stellar labs SI-60 User manual

Stellar Industries, Inc.
190 State Street
PO Box 169
Garner, IA 50438
800-321-3741
Fax: [phone]
www.stellarindustries.com Last Revision: 06/22/16
Subject to Change without Notification.
© 2016Stellar Industries, Inc.
Safety • Operation • Installation • Parts
Owners’ Manual
sI Cable HOIst
SI-60 and SI-75 Models

Stellar Cable Hoist Manual Revisions
Date of Revision Description of RevisionSection Revised

Stellar®SI Cable Hoist Owner’s Manual | Page i
Table of Contents
Introduction.....................................................................iii
Chapter 1 - Safety .......................................................... 1
Safety Decals of Note ....................................................................3
Chapter 2 - Operation ................................................... 5
General Guidlines for Operation of the Cable Hoist ..................6
Loading Operation .........................................................................7
Unloading Operation - O.R. and I.O. Models ..............................8
Unloading Operation - Extendable Tail Models ..........................9
Correct Roll-Off Container Loads ...............................................10
Unsafe Roll-Off Container Loads.................................................10
Hoist Prop Operation ....................................................................11
Chapter 3 - Maintenance............................................ 13
Inspection of Sheaves ..................................................................14
Cable Replacement .................................................................... 15
Choice Lubricants for DX Bearings..............................................16
Chapter 4 - Specications........................................... 17
Cable Hoist Dimensions................................................................18
Container Subframe.....................................................................19
Chapter 5 - Installation ................................................ 21
General Install Guidelines ............................................................ 21
Truck Chassis Specications.........................................................22
Dimensions: 174 Models ...............................................................23
Dimensions: 182 Models ...............................................................24
Dimensions: 194 Models ...............................................................25
Step 2: Mount Hoist .......................................................................26
Step 3: Mount Lift Cylinders..........................................................27
Mount Lift Cylinders Continued...................................................28
Step 4: Hydraulic Reservoir Installation .......................................28
Step 5: Base Clamp Installation...................................................29
Optional Extender Clamp Install for 182/194 Models ...............30
Step 7: Hydraulic Relief Pressure Setting.....................................31
Step 8: Cable Control Installation ...............................................31
Step 9: Air Control Installation...................................................... 32
Optional Controller Bracket.........................................................33
Step 10: Bumper Installation ........................................................34
Bumper Installation Continued.................................................... 35
Heavy Duty ICC Bumper Installation .......................................... 35
Step 11: Hoist Up Light Installation...............................................36
Step 12a: Fender Installation - Steel Tandem/Tri-Axle............... 37
Step 12b: Fender Installation - Plastic Tandem/Tri-Axle ............38
Step 13: Mid-Body Light Installation ............................................ 38
Step 14a: Removable Stop Installation ......................................39
Step 14b: Intermediate Stop Installation ....................................40
Step 15: Reective Tape Installation ...........................................41
Step 16: Apply Decals .................................................................. 42
Chapter 6 - Hydraulics - Electrical ............................. 43
Hydraulic Schematic ....................................................................43
Hydraulic Routing - Standard Lift Cylinder .................................44
Hydraulic Routing - Telescopic Lift Cylinder............................... 45
Hydraulic Routing - Reverse Mount Lift Cylinder ....................... 46
Reverse Mount Lift Cylinder Mounting Kit - PN 56094 ...............47
Hydraulic Routing - Reeving Cylinder.........................................49
Hydraulic Routing - Tail Extension IOX Cylinder Mount .............50
Hydraulic Routing - Tail Extension ORX Cylinder Mount............51
Electrical Schematics ...................................................................52
Chapter 7 - Assembly Drawings ................................. 53
Main Hoist Assembly .....................................................................53
Cable Guide Roller - PN 46029 ....................................................54
Reeving Cylinder Assembly - PN 60219 ......................................55
Reeving Cylinder Assembly - PN 60221 ......................................55
Chassis Mounted Parts .................................................................56
Chassis Mounted Parts .................................................................57
Mounting Kit (Forward Mount) - PN 55261 .................................58
Mounting Kit (Reverse Mount) - PN 56094..................................59
Mounting Kit (Telescopic) - PN 55265..........................................60
Cab Guard - PN 47263 .................................................................61
Under Body Tool Box - PN 46579 ..................................................62
Reservoir Assembly - PN 46133.....................................................63
2 Section Valve Bank Reservoir - PN 45710.................................64
3 Section Valve Bank Reservoir - PN 46642.................................65
Reservoir Mounting Bracket for PN 45710 ..................................66
Standard Lighted Bumper - PN 45887.........................................67
Pintle Bumper - PN 46818 .............................................................68
ICC Wide Bumper - PN 53397 ......................................................69
ICC Heavy Duty Bumper - PN 46809........................................... 70
ICC Bumper Weldment - PN 45574 .............................................71
ICC Standard Narrow Bumper - PN 48848 .................................72
ICC Narrow Bumper - PN 48846 ..................................................73
ICC Extendable Bumper - PN 62663 ........................................... 74
Tri-Axle Fenders - PN 46299...........................................................75
Tandem Fenders - PN 46122.........................................................76
Tandem Fenders - PN 46122 Continued..................................... 77
Tandem Poly Fenders - PN 45795 ................................................78
Tri-Axle Poly Fenders - PN 45893...................................................79
Standard Lift Cylinder - PN 55262 ................................................ 80
Telescopic Lift Cylinder - PN 51078..............................................80
Standard Reeving Cylinder - PN 51080.......................................81
Long Reeving Cylinder - PN 51201 ..............................................81
Tail Extension Cylinder - PN 51202................................................82
Tail Extension Cylinder - PN 51203................................................82
Ratchet Strap Kit - PN 45896 ........................................................83
SS Hold Down Kit - PN 60793 ........................................................84
CS Hold Down Kit - PN 45326 .......................................................85
Chapter 8 - Replacement Parts .................................. 87

