 HHGR5
3
7
C1855
FTG 6-10 MFS-MORB STRAIGHT
4
8
D0549
FTG 16-8 MORB-FORB STRAIGHT REDUCER 1
917767
HOSE SUCT 1.25 10FT
1
10
C0075
HOSE CLAMP HC125
2
11
C4747
FTG 20-16 HB-MAORB 45 1
12 10094
GAUGE OIL LF 2.5" 0-5000 BM
1
13 25630
FTG 10-4 MORB-FP STRAIGHT
1
14
C2376 FTG 8-8 MFS-FFSS 90
1
15 1554
FTG 8-8 MFS-MORB STRAIGHT
1
16 31676
HOSE 0.50(471TC-JC-JC-8-8-8-120)
1
17
C2252
FTG 8-10 MFS-MORB STRAIGHT
1
18 84341
MNT KIT RSRVR 10GAL
1
19 86117
RSRVR ASM 10GAL K MODEL W/ TANK TOP FILTER
1
20
C2142
FTG 12-12 MFS-MORB STRAIGHT
1
21
C5968
FTG 12-12 MFS-MAORB 90
1
22 87077
HOSE 0.75(300PSI)-12FFSS SHORT-12FFSS 90 SHORT-7.50CL
1
23
C5552
FILTER STRAINER TFS-1220-0
1
PN 87078
Reservoir Assembly (Cable Controls) - PN 87078

Page 10 | Stellar®120-16-20 Shuttle Owner’s Manual
11
10
9
10
3
2
1
16
15
8
14
18
22
21
19
23
NOTE: ITEMS NOT SHOWN 25941 - DECAL LOADER VB VDM8 HOSE LOCATION X 1 42971 - DECAL OIL FILTER CHANGE X 1
ITEM
PART
DESCRIPTION
QTY.
11115
FTG 20-20 MP-MP HEX NIPPLE STRAIGHT
1
2
C5511
VALVE BALL 1.25
1
3
C2282
FTG 1.25 NPT TO 1.25 BARB
1
425940
VB 2-SECTION VDM8 W/AIR ACTUATORS
1
50521
WASHER 0.25 LOCK
3
60339
CAP SCR 0.25-20X2.50 HHGR5
3
7
C1855
FTG 6-10 MFS-MORB STRAIGHT
4
8
D0549
FTG 16-8 MORB-FORB STRAIGHT REDUCER
1
917767
HOSE SUCT 1.25 10FT
1
10
C0075
HOSE CLAMP HC125
2
11
C4747
FTG 20-16 HB-MAORB 45
1
12 10094
GAUGE OIL LF 2.5" 0-5000 BM
1
13 25630
FTG 10-4 MORB-FP STRAIGHT
1
14
C2376 FTG 8-8 MFS-FFSS 90
1
15 1554
FTG 8-8 MFS-MORB STRAIGHT
1
16 31676
HOSE 0.50(471TC-JC-JC-8-8-8-120)
1
17
C2252
FTG 8-10 MFS-MORB STRAIGHT
1
18 84341
MNT KIT RSRVR 10GAL
1
19 86117
RSRVR ASM 10GAL K MODEL W/ TANK TOP FILTER
1
20
C2142
FTG 12-12 MFS-MORB STRAIGHT
1
21
C5968
FTG 12-12 MFS-MAORB 90
1
22 87077
HOSE 0.75(300PSI)-12FFSS SHORT-12FFSS 90 SHORT-7.50CL
1
23
C5552
FILTER STRAINER TFS-1220-0
1
PN 87081
Reservoir Assembly (Air Controls) - PN 87081

