STI 13000 Series Instruction sheet

Universal Stopper Install
STI-13000 & STI-14000 Series
Specications
Polycarbonate Enclosure
· Flammability - flush and surface mount models (Fig. 2 & 3): UL 94 V-2, enclosed flush and
enclosed back box models (Fig. 4 & 5): UL 94 5VA
· Cover wall thickness 0.125 inches
Gaskets
STI-1318 3” Gasket - Neoprene 1/8” diameter
Mounting gasket (embedded in housing at STI factory prior to shipping) - Two part polyurethane
STI-6004 1/2” or 3/4” conduit weather gasket - Closed Cell Neoprene
Horn 9V (Battery included) 12V 24V
· Low (95 dB @ 1 ft.) 40mA 38mA 22mA
· High (105 dB @ 1 ft.) 105mA 125mA 95mA
· Min. Operating Req. 2V @ 20mA 4V @ 20mA 4V @ 20mA
Dry Contact Relay
· 30 VAC/VDC, 1A
Temperature Range
· Electronics operating range: -40° to 120°F (-40° to 49°C) Below -4°F (-20°C), a remote
power source is recommended
· Polycarbonate rated: -40° to 284°F (-40° to 140°C)
Installation Notes
· When used outdoors, the manual station must also be rated for outdoor use.
· UL Listing does not permit external power source or connection of horn relay contacts to fire alarm
or life safety devices.
· When properly installed, the operation of this cover will not interfere with the function of your life
safety system.
· Horn operation and performance must be tested annually. Battery replacement is recommended
annually dependent on usage and battery expiration date.
· Ensure the service pin is properly inserted in the service pin receptor to silence horn while performing
installation or servicing horn.
· If mounting to an uneven surface, a backplate (STI-1314) is recommended to help ensure proper
sealing to mounting surface.
· The backplate may be drilled if wire access or screw mounting holes are needed.
4.08 in.
(104mm)
5.42 in.
(138mm)
4.96 in.
(126mm)
4.31 in.
(110mm)
3.25 in.
(83mm)
2.54 in.
(84mm)
2.66 in.
(68mm)
2.0 in.
(51mm)
1.5 in.
(38mm)
1.0 in.
(25mm)
FLUSH END VIEW
.67 in.
(17mm)
5.95 in.
(151mm)WITHOUT HORN
5.28 in.
(134mm)WITH HORN
.42 in.
(11mm)
5.42 in.
(138mm)WITH HORN
6.36 in.
(162mm)WITHOUT HORN
FLUSH SIDE VIEW
LIFT HERE
TEXT HERE
6.45 in.
(164mm)
2.73 in.
(69mm)
2.29 in.
(58mm)
4.58 in.
(116mm)
LIFT HERE
6.45 in.
(164mm)
2.73 in.
(69mm)
2.29 in.
(58mm)
4.58 in.
(116mm)
LIFT HERE
TEXT HERE
6.45 in.
(164mm)
2.73 in.
(69mm)
2.29 in.
(58mm)
4.58 in.
(116mm)
LOCKING
TAB
LOCKING
TAB
LOCKING
TAB
TEXT HERE
Fig. 1 - Dimensions
Center pull station to the Universal Stopper with the help of
dimensions shown in Fig. 1.
Open cover, use frame or optional backplate to mark
mounting holes.
NOTE: Be sure the entire cover travel will not interfere
with operation of the pull station or other safety system
equipment when installed.

Fig. 2 - Flush Mounting Option - Models 130** & 140**
Fig. 3 - Surface Mounting Option - Models 132** & 142**
Fig. 4 - Enclosed Flush Mounting Option - Models 133** & 143** NEMA TYPE 3RX
DRILL 3/16 DIA. HOLES 1-1/4 in. DEEP WHEN
USING ANCHORS
DRILL 7/64 DIA. HOLES 1-1/4 in. DEEP WHEN
ANCHORS ARE NOT USED
WALL ANCHOR
(4) PROVIDED
LOCKING TAB
DRILL 1/8 in. HOLE WHILE COVER IS CLOSED.
