stellar labs Slider40 User manual

Slider40 Hooklift
Owner’s Manual
Stellar Industries, Inc.
190 State Street
PO Box 169
Garner, IA 50438
800-321-3741
Fax: [phone]
www.stellarindustries.com
Subject to Change without Notication.
© 2016 Stellar Industries, Inc. Last Revision: 03/10/16
Installation • Assembly Drawings • Parts

Page ii | Stellar®Slider40 Owner’s Manual
Slider Hooklift Manual Revisions
Date of Revsion Section Revised Description of Revision

Stellar®Slider40 Owner’s Manual | Page iii
Table of Contents
Introduction .............................................................................................................................................................iv
Hooklift Nomenclature ........................................................................................................................................... v
Chapter 1 - Specications.......................................................................................................................................... 1
Slider40 Specications ............................................................................................................................................ 1
Slider40 Latch Locations for Skid Compatibility .................................................................................................. 2
Slider40 Grease Zerk Locations ............................................................................................................................. 3
Serial Tag Location ................................................................................................................................................. 4
Chapter 2 - Installation ............................................................................................................................................... 5
General Installation ................................................................................................................................................ 5
Installer Notice ..................................................................................................................................................... 5
Torque Data Chart .............................................................................................................................................. 6
Installation Note ................................................................................................................................................... 7
Step 1: Set the hooklift onto the truck frame. ..................................................................................................... 7
Step 2: Drill mounting holes. .................................................................................................................................. 7
Step 3: Install bumper. ............................................................................................................................................ 8
Step 4: Install tie-downs. ......................................................................................................................................... 8
Step 5: Install tarper tower (If applicable). .......................................................................................................... 9
Step 6: Install hydraulic reservoir and valve bank. ............................................................................................. 9
Step 7: Install PTO and pump. ............................................................................................................................. 12
Step 8: Route hydraulic hoses. ............................................................................................................................ 13
Hose Kit - PN 59880 (Fixed Hook Height Models) ........................................................................................... 13
Hose Kit - PN 59881 (Adjustable Hook Height Models) .................................................................................. 14
Power Beyond VDM8 Valve ............................................................................................................................. 15
Step 9: Route Electrical Components ................................................................................................................ 16
Step 10: Install cab and PTO controls. ................................................................................................................ 17
Cable Controls ................................................................................................................................................... 17
Air Controls ......................................................................................................................................................... 18
Optional - Controller Pedestal Reinforcement .............................................................................................. 19
Step 11: Install mud aps and fenders. .............................................................................................................. 20
Step 12: Install Hoist Up Light Sensor - PN 31806 ................................................................................................ 20
Step 13: Apply Decals .......................................................................................................................................... 21
Step 14: Fill reservoir and activate hydraulic ow. ............................................................................................ 22
Step 15: Operate hooklift. .................................................................................................................................... 22
Set System Relief Pressure ................................................................................................................................. 23
Chapter 3 - Assembly Drawings .............................................................................................................................. 25
Base Assembly - PN 56080 ................................................................................................................................... 25
Dump Assembly - PN 56164 ................................................................................................................................. 26
Outside Latch Assembly - PN 56842 (Optional) ................................................................................................ 27
Inside Latch Assembly - PN 54216 (Optional) .................................................................................................... 27
Secondary Assembly - PN 56774 ......................................................................................................................... 28
Main Cylinder Assembly - PN 57019 .................................................................................................................... 29
Jib Assembly (54” Hook Height) - PN 59879 ....................................................................................................... 30
Jib Assembly (61.75” Hook Height) - PN 56775 .................................................................................................. 31
Jib Assembly (54/61.75” Hook Height) - PN 58230 ........................................................................................... 32
Hose Track - PN 58142 .......................................................................................................................................... 34
Slider40 Cylinder Assemblies ................................................................................................................................ 35
Valve Bank Parts Drawing .................................................................................................................................... 36
Toolbox Assembly - PN 8480 ................................................................................................................................ 37
Toolbox Assembly - PN 10401 .............................................................................................................................. 38
Toolbox Assembly - PN 10402 .............................................................................................................................. 39