Page ii | Stellar®SI Cable Hoist Owner’s Manual
AN OVERVIEW TO OWNER, OPERATOR AND
SERVICE PERSONNEL ABOUT SAFETY
As the owner or employer, it is your responsibility to instruct the operator in the safe opera-
tion of this equipment and to provide the operator with properly maintained equipment.
FAILURE TO READ THIS MANUAL BY ANYONE WHO WILL OPERATE, SERVICE, OR WORK
AROUND THIS CABLE HOIST IS A MISUSE OF THE EQUIPMENT. DEATH OR SERIOUS INJURY
WILL RESULT FROM IMPROPER USE OR MAINTENANCE OF THIS MACHINE.
Occupational safety is a prime concern of Stellar Industries in the design and production
of this cable hoist. Our goal in writing this manual was the safety of the operator and oth-
ers who work around this equipment.
It is your responsibility to know the specific requirements, governmental regulations, pre-
cautions and work hazards that exist in the operation and maintenance of this cable
hoist. You shall make these available and known to all personnel working with and
around the equipment, so that all of you will take the necessary and required safety pre-
cautions.
FAILURE TO HEED THESE INSTRUCTIONS CAN RESULT IN SERIOUS INJURY OR DEATH.
It is also your responsibility to operate and maintain your cable hoist with caution, skill, and
good judgment. Following the recognized safety procedures will help you avoid acci-
dents. Modification to any part of his cable hoist can create a safety hazard and there-
fore shall not be made without the manufacturer’s written approval. Use only factory
approved accessories, options, and parts on this equipment. The rebuilding or remounting
of this equipment requires the mounting procedures and retesting to be in accordance
with factory instructions. Safety covers and devices must remain installed and maintained
in proper working condition. Safety decals must be maintained, be completely legible,
and be properly located. If safety covers, devices, or decals are missing, they must be
replaced with the proper designated Stellar part.
Be capable, careful, and concerned! Make safety your everyday business!
Attention!
According to Federal Law (49 cfr part 571),
each final-stage manufacturer shall com-
plete the vehicle in such a manner that it
conforms to the standards in effect on the
date of manufacture of the incomplete vehi-
cle, the date of final completion, or a date
between those two dates. This requirement
shall, however, be superseded by any con-
flicting provisions of a standard that applies
by its terms to vehicles manufactured in two
or more stages.
Therefore, the installer of Stellar cable hoists
is considered one of the manufacturers of
the vehicle. As such a manufacturer, the
installer is responsible for compliance with
all applicable federal and state regulations.
They are required to certify that the vehi-
cle is in compliance with the Federal Motor
Vehicle Safety Standards and other regula-
tions issued under the National Traffic and
Motor Vehicle Safety Act.
Please reference the Code of Federal
Regulations, title 49 - Transportation, Volume
5 (400-999), for further information, or visit
www.gpoaccess.gov/nara/index.html for
the full text of Code of Federal Regulations.