INSERT THE BREAKAWAY SEAL (SUB-65) COMPLETELY INTO THE LOCKING TAB.
*NOT USED ON FIRE OR EMERGENCY SIGNAL APPLICATIONS.
#6 x 1-1/4 in. SCREW
(4) PROVIDED
STI-1314 OPTIONAL BACKPLATE -
RECOMMENDED WHEN MOUNTING TO UNEVEN SURFACE
SOLID INSERT
CONDUIT INSERT
#6 x 1-1/4 in. SCREW
(4) PROVIDED
1/2 in. & 3/4 in. CONDUIT
WEATHER GASKET
STI-1314 OPTIONAL BACKPLATE -
RECOMMENDED WHEN
MOUNTING TO UNEVEN SURFACE
DRILL 3/16 DIA. HOLES
1-1/4 in. DEEP WHEN
USING ANCHORS
DRILL 7/64 DIA. HOLES
1-1/4 in. DEEP WHEN
ANCHORS ARE NOT USED
LOCKING TAB
DRILL 1/8 in. HOLE WHILE COVER IS CLOSED.
INSERT THE BREAKAWAY SEAL (SUB-65) COMPLETELY INTO THE LOCKING TAB.
*NOT USED ON FIRE OR EMERGENCY SIGNAL APPLICATIONS.
WALL ANCHOR (4) PROVIDED
3 in. GASKET
APPLY A DROP OF SILICONE
TO HOLD IN PLACE
NOTE: MAY BE TRIMMED
FOR A PROPER FIT AND SEAL
3 in. GASKET
IP67 GROMET FOR REMOTE CABLE OPTION
DRILL 5/8 in. (16mm)
(INCLUDED WITH REMOTE OPTION)
DRILL POINT CENTER LOCATED ON
BACK SIDE OF MOUNTING PLATE
DRILL 3/16 DIA. HOLES 1-1/4 in. DEEP
WHEN USING ANCHORS
DRILL 7/64 DIA. HOLES 1-1/4 in. DEEP
WHEN ANCHORS ARE NOT USED
#6 x 1-1/4 in. SCREW
(4) PROVIDED
#6 - 32 x 1/2 in. PHIL. PANHEAD SCREW
(2) PROVIDED SEALED MOUNTING PLATE (SHOWN)
WALL ANCHOR
(4) PROVIDED
LOCATE GROMET AS NEEDED
DRILL 5/8 in (16mm) HOLE
INSERT GROMET AS SHOWN
FEED WIRES THROUGH GROMET
(INCLUDED WITH SEALED MOUNTING PLATE)
3/4 in. NPT PLUG (1) PROVIDED
USE A FLAT HEAD SCREWDRIVER OR COIN TO REMOVE.
APPLY THREAD SEALANT. SCREW NPT BACK INTO BACK BOX
LOCKING TAB DRILL 1/8 in. HOLE WHILE COVER IS
CLOSED. INSERT THE BREAKAWAY SEAL (SUB-65)
COMPLETELY INTO THE LOCKING TAB.
*NOT USED ON FIRE OR EMERGENCY SIGNAL APPLICATION
#6 O-RING USE TO SEAL
BACK BOX MOUNTING HOLES
(4) PROVIDED
I
P
6
7
A
5 CONDUCTOR
WIRE HARNESS
SERVICE PIN (1) PROVIDED
ROTATE BOTTOM END OF
BATTERY UPWARD FOR REMOVAL
HI
LOW
FACTORY DEFAULT
HIGH
VOLUME SWITCH
#4 HI-LO SCREW
(2) PROVIDED
WHEN REPLACING COVER
MAKE SURE COVER IS UNDER
HORN CASE TAB AND ROTATE
COVER CLOSED. INSERT HI-LO
SCREWS AND TIGHTEN.
HORN COVER
REMOVE BOTH HORN
SCREWS AND ROTATE
COVER OPEN AS SHOWN.