Page iv | Stellar®Slider40 Owner’s Manual
Introduction
A copy of this manual is provided with every hooklift and can be found in the hard plastic
manual case that is installed on the chassis. A copy of this manual shall remain with the
hooklift at all times.
Throughout the manual, three signal words will be used to bring attention to important
items:
A NOTICE signal word indicates a practice not related to physical injury.
A WARNING signal word indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
A DANGER signal word indicates a hazardous situation which, if not
avoided, will result in death or serious injury.
Information contained within this manual does not cover operation, maintenance, or trou-
bleshooting. Please refer to the General Slider Hooklift Manual for details on these items.
This manual is not binding. Stellar Industries, Inc. reserves the right to change, at any time,
any or all of the items, components, and parts deemed necessary for product improve-
ment or commercial/production purposes. This right is kept with no requirement or obliga-
tion for immediate mandatory updating of this manual.
In closing:
If more information is required or technical assistance is needed, or if you feel that any part
of this manual is unclear or incorrect, please contact the Stellar Customer Service Depart-
ment by phone at 800-321-3741 or email at [email protected].
WARNING
NOTICE
DANGER
For Technical Questions, Information, Parts, or Warranty, Call Toll-Free at
800-321-3741
Hours: Monday - Friday, 8:00 a.m. - 5:00 p.m. CST
Or email at the following addresses:
Technical Questions, and Information [email protected]
Order Parts [email protected]
Warranty Information [email protected]

Stellar®Slider40 Owner’s Manual | Page v
Hooklift Nomenclature
The Stellar® Slider is a hydraulic, body-loading device when mounted on a truck chassis. It
can handle a multitude of bodies ranging from atbeds to recycling containers and dump
bodies.
The Slider consists of four basic parts: the base, dump, secondary, and jib sections. Please
take the time to familiarize yourself with the various components. Knowing the proper ter-
minology is necessary to get the full benet of this manual.
BASE
DUMP
JIB
SECONDARY
HOOKLIFT

Page vi | Stellar®Slider40 Owner’s Manual
This page intentionally left blank.

Stellar®Slider40 Owner’s Manual | Page 1
L
K
A
G
J
EB
C
C
D
H
I
Chapter 1 - Specications
54” (1,372mm) Fixed Hook Height 61.75” (1,569mm) Fixed Hook Height 54” (1,372mm) to 61.75” (1,569mm)
Adjustable Hook Height
Lifting Capacity 37,000 lbs (16,783 kg) 40,000 lbs (18,144 kg) 37,000 lbs - 40,000 lbs (16,783 kg -
18,144 kg)
Dumping Capacity 40,000 lbs (18,144 kg) 40,000 lbs (18,144 kg) 40,000 lbs (18,144 kg)
A Dump Angle 51° 51° 51°
B Lowest Hook Height 47.75” (1,213 mm) 40.75” (1,035 mm) 47.75” or 40.75” (1,213 mm or 1,035
mm)
C Effective Length 132” to 168” (3,353 to 4,267 mm) 132” to 168” (3,353 mm to 4,267 mm) 132” to 168” (3,353 mm to 4,267 mm)
D Truck Frame Height 43” (1,092 mm) 43” (1,092 mm) 43” (1,092 mm)
E Hooklift Height 55” (1,397 mm) 55” (1,397 mm) 55” (1,397 mm)
G Hooklift Length 180” (4,572 mm) 180” (4,572 mm) 180” (4,572 mm)
H Hooklift Center of Gravity 76” (1,930 mm) 76” (1,930 mm) 69.50” (1,765 mm)
I Chassis Cab to Trunion 130” to 144” (3,302 mm to 3,658
mm)***
130” to 144” (3,302 mm to 3,658
mm)*** 130” to 144” (3,302 mm to 3,658 mm)***
JMax. Height When Loading 152” (3,861 mm) 157” (3,988 mm) 157” (3,988 mm)
K Longest Body When Dumping 228” (5,791 mm) 228” (5,791 mm) 228” (5,791 mm)
LMax. Height When Dumping 230” (5,842 mm) 230” (5,842 mm) 230” (5,842 mm)
Maximum Operating Pressure 4,500 psi (31 MPa) 4,500 psi (31 MPa) 4,500 psi (31 MPa)
Hydraulic Flow 20 gpm (76 lpm) 20 gpm (76 lpm) 20 gpm (76 lpm)
Shipping Weight 4,200 lbs (1,905 kg) 4,250 lbs (1,928 kg) 4,550 lbs (2,064 kg)
Shipping Dimensions (LxWxH) 182” x 79” x 48” 182” x 79” x 48” 182” x 86” x 48”
Minimum Truck GVWR 43,000 lbs (19,504 kg) 43,000 lbs (19,504 kg) 43,000 lbs (19,504 kg)
Load Angle w/Shortest Body Length 38° 36° 36° or 34°
Recommended Container Lengths* 12’ to 16’ (3.6 m to 4.9 m) 12’ to 16’ (3.6 m to 4.9 m) 12’ to 16’ (3.6 m to 4.9 m)
Recommended Flatbed Lengths** to 18’ (5.5 m) to 18’ (5.5 m) to 18’ (5.5 m)
*Assumes 3 ft. overhang from center
of rear roller pin (Bumper typically 12”
from center of roller pin)
**Assumes 5 ft. overhang from center
of rear roller pin (May require bumper
and latch options)
***Weight Distribution Required
Slider40 Specications