Stellar®SI Cable Hoist Owner’s Manual | Page iii
For Technical Questions, Information, Parts, or Warranty, Call Toll-Free at
800-321-3741
Hours: Monday - Friday, 8:00 a.m. - 5:00 p.m. CST
Or email at the following addresses:
Technical Questions, and Information [email protected]
Order Parts [email protected]
Warranty Information [email protected]
Stellar Cable hoists are designed to
provide safe and dependable service for
a variety of operations. With proper use
and maintenance, these cable hoists will
operate at peak performance for many
years.
To promote this longevity, carefully study the
information contained in this manual before
putting the equipment into service. Though
it is not intended to be a training manual for
beginners, this manual should provide solid
guidelines for the safe and proper usage of
the cable hoist.
Once you feel comfortable with the material
contained in this manual, strive to exercise
your knowledge as you safely operate and
maintain the cable hoist. This process is vital
to the proper use of the unit.
A few notes on this manual:
A copy of this manual is provided with
every cable hoist and shall remain with
the cable hoist at all times. Information
contained within this manual does not
cover all maintenance, operating, or repair
instructions pertinent to all possible situations.
Please be aware that some sections of this
manual contain information pertaining to
Stellar manufactured cable hoists in general
and may or may not apply to your specific
model.
This manual is not binding. Stellar Industries,
Inc. reserves the right to change, at any
time, any or all of the items, components,
and parts deemed necessary for product
improvement or commercial/production
purposes. This right is kept with no
requirement or obligation for immediate
mandatory updating of this manual.
In closing:
If more information is required or technical
assistance is needed, or if you feel that any
part of this manual is unclear or incorrect,
please contact the Stellar Customer Service
Department by phone at 800-321-3741 or
email at [email protected].
ATTENTION
Failure to adhere to the
instructions could result in
property damage or even serious
bodily injury to the operator or
others close to the cable hoist.
Introduction

Page iv | Stellar®SI Cable Hoist Owner’s Manual

Stellar®SI Cable Hoist Owner’s Manual | Page 1
Chapter 1 - Safety
Please Read the Following Carefully!
This portion of the manual contains infor-
mation regarding all Stellar manufactured
Cable Hoists. Some items contained within
this chapter may not apply to your specific
equipment.
Safety should be the number one thought
on every operator’s mind. Three factors
should exist for safe operation: a qualified
operator, well-maintained equipment, and
the proper use of this equipment. The fol-
lowing information should be read and
understood completely by everyone work-
ing with or near the Cable Hoist prior to put-
ting the unit into operation.
Please take note that Stellar Industries, Inc.
is not liable for accidents incurred by the
Cable Hoist because of non-fulfillment from
the operator’s side of current rules, laws,
and regulations.
General Safety
It is the responsibility of the owner to instruct
the operator in the safe operation of your
equipment and to provide the operator
with properly maintained equipment.
Trainees or untrained persons shall be under
the direct supervision of qualified persons.
Do not operate equipment under the
adverse influence of alcohol, drugs, or
medication.
Read all safety decals on the equipment
and understand their meaning.
Personal Safety
Keep clear of all moving parts.
Never allow anyone under any portion of
the hoist unless the hoist is firmly resting in
the hoist props.
Always wear the prescribed personal safety
devices.
Always wear approved accident-preven-
tion clothing such as: protective helmets,
anti-slip shoes with steel toes, protective
gloves, anti-noise headphones, protective
glasses, breathing apparatus, and reflective
jackets. Consult your employer regard-
ing current safety regulations and acci-
dent-prevention equipment.
Do not wear rings, wristwatch, jewelry,
loose-fitting or hanging clothing such as ties,
torn garments, scarves, unbuttoned jack-
ets or unzipped overalls, which could get
caught up in the moving parts of the Cable
Hoist.
Keep a first-aid box and a fire extinguisher
readily available on the truck. Regularly
check to make sure the fire extinguisher is
fully charged and the first-aid kit is stocked.
Do not use controls and hoses as hand-
holds. These parts move and cannot pro-
vide stable support.
Do not allow unauthorized personnel or
equipment to enter within 10 feet of Cable
Hoist operating area.
Never allow anyone to ride the Cable Hoist
or load.
Operation Safety
Never operate the hoist unless the hydraulic
system, including the cylinders and lines, are
full of oil and free of air.
Check the area for power lines and over-
head obstructions.
Do not load, dump or unload a container
on uneven ground.
Do not move the truck while the hoist and
container are raised. A raised load creates