HORN CASE
#6 - 32 x 1/2 in. PHIL. FLATHEAD SCREW
(6) PROVIDED
SERVICE PIN RECEPTOR
ENCLOSED FLUSH MOUNT
COVER ASSEMBLY
#6 1-1/4 in. SCREW
(4) PROVIDED
WALL ANCHOR
(4) PROVIDED
STI-1401 GASKET
EXISTING UL TYPE 3R RATED
IN-WALL ELECTRICAL BOX
DRILL 3/16 DIA. HOLES
1 1/4 in. DEEP WHEN
USING ANCHORS
DRILL 7/64 DIA. HOLES
1 1/4 in. DEEP WHEN
ANCHORS ARE NOT USED
Fit appropriate conduit
weather gasket to
conduit. Then fit gasket
to insert or directly to
the housing knock-out.
For additional seal
reliability a bead
of silicone may be
applied to conduit
fitting.

Fig. 5 - Enclosed Back Box Mounting Option - Models 134**, 135**, 138**, 139**,
144**, 145**, 148** & 149** NEMA TYPE 3RX
DRILL 3/16 DIA. HOLES 1-1/4 in. DEEP WHEN
USING ANCHORS
DRILL 7/64 DIA. HOLES 1-1/4 in. DEEP WHEN
ANCHORS ARE NOT USED
WALL ANCHOR
(4) PROVIDED
LOCKING TAB
DRILL 1/8 in. HOLE WHILE COVER IS CLOSED.
INSERT THE BREAKAWAY SEAL (SUB-65) COMPLETELY INTO THE LOCKING TAB.
*NOT USED ON FIRE OR EMERGENCY SIGNAL APPLICATIONS.
#6 x 1-1/4 in. SCREW
(4) PROVIDED
STI-1314 OPTIONAL BACKPLATE -
RECOMMENDED WHEN MOUNTING TO UNEVEN SURFACE
SOLID INSERT
CONDUIT INSERT
#6 x 1-1/4 in. SCREW
(4) PROVIDED
1/2 in. & 3/4 in. CONDUIT
WEATHER GASKET
STI-1314 OPTIONAL BACKPLATE -
RECOMMENDED WHEN
MOUNTING TO UNEVEN SURFACE
DRILL 3/16 DIA. HOLES
1-1/4 in. DEEP WHEN
USING ANCHORS
DRILL 7/64 DIA. HOLES
1-1/4 in. DEEP WHEN
ANCHORS ARE NOT USED
LOCKING TAB
DRILL 1/8 in. HOLE WHILE COVER IS CLOSED.
INSERT THE BREAKAWAY SEAL (SUB-65) COMPLETELY INTO THE LOCKING TAB.
*NOT USED ON FIRE OR EMERGENCY SIGNAL APPLICATIONS.
WALL ANCHOR (4) PROVIDED
3 in. GASKET
APPLY A DROP OF SILICONE
TO HOLD IN PLACE
NOTE: MAY BE TRIMMED
FOR A PROPER FIT AND SEAL
3 in. GASKET
IP67 GROMET FOR REMOTE CABLE OPTION
DRILL 5/8 in. (16mm)
(INCLUDED WITH REMOTE OPTION)
DRILL POINT CENTER LOCATED ON
BACK SIDE OF MOUNTING PLATE
DRILL 3/16 DIA. HOLES 1-1/4 in. DEEP
WHEN USING ANCHORS
DRILL 7/64 DIA. HOLES 1-1/4 in. DEEP
WHEN ANCHORS ARE NOT USED
#6 x 1-1/4 in. SCREW
(4) PROVIDED
#6 - 32 x 1/2 in. PHIL. PANHEAD SCREW
(2) PROVIDED SEALED MOUNTING PLATE (SHOWN)
WALL ANCHOR
(4) PROVIDED
LOCATE GROMET AS NEEDED
DRILL 5/8 in (16mm) HOLE
INSERT GROMET AS SHOWN
FEED WIRES THROUGH GROMET
(INCLUDED WITH SEALED MOUNTING PLATE)
3/4 in. NPT PLUG (1) PROVIDED
USE A FLAT HEAD SCREWDRIVER OR COIN TO REMOVE.