Page 2 | Stellar®Slider40 Owner’s Manual
39.75120.32
167.82
145.94
NOTE: EFFECTIVE LENGTH
NOTE: OUTSIDE LATCHES
NOTE: INSIDE LATCHES
Slider40 Latch Locations for Skid Compatibility

Stellar®Slider40 Owner’s Manual | Page 3
Slider40
Note: Grease After Every 100 Cycles.
QTY. (2) QTY. (2)
QTY. (2)
QTY. (2)
QTY. (2)
QTY. (2)
QTY. (2)
QTY. (2) BOTH ENDS OF CYLINDER
QTY. (2)
Slider40 Grease Zerk Locations

Page 4 | Stellar®Slider40 Owner’s Manual
The serial tag should be located on the right side (passenger side) of the base assembly:
FOR SERVICE ON THIS EQUIPMENT
CONTACT:
STELLAR INDUSTRIES, INC.
190 STATESTREET, GARNER, IA 50438
641-923-3741
800-321-3741
4214
®
35234
ProudlyDesigned
andManufactured
inthe USA by
MODELNO. SERIALNO.
DATE
MADEIN THE U.S.A. BY STELLAR INDUSTRIES, INC. PN C5942
THEFOLLOWING U.S. OR FOREIGN PATENTSMAY APPLY:
U.S.PATENTS
6,749,389 6,558,104 5,427,495
5,108,247 6,065,942 5,082,417
CANADIANPATENTS
6,749,389
5,108,247
WARNING
25627 - Rev B
Moving parts can crush
and cut.
Keep hands and arms
clear when operating
equipment.
Crush Hazard
DANGER
Electrocution Hazard
Death or serious injury will result from
inadequate clearance if hooklift, load,
or vehicle becomes electrically
charged.
• Maintain safe clearance from high
voltage power sources.
• Never approach vehicle or load if
equipment is near a high voltage
power source.
55832 - RevA
Serial Tag Location
MODEL NO. SERIAL NO.
DATE
MADE IN THE U.S.A. BY STELLAR INDUSTRIES, INC.
PN C5942
®
PATENT INFORMATION
http://www.stellarindustries.com/ip

Stellar®Slider40 Owner’s Manual | Page 5
Chapter 2 - Installation
Installer Notice
According to Federal Law (49 cfr part 571), each nal-stage manufacturer shall complete the vehi-
cle in such a manner that it conforms to the standards in effect on the date of manufacture of the
incomplete vehicle, the date of nal completion, or a date between those two dates. This require-
ment shall, however, be superseded by any conicting provisions of a standard that applies by its
terms to vehicles manufactured in two or more stages.
Therefore, the installer of Stellar® Hooklifts is considered one of the manufacturers of the vehicle.
As such a manufacturer, the installer is responsible for compliance with all applicable federal and
state regulations. They are required to certify that the vehicle is in compliance with the Federal
Motor Vehicle Safety Standards and other regulations issued under the National Trafc and Motor
Vehicle Safety Act.
Please reference the Code of Federal Regulations, title 49 - Transportation, Volume 5 (400-999), for
further information, or visit http://www.gpoaccess.gov/nara/index.html for the full text of Code of
Federal Regulations.
General Installation
This chapter is designed to serve as a general guide for the installation of a Stellar®Slider40
Hooklift. Each installation is considered unique so certain portions of this chapter may or
may not apply to your direct application. If a question should arise during the installation
process, please contact Stellar Customer Service at [phone].
PTO and Pump installation instructions are provided by the corresponding manufacturers.
For more information on which PTO and Pump t your application, please contact your
local Stellar Distributor or Stellar Customer Service.
Do not install this hooklift on a chassis not capable of handling the loads
imposed on it. Failure to do so may result in serious injury or death.
Do not weld or drill holes into the side wall of the base tubes.
Hooklift Mounting and Assembly
Study names and locations of the parts and familiarize yourself with the hooklift before
starting the assembly . Reading the step-by-step instructions that follow will be helpful.
Assembly
Select an area for assembly that will be large enough to accommodate the completed
unit. The surface of the work area should be as level as possible. Use the proper hand
tools to ensure proper bolt tightness. Refer to the torque data chart in this chapter for the
recommended torque values for different sizes of bolts.
Model Number
Know the model number of the Stellar® Hooklift being mounted. Use this model number
whenever referring to the assembly or parts listing pages. The number is stamped on the
name plate which is located on the front frame member.
WARNING
NOTICE