Stellar®120-16-20 Shuttle Owner’s Manual | Page 11
Reservoir Subassembly - PN 86117
ITEM PART DESCRIPTION QTY.
1 C2126 MAGNETIC PLUG DRAIN 3/4" 1
215463
THERMO SIGHT GAUGE ZINGA SG-O5-A-T-N 1
373278
CAP FILL 1PSI ZINGA THREADED 1
413002
DECAL HYD OIL SPECIFICATION MOBIL 1
586118
RSRVR 10GAL K MODEL W/ TANK TOP FILTER 1
686123
FILTER TANK TOP SFM 12 SAE 1
75591
WASHER 0.31 SAE FLAT YELLOW GR8 2
80420
CAP SCR 0.31-18X0.75 HHGR5 2
986129
HOSE 1.25X7.50 DOWN TUBE 1
10
C4659 HOSE CLAMP #16 SS 1
PN 86117
5
2
3
1
4
7
8
6
9
10
NOTE: REPLACEMENT
OIL FILTER - PN 86124
NOTE: REPLACEMENT
GASKET RG-14 - PN 98200
NOTE: FILTER GAUGE - PN 16145
COMES WITH FILTER - PN 86123

Page 12 | Stellar®120-16-20 Shuttle Owner’s Manual
Step 7: Install hydraulic reservoir and valve bank continued...
2 Section Valve Bank w/ Cable Controls
2 Section Valve Bank w/ Air Controls
NOTE: INSTALL PORT RELIEF HERE WHEN PN'S
FROM THE FOLLOWING LIST ARE USED.
TILT ASM'S:
PN 83048 USES PORT RELIEF PN 69172 - PORT RELIEF VDM8 3600 PSI
PN 85778 USES PORT RELIEF PN 26184 - PORT RELIEF VDM8 3300 PSI
NOTE: INSTALL PORT RELIEF HERE WHEN PN'S
FROM THE FOLLOWING LIST ARE USED.
TILT ASM'S:
PN 83048 USES PORT RELIEF PN 69172 - PORT RELIEF VDM8 3600 PSI
PN 85778 USES PORT RELIEF PN 26184 - PORT RELIEF VDM8 3300 PSI

Stellar®120-16-20 Shuttle Owner’s Manual | Page 13
Valve Bank Parts Drawing
SPOOL SPRING KIT
WITH COVER PN 43776
AIR ACTUATOR
PN 26566
HANDLE ASM - OUTSIDE
CTRLS WITH HANDLE PN 30381
SPOOL RETAINER
PN 61522
MAIN RELIEF VALVE
PN 28510
HANDLE
PN 26130
SPOOL SEAL KIT
PN 29683

Page 14 | Stellar®120-16-20 Shuttle Owner’s Manual
Step 8: Install PTO and pump.
• Before installing the pump to the PTO, always check the direction of the PTO output shaft
to determine which direction the hydraulic pump needs to rotate to operate the equip-
ment. If this is not determined prior to installing the hydraulic pump, the hydraulic pump
may rotate in the incorrect direction and damage the front shaft seal.
PTO Direction of Rotation Tip:
Viewed by standing at the rear of the vehicle, looking forward at the PTO shaft, with the
PTO shaft pointing toward the rear of the vehicle:
Remember that the PTO is specified by looking from the rear of the truck to the front of the
truck. The driven equipment (pump) is specified by looking from the front of the truck to
the rear of the truck.
• Use the brand specific PTO/Pump installation instructions. If the directions are not quite
clear, contact Stellar®Customer Service or consult with a hydraulic specialty house or
company prior to installation.
PTO
DRIVEN
EQUIPMENT
(PUMP)
DRIVEN
EQUIPMENT
(PUMP)
TRANSMISSION
TRANSMISSION
From rear of truck,
PTO shaft rotates
opposite engine/
clockwise.
From front of truck,
pump shaft rotates
counterclockwise.
From front of truck,
pump shaft rotates
clockwise.
From rear of truck,
PTO shaft rotates with
engine/counterclockwise.
PTO
P.T.O. Driven E
q
ui
p
ment
Rotates Opposite Engine
(looks "clockwise)
Driven equipment must rotate
counterclockwise (also called left-hand
rotation, "A" for anti-clockwise or C.C.W. for
counter clockwise).
Rotates With Engine
(looks "counterclockwise")
Driven equipment must rotate clockwise
(also called right-hand rotation or "C" for
clockwise).