APPLY THREAD SEALANT. SCREW NPT BACK INTO BACK BOX
LOCKING TAB DRILL 1/8 in. HOLE WHILE COVER IS
CLOSED. INSERT THE BREAKAWAY SEAL (SUB-65)
COMPLETELY INTO THE LOCKING TAB.
*NOT USED ON FIRE OR EMERGENCY SIGNAL APPLICATION
#6 O-RING USE TO SEAL
BACK BOX MOUNTING HOLES
(4) PROVIDED
I
P
6
7
A
5 CONDUCTOR
WIRE HARNESS
SERVICE PIN (1) PROVIDED
ROTATE BOTTOM END OF
BATTERY UPWARD FOR REMOVAL
HI
LOW
FACTORY DEFAULT
HIGH
VOLUME SWITCH
#4 HI-LO SCREW
(2) PROVIDED
WHEN REPLACING COVER
MAKE SURE COVER IS UNDER
HORN CASE TAB AND ROTATE
COVER CLOSED. INSERT HI-LO
SCREWS AND TIGHTEN.
HORN COVER
REMOVE BOTH HORN
SCREWS AND ROTATE
COVER OPEN AS SHOWN.
HORN CASE
#6 - 32 x 1/2 in. PHIL. FLATHEAD SCREW
(6) PROVIDED
SERVICE PIN RECEPTOR
ENCLOSED FLUSH MOUNT
COVER ASSEMBLY
#6 1-1/4 in. SCREW
(4) PROVIDED
WALL ANCHOR
(4) PROVIDED
STI-1401 GASKET
EXISTING UL TYPE 3R RATED
IN-WALL ELECTRICAL BOX
DRILL 3/16 DIA. HOLES
1 1/4 in. DEEP WHEN
USING ANCHORS
DRILL 7/64 DIA. HOLES
1 1/4 in. DEEP WHEN
ANCHORS ARE NOT USED
DRILL 3/16 DIA. HOLES 1-1/4 in. DEEP WHEN
USING ANCHORS
DRILL 7/64 DIA. HOLES 1-1/4 in. DEEP WHEN
ANCHORS ARE NOT USED
WALL ANCHOR
(4) PROVIDED
LOCKING TAB
DRILL 1/8 in. HOLE WHILE COVER IS CLOSED.
INSERT THE BREAKAWAY SEAL (SUB-65) COMPLETELY INTO THE LOCKING TAB.
*NOT USED ON FIRE OR EMERGENCY SIGNAL APPLICATIONS.
#6 x 1-1/4 in. SCREW
(4) PROVIDED
STI-1314 OPTIONAL BACKPLATE -
RECOMMENDED WHEN MOUNTING TO UNEVEN SURFACE
SOLID INSERT
CONDUIT INSERT
#6 x 1-1/4 in. SCREW
(4) PROVIDED
1/2 in. & 3/4 in. CONDUIT
WEATHER GASKET
STI-1314 OPTIONAL BACKPLATE -
RECOMMENDED WHEN
MOUNTING TO UNEVEN SURFACE
DRILL 3/16 DIA. HOLES
1-1/4 in. DEEP WHEN
USING ANCHORS
DRILL 7/64 DIA. HOLES
1-1/4 in. DEEP WHEN
ANCHORS ARE NOT USED
LOCKING TAB
DRILL 1/8 in. HOLE WHILE COVER IS CLOSED.
INSERT THE BREAKAWAY SEAL (SUB-65) COMPLETELY INTO THE LOCKING TAB.
*NOT USED ON FIRE OR EMERGENCY SIGNAL APPLICATIONS.