Page 6 | Stellar®Slider40 Owner’s Manual
When using the torque data in the
chart, the following rules should be
observed:
• Bolt manufacturer’s particular
specications should be consulted
when provided.
• Flat washers of equal strength
must be used.
• All torque measurements are giv-
en in foot-pounds. To convert to
inch-pounds, multiply by 12.
• Torque values specied are for
bolts with residual oils or no special
lubricants applied. If special lubri-
cants of high stress ability, such as
Never-Seez compound graphite
and oil, molybdenum disulphite,
colloidal copper or white lead are applied, multiply the torque values in the charts by the
factor .90. The use of Loctite does not affect the torque values listed above.
• Torque values for socket-head capscrews are the same as for Grade 8 capscrews.
• Do not use these values if a different torque value or tightening procedure is given for
a specic application. Torque values listed are for general use only. Check tightness of
fasteners periodically.
• Sheer bolts are designed to fail under predetermined loads. Always replace shear bolts
with identical grade.
• Fasteners should be replaced with the same or higher grade. If higher grade fasteners
are used, these should only be tightened to the strength of the original.
• Tighten plastic insert or crimped steel-type lock nuts to approximately 110 percent of the
dry torque values shown in the chart below, applied to the nut, not to the bolt head.
Tighten toothed or serrated-type lock nuts to the full torque value. Note: “Lubricated”
means coated with a lubricant such as engine oil, or fasteners with phosphate and oil
coatings. “Dry” means plain or zinc plated without lubrication. Tighten lubricated bolts
to approximately 80% of dry bolts.
Size Bolt DIA Plain Plated Plain Plated Plated
(DIA-TPI) (Inches) (Ft-Lb) (Ft-Lb) (Ft-Lb) (Ft-Lb) (Ft-Lb)
5/16-18 0.3125 17 13 25 18 22
3/8-16 0.3750 31 23 44 33 39
7/16-14 0.4375 49 37 70 52 63
1/2-13 0.5000 75 57 105 80 96
9/16-12 0.5625 110 82 155 115 139
5/8-11 0.6250 150 115 220 160 192
3/4-10 0.7500 265 200 375 280 340
7/8-9 0.8750 395 295 605 455 549
1-8 1.000 590 445 910 680 823
1 1/8-7 1.1250 795 595 1290 965 1167
1 1/4-7 1.2500 1120 840 1815 1360 1646
1 3/8-6 1.3750 1470 1100 2380 1780 2158
1 1/2-6 1.500 1950 1460 3160 2370 2865
GRADE 5 GRADE 8 GRADE 9
Torque Data Chart