Page 2 | Stellar®SI Cable Hoist Owner’s Manual
a top heavy unstable load.
Do not use a chain between the reeving
cable and the container. A chain will not
withstand the force applied to the cable.
Do not use any method to hold a valve
open which will not let the valve close auto-
matically when released.
Always keep the cable centered on the
hoist frame. Do not allow the cable to rub
on any surface when loading or unloading
a container.
Do not operate the reeving cylinders to
load or unload a container unless the front
of the hoist frame is above the top of the
truck cab.
Maintenance Safety
Never modify or alter any of the equipment,
whether mechanical, electrical, or hydrau-
lic, without Stellar Industries’ approval.
Be sure safety decals are clean and in
place.
Check the reeving cable for wear and fray-
ing.
Do not perform any maintenance or repair
work on the Cable Hoist unless authorized
and trained to do so.
Release system pressure before attempting
to make adjustments or repairs.
Do not attempt service or repair when PTO
is engaged.
ATTENTION
Stellar Industries, Inc. is not liable for acci-
dents incurred by the Cable Hoist because
of the operator’s non-fulfillment of current
rules, laws and regulations.

Stellar®SI Cable Hoist Owner’s Manual | Page 3
WARNING
CRUSHING HAZARD
Moving parts can
crush and cut.
Keep hands and
arms clear.
25627
Safety Decals of Note
DANGER
STAND CLEAR
WHEN THIS UNIT IS IN OPERATION!
FAILURE TO DO SO COULD RESULT IN
SERIOUS PERSONAL INJURY.
45557
CAUTION
DO NOT ATTEMPT TO OPERATE
THIS EQUIPMENT WITHOUT PROPER TRAINING.
PERSONAL INJURY AND EQUIPMENT DAMAGE
CAN OCCUR IF THIS EQUIPMENT IS USED IMPROPERLY.
READ AND UNDERSTAND THE OPERATION MANUAL.
45693
DANGER
BE AWARE OF POWER
LINES AND OVERHEAD
OBSTRUCTIONS.
CONTACT BY THE HOIST OR
CONTAINER COULD CAUSE
SERIOUS INJURY OR DEATH
TO THE OPERATOR AND
BYSTANDERS.
45696
WARNING
45698
RAISE HOIST ABOVE THE TOP
OF THE TRUCK CAB BEFORE
LOADING OR UNLOADING A
CONTAINER, UNLESS A CAB
GUARD IS INSTALLED.
CABLE FAILURE COULD RESULT
IN SERIOUS PERSONAL INJURY
AND EQUIPMENT DAMAGE.
WARNING
BEFORE WORKING AROUND A
RAISED HOIST, THE HOIST
MUST BE SUPPORTED BY THE
HOIST PROP.
(SEE HOIST PROP OPERATING
INSTRUCTIONS)
FAILURE TO DO SO COULD RESULT IN
SERIOUS INJURY OR DEATH.
IF THE HOIST PROPS CANNOT BE
USED, CONSULT THE MAINTENANCE
SECTION OF THE OPERATION MANUAL
FOR THE PROPER PRECAUTIONS.
45553
DO NOT ATTEMPT TO LOAD A CONTAINER
UNLESS THE HOIST AND CONTAINER ARE
CORRECTLY ALIGNED.
KEEP THE CONTAINER RAILS SAFELY
ENGAGED WITH THE HOIST RAILS AND
ROLLERS.
FAILURE TO DO SO COULD CAUSE THE
CONTAINER TO SLIDE OFF THE SIDE OF
THE HOIST OR JAM ON THE RAILS.
WARNING
45692
WARNING
DO NOT LOAD, UNLOAD OR
DUMP CONTAINER ON
UNEVEN GROUND.
A LOADED CONTAINER CREATES A TOP
HEAVY LOAD. USE CAUTION WHEN
DRIVING ON UNEVEN GROUND AND
TURNING CORNERS.
SERIOUS PERSONAL INJURY AND
EQUIPMENT DAMAGE COULD RESULT.
45695
CAUTION
45697
DO NOT EXCEED 1600 ENGINE
RPM WHEN OPERATING
POWER TAKE OFF!
Escaping fluid under pressure can penetrate the skin causing serious injury
or death. Relieve pressure before disconnecting hydraulic lines, tighten all
connections before applying pressure, and inspect all lines before
each use. See "Safety" section in operation manual for additional
information.
If an accident occurs, see a doctor immediately. Any fluid
injected into the skin must be surgically removed within a
few hours or gangrene may result. 45726
74-276
WARNING