WALL ANCHOR (4) PROVIDED
3 in. GASKET
APPLY A DROP OF SILICONE
TO HOLD IN PLACE
NOTE: MAY BE TRIMMED
FOR A PROPER FIT AND SEAL
3 in. GASKET
IP67 GROMET FOR REMOTE CABLE OPTION
DRILL 5/8 in. (16mm)
(INCLUDED WITH REMOTE OPTION)
DRILL POINT CENTER LOCATED ON
BACK SIDE OF MOUNTING PLATE
DRILL 3/16 DIA. HOLES 1-1/4 in. DEEP
WHEN USING ANCHORS
DRILL 7/64 DIA. HOLES 1-1/4 in. DEEP
WHEN ANCHORS ARE NOT USED
#6 x 1-1/4 in. SCREW
(4) PROVIDED
#6 - 32 x 1/2 in. PHIL. PANHEAD SCREW
(2) PROVIDED SEALED MOUNTING PLATE (SHOWN)
WALL ANCHOR
(4) PROVIDED
LOCATE GROMET AS NEEDED
DRILL 5/8 in (16mm) HOLE
INSERT GROMET AS SHOWN
FEED WIRES THROUGH GROMET
(INCLUDED WITH SEALED MOUNTING PLATE)
3/4 in. NPT PLUG (1) PROVIDED
USE A FLAT HEAD SCREWDRIVER OR COIN TO REMOVE.
APPLY THREAD SEALANT. SCREW NPT BACK INTO BACK BOX
LOCKING TAB DRILL 1/8 in. HOLE WHILE COVER IS
CLOSED. INSERT THE BREAKAWAY SEAL (SUB-65)
COMPLETELY INTO THE LOCKING TAB.
*NOT USED ON FIRE OR EMERGENCY SIGNAL APPLICATION
#6 O-RING USE TO SEAL
BACK BOX MOUNTING HOLES
(4) PROVIDED
I
P
6
7
A
5 CONDUCTOR
WIRE HARNESS
SERVICE PIN (1) PROVIDED
ROTATE BOTTOM END OF
BATTERY UPWARD FOR REMOVAL
HI
LOW
FACTORY DEFAULT
HIGH
VOLUME SWITCH
#4 HI-LO SCREW
(2) PROVIDED
WHEN REPLACING COVER
MAKE SURE COVER IS UNDER
HORN CASE TAB AND ROTATE
COVER CLOSED. INSERT HI-LO
SCREWS AND TIGHTEN.
HORN COVER
REMOVE BOTH HORN
SCREWS AND ROTATE
COVER OPEN AS SHOWN.
HORN CASE
#6 - 32 x 1/2 in. PHIL. FLATHEAD SCREW
(6) PROVIDED
SERVICE PIN RECEPTOR
ENCLOSED FLUSH MOUNT
COVER ASSEMBLY
#6 1-1/4 in. SCREW
(4) PROVIDED
WALL ANCHOR
(4) PROVIDED
STI-1401 GASKET
EXISTING UL TYPE 3R RATED
IN-WALL ELECTRICAL BOX
DRILL 3/16 DIA. HOLES
1 1/4 in. DEEP WHEN
USING ANCHORS
DRILL 7/64 DIA. HOLES
1 1/4 in. DEEP WHEN
ANCHORS ARE NOT USED
Fig. 6 - Horn Option - Wiring Details - Remote Power/Relay Options
*9V battery acts as a backup power when using remote power
Remove service pin and horn should
sound. Close covers and horn should
silence. When performoing annual battery
test/replacement or when servicing alarm
system, insert service pin to prevent horn
from soundling. Remember to remove to
return to normal operation.
DRILL 3/16 DIA. HOLES 1-1/4 in. DEEP WHEN
USING ANCHORS
DRILL 7/64 DIA. HOLES 1-1/4 in. DEEP WHEN
ANCHORS ARE NOT USED
WALL ANCHOR
(4) PROVIDED
LOCKING TAB
DRILL 1/8 in. HOLE WHILE COVER IS CLOSED.
INSERT THE BREAKAWAY SEAL (SUB-65) COMPLETELY INTO THE LOCKING TAB.