Stellar®Slider40 Owner’s Manual | Page 7
• When positioning mounts to frame, tie-down castings are bolted to the underside of
each tie down plate located on the outside of the main rails of the base. The tie-down
plate closest to the front of the base requires one mount on each side of the pin. This
is the only time two tie down castings are required per a single tie-down plate. The tie-
down plates are designed with multiple slots to offer more exibility in mounting locations.
Additional holes may not be added to the tie-down plates.
• Using the tie-down castings as a guide, drill 11/16” holes through the truck frame as
shown.
Step 2: Drill mounting holes.
• Visually inspect the truck and look for any potential issues. For example: Clearance
problems, cross members extending too high, insufcient room in front of the Slider for
tarpers, exhaust manifolds, etc., or insufcient room in the rear to allow for bumper se-
lection. Note: Stellar Industries recommends allowing 12” behind the start of clear truck
frame for installation of a tarping system.
• Be sure to square the Slider on the truck frame to allow for proper measurement. The
front of the hooklift needs to be at least 2.50” behind the cab or any equipment mount-
ed behind the cab. Note: On some Slider models, the jib may extend beyond the front
of the base.
Step 1: Set the hooklift onto the truck frame.
Every hooklift installation is unique. However, certain guidelines exist that apply to every
model. Listed below is a general set of chronlological steps that may be followed when
installing a Stellar Hooklift. If any questions arise during the installation process, feel free to
contact your local dealer or Stellar Customer Service at 800-321-3741.
Installation Note
Note: Only the front angle mount requires four (4) bolts to install the angle mount to the truck frame
and four (4) bolts to install the hooklift to the angle mount.
The rear three (3) angle mounts require two (2) bolts each to install the angle mount to the truck frame
and two (2) bolts to install the hooklift to the angle mount.

Page 8 | Stellar®Slider40 Owner’s Manual
Note: See torque chart at beginning of chapter:
Step 4: Install tie-downs.
3
3
4
4
2
8
4
4
3
3
4
4
5
5
4
5
5
4
1
ITEM PART DESCRIPTION QTY.
1 57081PC ANGLE 4.00X6.00X.50WX22.00 SLOTS 2
2
57079PC ANGLE FORMED 4.00X4.00X0.50X12.88 SLOTS 2
35199
CAP SCR 1.00X8X3.00 HHGR8 ZY 40
46538
WASHER 1.00 SAE FLAT YELLOW GR8 80
56294
NUT 1.00 HHGR8 NYLOC 40
8
57733PC ANGLE 4.00X6.00X.50WX11.00 SLOTS 4
PN 57080
• See NHTSA (National Highway
Truck Saftey Administration) Regu-
lations for acceptable placement.
• Modify the truck frame as neces-
sary so that it ends 2” from the rear
of the hooklift.
Step 3: Install bumper.
2.00

Stellar®Slider40 Owner’s Manual | Page 9
• Before drilling and bolting to the frame, conrm adequate room for cable routing be-
tween in-cab controls and the valve bank. Note: The top of the reservoir should not be
above the truck frame.
Step 6: Install hydraulic reservoir and valve bank.
See brand specic installation instructions.
Step 5: Install tarper tower (If applicable).
PN 42426
15
29
19
18
16
23
16
17
2
7
8
25
26
25
22 21
5
24
4
3
63
ITEM PART DESCRIPTION QTY
126510 RSRVR ASM 25GAL K MODEL 1
27353
FTG 32-32 MP-MP HEX NIPPLE STRAIGHT 1
3
C4694 ST EL 1.25 90 DEG BLK 2
4
D0024 NIPPLE 1.25X14.00 BLK 1
5
C6228 FILTER HEAD SF120-25 1.3 1
6
C6225 FILTER LARGE SE-10 1
7
C4750 VALVE BALL 2.00 1
8
C4730 FTG 32-32 MP-HB STRAIGHT 1
924611 VB 2-SECTION VDM81
10 0521
WASHER 0.25 LOCK 3
11 0339
CAP SCR 0.25-20X2.50 HHGR5 3
12
C5968 FTG 12-12 MFS-MAORB 90 1
13
C1855 FTG 6-10 MFS-MORB STRAIGHT 2
14 16152
FTG 10-10 MFS-MORB STRAIGHT 2
15 26737
HOSE 0.75(471TC-JC-J9-12-12-12-24) 1
16 0352
WASHER 0.50 USS FLAT ZINC 12
17
C6106 NUT 0.50-13 HHGR5 NYLOC 6
18 0507
CAP SCR 0.50-13X4.50 HHGR5 6
19 27119
HOSE 0.75(78C-12-JC-JC-12-12-12-120) 1
20 10094
GAUGE OIL LF 2.5" 0-500 BM 1
21
C2375 FTG 20-12 MP-FP REDUCER BUSHING 1
22
C4952 FTG 12-12 MFS-MP STRAIGHT 1
23
13325PC SPACER TANK MOUNTING 25 GAL 2
24 16145
GAUGE PRES FILTER SERVICE CI20 1
25
C4819 HOSE CLAMP 2.00 2
26 17766
HOSE SUCT 2.00 10FT 1
27 25630
FTG 10-4 MORB-FP STRAIGHT 1
28
d1435 FTG 12-10 MFS-MORB STRAIGHT 1
29 c4903 FTG 12-12 MFS-FFSS 90 1