Page 4 | Stellar®SI Cable Hoist Owner’s Manual

Stellar®SI Cable Hoist Owner’s Manual | Page 5
Job-Site Set-Up
Thoroughly plan the lift before positioning
the vehicle. Consider the following:
1. The vehicle should be positioned in an
area free from overhead obstructions to
eliminate the need for repositioning.
2. Position the vehicle so that it is impossi-
ble for any portion of the equipment to
come within the minimum required safe
distance of any power line. Maintain a
clearance of at least 10 feet between
any part of the Cable Hoist, load line, or
load, and any electrical line or appara-
tus carrying up to 50,000 volts. One foot
additional clearance is required for every
additional 30,000 volts or less. Remember
to allow for winds that cause power lines
to sway. It is recommended that a signal
person be used when the vehicle is set-
up near power lines.
3. The vehicle should also be positioned on
a firm and level surface that will provide
adequate support for the body.
4. The parking brake must be removed to
allow the truck to roll under the body
while loading.
Cable Hoist Controls
1. Be familiar with the sequence and opera-
tion of the Cable Hoist controls.
2. Each individual Cable Hoist function
should have control function decals.
Replace them immediately if they are
missing or illegible.
3. Keep hands, feet and control levers free
from mud, grease and oil.
4. Be familiar with the control levers and
how they operate before attempting to
operate the Cable Hoist.
5. Be prepared before beginning operation
of the Cable Hoist:
• All protective guards must be in place.
• Be aware of the surroundings: low
branches, power lines, unstable ground.
• Be sure all safety devices provided are
in place and in good operating condi-
tion.
• Be prepared for all situations. Keep fire
extinguisher and first aid kit near.
• Be sure all regular maintenance has
been performed.
• Visually inspect all aspects of the Cable
Hoist for physical damage.
• Check for fluid leaks.
Operator Requirements
Operation is limited to the following people:
1. Qualified individual.
2. Trainees under direct supervision of the
qualified individual.
3. Test or maintenance individual.
4. Cable Hoist Inspector.
Operators must:
1. Demonstrate the ability to understand
all decals, the owner’s manual, and any
other information required for safe opera-
tion of the Cable Hoist.
2. Be able to demonstrate the ability to
safely control the Cable Hoist.
3. Know all safety regulations.
4. Be responsible for maintenance require-
ments.
5. Understand and be fully capable of
implementing all emergency procedures.
6. Understand the operating procedures as
outlined by this manual, ANSI B30.5 and
Federal/State Laws.
Operator Conduct
1. Operators will not engage in any oper-
ation that would cause them to divert
attention away from the operation of the
Cable Hoist.
2. Operators are responsible for all opera-
tions under their direct control.
3. Operators will not leave a suspended
load unattended.
4. Operators will be familiar with the equip-
ment and the maintenance required for
proper care.
Chapter 2 - Operation