*NOT USED ON FIRE OR EMERGENCY SIGNAL APPLICATIONS.
#6 x 1-1/4 in. SCREW
(4) PROVIDED
STI-1314 OPTIONAL BACKPLATE -
RECOMMENDED WHEN MOUNTING TO UNEVEN SURFACE
SOLID INSERT
CONDUIT INSERT
#6 x 1-1/4 in. SCREW
(4) PROVIDED
1/2 in. & 3/4 in. CONDUIT
WEATHER GASKET
STI-1314 OPTIONAL BACKPLATE -
RECOMMENDED WHEN
MOUNTING TO UNEVEN SURFACE
DRILL 3/16 DIA. HOLES
1-1/4 in. DEEP WHEN
USING ANCHORS
DRILL 7/64 DIA. HOLES
1-1/4 in. DEEP WHEN
ANCHORS ARE NOT USED
LOCKING TAB
DRILL 1/8 in. HOLE WHILE COVER IS CLOSED.
INSERT THE BREAKAWAY SEAL (SUB-65) COMPLETELY INTO THE LOCKING TAB.
*NOT USED ON FIRE OR EMERGENCY SIGNAL APPLICATIONS.
WALL ANCHOR (4) PROVIDED
3 in. GASKET
APPLY A DROP OF SILICONE
TO HOLD IN PLACE
NOTE: MAY BE TRIMMED
FOR A PROPER FIT AND SEAL
3 in. GASKET
IP67 GROMET FOR REMOTE CABLE OPTION
DRILL 5/8 in. (16mm)
(INCLUDED WITH REMOTE OPTION)
DRILL POINT CENTER LOCATED ON
BACK SIDE OF MOUNTING PLATE
DRILL 3/16 DIA. HOLES 1-1/4 in. DEEP
WHEN USING ANCHORS
DRILL 7/64 DIA. HOLES 1-1/4 in. DEEP
WHEN ANCHORS ARE NOT USED
#6 x 1-1/4 in. SCREW
(4) PROVIDED
#6 - 32 x 1/2 in. PHIL. PANHEAD SCREW
(2) PROVIDED SEALED MOUNTING PLATE (SHOWN)
WALL ANCHOR
(4) PROVIDED
LOCATE GROMET AS NEEDED
DRILL 5/8 in (16mm) HOLE
INSERT GROMET AS SHOWN
FEED WIRES THROUGH GROMET
(INCLUDED WITH SEALED MOUNTING PLATE)
3/4 in. NPT PLUG (1) PROVIDED
USE A FLAT HEAD SCREWDRIVER OR COIN TO REMOVE.
APPLY THREAD SEALANT. SCREW NPT BACK INTO BACK BOX
LOCKING TAB DRILL 1/8 in. HOLE WHILE COVER IS
CLOSED. INSERT THE BREAKAWAY SEAL (SUB-65)
COMPLETELY INTO THE LOCKING TAB.
*NOT USED ON FIRE OR EMERGENCY SIGNAL APPLICATION
#6 O-RING USE TO SEAL
BACK BOX MOUNTING HOLES
(4) PROVIDED
I
P
6
7
A
5 CONDUCTOR
WIRE HARNESS
SERVICE PIN (1) PROVIDED
ROTATE BOTTOM END OF
BATTERY UPWARD FOR REMOVAL
HI
LOW
FACTORY DEFAULT
HIGH
VOLUME SWITCH
#4 HI-LO SCREW
(2) PROVIDED
WHEN REPLACING COVER
MAKE SURE COVER IS UNDER
HORN CASE TAB AND ROTATE
COVER CLOSED. INSERT HI-LO
SCREWS AND TIGHTEN.
HORN COVER
REMOVE BOTH HORN
SCREWS AND ROTATE
COVER OPEN AS SHOWN.