Page 10 | Stellar®Slider40 Owner’s Manual
Step 6: Install hydraulic reservoir and valve bank continued...
PN 42426
ITEM PART DESCRIPTION QTY
924611 VB 2-SECTION VDM81
10 0521
WASHER 0.25 LOCK 3
11 0339
CAP SCR 0.25-20X2.50 HHGR5 3
12
C5968 FTG 12-12 MFS-MAORB 90 1
13
C1855 FTG 6-10 MFS-MORB STRAIGHT 2
14 16152
FTG 10-10 MFS-MORB STRAIGHT 2
20 10094
GAUGE OIL LF 2.5" 0-500 BM 1
27 25630
FTG 10-4 MORB-FP STRAIGHT 1
28
d1435 FTG 12-10 MFS-MORB STRAIGHT 1
11
10
12
28
20
27
14
13
NOTE: PLUG TOP #12 PORT
9

Stellar®Slider40 Owner’s Manual | Page 11
Step 6: Install hydraulic reservoir and valve bank continued...
NOTE: INSTALL PORT RELIEF 26182 HERE WHEN PN'S
FROM THE FOLLOWING LIST ARE USED.
DUMP ASM'S
61350
42429
59439
LATCH KITS
54216
55758
MAIN JIB

Page 12 | Stellar®Slider40 Owner’s Manual
Step 7: Install PTO and pump.
• Before installing the pump to the PTO, always check the direction of the PTO output shaft
to determine which direction the hydraulic pump needs to rotate to operate the equip-
ment. If this is not determined prior to installing the hydraulic pump, the hydraulic pump
may rotate in the incorrect direction and damage the front shaft seal.
PTO Direction of Rotation Tip:
Viewed by standing at the rear of the vehicle, looking forward at the PTO shaft, with the
PTO shaft pointing toward the rear of the vehicle:
Remember that the PTO is specied by looking from the rear of the truck to the front of the
truck. The driven equipment (pump) is specied by looking from the front of the truck to
the rear of the truck.
• Use the brand specic PTO/Pump installation instructions. If the directions are not quite
clear, contact Stellar®Customer Service or consult with a hydraulic specialty house or
company prior to installation.
PTO
DRIVEN
EQUIPMENT
(PUMP)
DRIVEN
EQUIPMENT
(PUMP)
TRANSMISSION
TRANSMISSION
From rear of truck,
PTO shaft rotates
opposite engine/
clockwise.
From front of truck,
pump shaft rotates
counterclockwise.
From front of truck,
pump shaft rotates
clockwise.
From rear of truck,
PTO shaft rotates with
engine/counterclockwise.
PTO
P.T.O. Driven E
q
ui
p
ment
Rotates Opposite Engine
(looks "clockwise)
Driven equipment must rotate
counterclockwise (also called left-hand
rotation, "A" for anti-clockwise or C.C.W. for
counter clockwise).
Rotates With Engine
(looks "counterclockwise")
Driven equipment must rotate clockwise
(also called right-hand rotation or "C" for
clockwise).

Stellar®Slider40 Owner’s Manual | Page 13
1. Route hose line from the reservoir to the pump (See hose kit drawing for details).
2. Route hose line from the pump to the valve bank (See hose kit drawing for details).
3. Route hose line from the valve bank to the reservoir (See hose kit drawing for details).
4. Route hose line from the valve bank and the hooklift (See hose kit drawing for details).
Note: If using the Power Beyond feature for additional function, see “Power Beyond VDM8
Valve” later in this chapter for further details.
Notes on hose line routing:
• Protect these lines with hose wrap when necessary.
• Keep these lines away from sharp edges.
• Keep these lines away from the exhaust or other temperature extreme items.
• Keep these lines away from the driveshaft or other moving items.
Hose Kit - PN 59880 (Fixed Hook Height Models)
PN 59880
Step 8: Route hydraulic hoses.

Page 14 | Stellar®Slider40 Owner’s Manual
Hose Kit - PN 59881 (Adjustable Hook Height Models)
PN 59881