Page 6 | Stellar®SI Cable Hoist Owner’s Manual
Loading a Container
1. Back the truck up to the container to be
loaded and align the hoist rails with the
container long sills. Caution: Be sure the
area in which the hoist is to be operat-
ed is clear of personnel and obstacles -
overhead and on the ground.
2. Engage the PTO and raise the hoist until
the rear roller is on the ground.
3. Set the parking brakes and retract the
reeving cylinders to connect the cable to
the container. Caution: Do not attempt
to load a container with faulty equip-
ment. Check the condition of the cable,
cable end, and container cable connec-
tion. Never lift a container heavier than
the rated capacity of the hoist.
4. Relase the parking brake and allow the
truck to roll under the container. Extend
the reeving cylinders to pull the contain-
er onto the hoist. The container long sills
must be kept on the hoist rollers.
5. Once the center of gravity of the con-
tainer is in front of the rear hinge, the
hoist can be lowered until the front is just
above the top of the truck cab.
6. Continue pulling the container forward
until it is securely locked into the front
stops. Caution: Rear hold-down devices
are required on the hoist and the con-
tainers.
7. Lower the hoist to the full-down position
and disengage the PTO.
Dumping a Container
1. While the hoist is in the full-down position,
open the container door and secure it.
Caution: Be sure that the truck is on firm,
level ground before dumping. If one side
of the load breaks loose in this high cen-
ter of gravity position, a truck on unstable
footing may roll over on its side.
2. Engage the PTO and raise the hoist until
the load slides out of the container.
Caution: Do not pull forward until the
hoist is lowered to the full-down position.
3. Lower the hoist to the full-down position
and disengage the PTO.
Unloading a Container (O.R. and I.O.)
1. Back the truck up in front of where the
container is to be spotted. Allow room
for the container to roll off of the hoist.
2. Raise the hoist and retract the reeving
cylinders. Allow gravity to pull the con-
tainer to the ground.
3. Once the rear rollers are on the ground,
allow the truck to roll out from under the
container.
4. Once the container is on the ground,
lock the truck brakes and disconnect the
cable and secure it to the hoist.
5. Lower the hoist to the full down position.
Pull away from the container. Disengage
the PTO.
Unloading a Container (Extendable Tail)
1. Back the truck up in front of where the
container is to be spotted. Allow room
for the container to roll-off of the hoist.
2. Raise the hoist and retract the reeving
cylinders. Allow gravity to pull the con-
tainer to the ground. Once the rear roll-
ers are on the ground, allow the truck to
roll out from under the container.
3. Alternate extending the cable and the
tail until the container is on the ground.
4. Lock the truck brakes and disconnect
the cable and secure it to the hoist.
5. Lower the hoist and retract the tail sec-
tion. Disengage the PTO before driving
away.
General Guidlines for Operation of the Cable Hoist
Cable Hoist Check List
1. Check hydraulic oil level with all
cylinders retracted.
2. Grease all lubrication points.
3. All rollers and sheaves are free to
rotate.
4. Tires are properly inflated.
5. The container lock is free to move and
works properly.