HORN CASE
#6 - 32 x 1/2 in. PHIL. FLATHEAD SCREW
(6) PROVIDED
SERVICE PIN RECEPTOR
ENCLOSED FLUSH MOUNT
COVER ASSEMBLY
#6 1-1/4 in. SCREW
(4) PROVIDED
WALL ANCHOR
(4) PROVIDED
STI-1401 GASKET
EXISTING UL TYPE 3R RATED
IN-WALL ELECTRICAL BOX
DRILL 3/16 DIA. HOLES
1 1/4 in. DEEP WHEN
USING ANCHORS
DRILL 7/64 DIA. HOLES
1 1/4 in. DEEP WHEN
ANCHORS ARE NOT USED
Wire Description
Red +12V - 24V
Black -12V - 24V
Blue Common
Green NC - Norm Closed
Yellow NO - Norm Open

2306 Airport Rd • Waterford, MI 48327
Phone: [phone] • Fax: [phone]
[email protected] • www.sti-usa.com
Safety Technology International (Europe) Ltd.
Unit 49G Pipers Road • Park Farm Industrial Estate • Redditch
Worcestershire • B98 0HU • England
Tel: [phone] • Fax: [phone]
E-mail: [email protected] • Web: www.sti-europe.com
Subject to change
without notice.
Printed in USA
Approvals
It has been tested and approved or listed by:
· UL, CUL Listed - S2466
· UL Certified to meet ADA
· NEMA Type 3RX models with enclosed flush mount and enclosed back box options
Warranty
Three year guarantee against breakage of polycarbonate in normal use (one year on electro
mechanical and electronic components).
Electronic warranty form at www.sti-usa.com/wc14.
Important Notice (when used on fire systems)
The Universal Stopper is intended to be used in areas where the incidence of false fire alarms from
manual pull stations is high or has proven to be a serious problem. Any disadvantage of this device
is more than balanced when one considers the consequences of false fire alarms, especially if fire
service personnel and equipment are responding to a false fire alarm when they are needed for a real
fire somewhere else. Add to this, the disruption to the facility when false alarms occur. If you have,
or may have, a problem with false fire alarms or physical/weather damage to your fire alarm activa-
tion devices, the Universal Stopper could prove invaluable. Avis important (en cas d’utilisation sur les
réseaux d’incendie)
Avis important (en cas d’utilisation sur les réseaux d’incendie)
Le Universal Stopper est destiné à être utilisé dans les zones où l’occurrence de fausses alertes d’incendie issues d’avertisseurs
d’incendie manuels est élevée ou présente un problème grave. Un quelconque inconvénient de ce dispositif est vite contrecarré par
les conséquences des fausses alertes d’incendie, surtout lorsque le personnel et l’équipement des services d’incendie réagissent à
une fausse alerte d’incendie alors que leur intervention ailleurs sur un vrai incendie s’avère nécessaire en même temps.À cela s’ajoute
l’agitation éprouvée dans l’établissement au moment du déclenchement d’une fausse alerte. Si vous rencontrez, ou risquez de ren-
contrer, un problème avec les fausses alertes d’incendie ou avec l’éventuel endommagement par effet climatique ou physique de vos
dispositifs de déclenchement des alertes d’incendie, le Universal Stopper pourra alors se révéler d’une valeur inestimable.
Polycarbonate Cleaning Instructions
Rinse with water to remove abrasive dust and dirt. Wash with soap or mild detergent, using a soft
cloth. Rinse once more then dry with a soft cloth or chamois. Exercise caution when using water
inside enclosure. Make sure unit is completely dry inside before reassembling. To remove grease
or wet paint from exterior of cover, rub gently with a soft cloth thoroughly wetted with Naptha. Then
wash and rinse. Do not use razor blades.
Options Available
STI-1314 Universal Stopper Backplate
STI-6602* Horn Assembly
SUB-319 Wiring harness for remote power
SUB-320 Wiring harness for remote power (for STI-1X4XX and STI-1X5XX)
SUB-65 Breakaway Seal (qty. 5)
EA135 Service Pin
*Available in red, green, blue, yellow, white or black.
Univ Stopper IS
Mar 2015