Stellar®SI Cable Hoist Owner’s Manual | Page 7
Loading Operation
Back the truck up to the container
to be loaded and align the hoist rails
with the container long sills.
1
Engage the PTO and raise the hoist
until the rear roller is on the ground.
Set the parking brakes and retract
the reeving cylinders to connect the
cable to the container.
Release the parking brake and allow
the truck to roll under the container.
Extend the reeving cylinders to pull
the container onto the hoist. The
container long sills must be kept on
the hoist rollers.
Once the center of gravity of the
container is in front of the rear hinge,
the hoist can be lowered until the
front is just above the top of the
truck cab.
Continue pulling the container
forward until it is securely locked into
the front stops. Caution: Rear
hold-down devices are required
on the hoist and the containers.
Lower the hoist to the full-down
position and disengage the PTO.
2
3
4
5
6
7

Page 8 | Stellar®SI Cable Hoist Owner’s Manual
Unloading Operation - O.R. and I.O. Models
Back the truck up in front of where the
container is to be spotted. Allow room
for the container to roll-off of the hoist.
1
Raise the hoist and retract the
reeving cylinders. Allow gravity to
pull the container to the ground.
Once the rear rollers are on the
ground, allow the truck to roll out
from under the container.
Once the container is on the ground,
lock the truck brakes and disconnect
the cable and secure it to the hoist.
Lower the hoist to the full down position.
Pull away from the container.
Disengage the PTO.
2
3
4
5

Stellar®SI Cable Hoist Owner’s Manual | Page 9
Unloading Operation - Extendable Tail Models
Back the truck up in front of where the
container is to be spotted. Allow room
for the container to roll-off of the hoist.
1
Raise the hoist and retract the
reeving cylinders. Allow gravity to
pull the container to the ground.
Once the rear rollers are on the
ground, allow the truck to roll out
from under the container.
Alternate extending the cable and
the tail until the container is on the
ground.
Lock the truck brakes and disconnect
the cable and secure it to the hoist.
Lower the hoist and retract the tail
section. Disengage the PTO before
driving away.
2
3
4
5

Page 10 | Stellar®SI Cable Hoist Owner’s Manual
Correct Container Position
Correct Position
For Short Container
Note: Removable front stops must
be used and rear hold downs must
match on container and roll-off
hoist.
Unsafe Roll-Off Container Loads
The Container is Too Long
Load Center is Too Far to the Rear
Front Axle May Be Too Light
Front Axle May Be
Overloaded
Frame may crack or bend.
Frame may crack or bend.
Frame may crack or bend.
Frame may crack or bend.
Frame may crack or bend.
Correct Roll-Off Container Loads

Stellar®SI Cable Hoist Owner’s Manual | Page 11
Hoist Prop Operation
WARNING
BEFORE WORKING AROUND A
RAISED HOIST, THE HOIST
MUST BE SUPPORTED BY THE
HOIST PROP.
(SEE HOIST PROP OPERATING
INSTRUCTIONS)
FAILURE TO DO SO COULD RESULT IN
SERIOUS INJURY OR DEATH.
IF THE HOIST PROPS CANNOT BE
USED, CONSULT THE MAINTENANCE
SECTION OF THE OPERATION MANUAL
FOR THE PROPER PRECAUTIONS.
45553

Page 12 | Stellar®SI Cable Hoist Owner’s Manual

Stellar®SI Cable Hoist Owner’s Manual | Page 13
Please read the following before performing any
maintenance on the Cable Hoist.
1. Only authorized service personnel are to perform
maintenance on the Cable Hoist.
2. Disengage the PTO before any service or repair is
performed.
3. Do not disconnect hydraulic hoses while there is
still pressure in those components.
4. Before disconnecting hydraulic components,
shut off the engine, release any air pressure on
the hydraulic reservoir, and move control levers
repeatedly through their operating positions to
relieve all pressures.
5. Keep the Cable Hoist clean and free from grease
build-up, oil and dirt to prevent slippery condi-
tions.
6. Perform all safety and maintenance checks
before each period of use.
7. Replace parts with Stellar Industries, Inc.
approved parts only.
8. Immediately repair or have repaired any compo-
nents found to be inadequate.
Maintenance Procedures
1. Position the Cable Hoist where it will be out of the
way of other operations or vehicles in the area.
2. Place all controls in the off position and secure
operating features from inadvertent motion.
3. Relieve hydraulic oil pressure from all hydraulic
circuits before loosening or removing hydraulic
components.
4. Label or tag parts when disassembling.
Periodic Inspection
Periodic Inspection should occur while the Cable
Hoist is in use. For the duration of the usage, inspect
the Cable Hoist for all of the following:
1. Loose bolts and fasteners.
2. All pins, bushings, shafts, and gears for wear,
cracks, or distortion to include all pivot points,
and bushings.
3. Hydraulic systems for proper operating pressure.
4. Main frame mount bolts.
5. Cylinders for:
A. Damaged rods.
B. Dented barrels.
C. Drift from oil leaking internally.
D. Leaks at rod seals or holding valves.
6. PTO and hydraulic pump(s) for leaks.
7. Hydraulic hose and tubing for evidence of dam-
age such as blistering, crushing, or abrasion.
8. Presence of this owner’s manual.
Daily Inspection
Daily Inspection should occur each day before the
Cable Hoist is put into use. Each day, inspect the
Cable Hoist for all of the following:
1. Hydraulic oil level.
2. Loose parts or damage to structures or weld.
3. Cylinder movement due to leakage.
4. Hoses for evidence of oil leaks.
5. Controls for malfunction or adjustment.
6. Parking brake operation.
7. All securing hardware such as cotter pins, snap
rings, hairpins, and pin keepers for proper instal-
lation.
8. All safety covers for proper installation.
9. Cylinder holding valves for proper operation.
10. Equipment for missing, illegible, or defaced
operating decals and safety signs.
11. Inspect the wire rope for fraying or other wear.
Monthly Inspection
Monthly Inspection should occur at the beginning
of every work month. Each month, inspect the
Cable Hoist for all of the following:
1. Frame bolt tightness - turn barrel nuts and mount-
ing bolts during the first month of operation on
new machines and then quarterly thereafter.
2. Cylinders and valves for leaks.
3. Lubrication.
4. Structural weldments for bends, cracks, or breaks.
5. All pins and keepers for proper installation.
6. All control, safety, and capacity placards for
readability and secure attachment.
7. Inspect all electrical wires and connections for
worn, cut, or deteriorated insulation and bare
wire. Replace or repair wires as required.
8. Lubrication of all points requiring lubrication.
General Service
The following general suggestions should be helpful
in analyzing and servicing your Cable Hoist. Using
the following systematic approach should be help-
ful in finding and fixing problems:
1. Determine the problem.
2. List and record possible causes.
3. Devise checks.
4. Conduct checks in a logical order to determine
the cause.
5. Consider the remaining service life of compo-
nents against the cost of parts and labor neces-
sary to replace them.
6. Make the necessary repair.
7. Recheck to ensure that nothing has been over-
looked.
8. Functionally test the new part in its system.
Chapter 3 - Maintenance

Page 14 | Stellar®SI Cable Hoist Owner’s Manual
Inspection of Sheaves
Under normal conditions, machines should
receive periodic inspections, and their over-
all condition recorded. Such inspections
usually include the sheaves, and any other
parts that may come into contact with the
wire rope and subject it to wear. As an
additional precaution, rope related work-
ing parts, particularly in the area described
below, should be re-inspected prior to the
installation of a new cable.
The very first item to be checked when
examining the sheaves is the condition of
the grooves. To check the size, contour and
amount of wear, a groove gage is used. As
shown in the illustration to the right of this
paragraph, the gage should contact the
groove for about 150º of arc.
Two types of groove gages are in general
use and it is important to note which of these
is being used. The two differ by their respec-
tive percentage over nominal.
For new or re-machine grooves, the groove
gage is nominal plus the full oversize per-
centage. The gage carried by most wire
rope representatives today is used for worn
grooves and is made nominal plus 1/2 the
oversize percentage.
The latter gage is intended to act as a sort
of “no-go” gage. Any sheave with a groove
smaller than this must be replaced or, in all
likelihood, the existing rope will be dam-
aged.
Experience has clearly demonstrated that
the service life of the wire rope will be mate-
rially increased by strict adherence to these
standards.
Cross-sections illustrating three sheeve-groove conditions.
A is correct, B is too tight, and C is too loose.
Cross-sections illustrating three sheeve-groove conditions.
A is correct, B is too tight, and C is too loose.